Tensing Dharmaraj
Research Subjects
Tensing Dharmaraj has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Cruze
Department of Civil Engineering, Hindustan Institute of Technology and Science, Chennai, India
2 shared publications - Hemalatha Gladston
Karunya Institute of Technology and Sciences
2 shared publications R. C. Karpagalakshmi
2 shared publications- Vincent Sam Jebadurai S2 shared publications
A. M. Kalpana
1 shared publicationDaniel Cruze
Karunya Institute of Technology and Sciences 1 , Coimbatore 641114, Tamil Nadu
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Precast concrete wall-raft connectors for increasing the lateral load capacity: An experimental and analytical approach
Precast structural walls and rafts commonly resist lateral load in structures owing to improved traits and faster construction. The behavior of five different types of precast reinforced concrete structural wall and raft connection systems is evaluated in this study. In all five configurations, the cyclic load is applied in the wall systems to observe the lateral load-carrying capacity and hysteretic characteristics. The damage and failure patterns were assessed. To confirm and contrast the behavior of the proposed precast structural wall and raft connection systems with the experimental findings, FEM analysis was used. Only shear and flexural cracks were observed. The specimen with 12 mm dia rods has the maximum load carrying capacity of 10.23 kN in the negative cycle, which is 57% more than the specimen without grouting and connector. The suggested connection can improve the resistance behavior in all key directions by absorbing more energy than precast walls under dynamic load.
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessPrecast concrete wall-raft connectors for increasing the lateral load capacity: An experimental and analytical approach
Precast structural walls and rafts commonly resist lateral load in structures owing to improved traits and faster construction. The behavior of five different types of precast reinforced concrete structural wall and raft connection systems is evaluated in this study. In all five configurations, the cyclic load is applied in the wall systems to observe the lateral load-carrying capacity and hysteretic characteristics. The damage and failure patterns were assessed. To confirm and contrast the behavior of the proposed precast structural wall and raft connection systems with the experimental findings, FEM analysis was used. Only shear and flexural cracks were observed. The specimen with 12 mm dia rods has the maximum load carrying capacity of 10.23 kN in the negative cycle, which is 57% more than the specimen without grouting and connector. The suggested connection can improve the resistance behavior in all key directions by absorbing more energy than precast walls under dynamic load.
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Effect of sea sand in the behaviour of fresh concrete partially replaced with M-sand
Effect of sea sand in the behaviour of fresh concrete partially replaced with M-sand
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessEffect of sea sand in the behaviour of fresh concrete partially replaced with M-sand
Effect of sea sand in the behaviour of fresh concrete partially replaced with M-sand
- 1 January 2022
- Published by MIM Research Group in Research on Engineering Structures and Materials
Additive manufacturing techniques in construction
- 1 January 2022
- Published by MIM Research Group in Research on Engineering Structures and Materials
Additive manufacturing techniques in construction
- Open Access
- 5 June 2020
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 14 (1) , 78-93
Development of a Multiple Coil Magneto-Rheological Smart Damper to Improve the Seismic Resilience of Building Structures
Development of a Multiple Coil Magneto-Rheological Smart Damper to Improve the Seismic Resilience of Building Structures
- 5 June 2020
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 14 (1) , 78-93
Open AccessDevelopment of a Multiple Coil Magneto-Rheological Smart Damper to Improve the Seismic Resilience of Building Structures
Development of a Multiple Coil Magneto-Rheological Smart Damper to Improve the Seismic Resilience of Building Structures
- 1 March 2018
- Published by ASTM International in Advances in Civil Engineering Materials
- Vol. 7 (3) , 413-427
Experimental Investigation on Magnetorheological Damper for RCC Frames Subjected to Cyclic Loading
Magnetorheological (MR) fluids with excellent rheological characteristics are capable of exhibiting very quick responses to control vibrations in machines and structures under seismic excitations. The damping properties of MR fluids can be controlled by varying the externally applied magnetic field and current to the fluid. In the present work, MR fluids with nanoscale suspensions were used to eliminate the need of additives and to minimize the settling. The resultant suspensions exhibit good magnetic behavior under damper with off-state and on-state rheology using cyclic load test. The result also showed that the maximum damping force of 2 kN (off-state) and 3.52 kN (on-state) was observed for the MR fluid containing 20 % iron particles in silicone oil. Additionally, the behavior of the MR damper on a reinforced cement concrete (RCC) frame subjected to cyclic loading was studied. To determine the efficiency of the MR damper, an RCC frame was casted and tested with and without damper. The results show that the incorporation of the MR damper reduced the displacement by 49 % and an increase in load carrying capacity of 55 % was attained compared with the RCC frame without damper.
- 1 March 2018
- Published by ASTM International in Advances in Civil Engineering Materials
- Vol. 7 (3) , 413-427
Experimental Investigation on Magnetorheological Damper for RCC Frames Subjected to Cyclic Loading
Magnetorheological (MR) fluids with excellent rheological characteristics are capable of exhibiting very quick responses to control vibrations in machines and structures under seismic excitations. The damping properties of MR fluids can be controlled by varying the externally applied magnetic field and current to the fluid. In the present work, MR fluids with nanoscale suspensions were used to eliminate the need of additives and to minimize the settling. The resultant suspensions exhibit good magnetic behavior under damper with off-state and on-state rheology using cyclic load test. The result also showed that the maximum damping force of 2 kN (off-state) and 3.52 kN (on-state) was observed for the MR fluid containing 20 % iron particles in silicone oil. Additionally, the behavior of the MR damper on a reinforced cement concrete (RCC) frame subjected to cyclic loading was studied. To determine the efficiency of the MR damper, an RCC frame was casted and tested with and without damper. The results show that the incorporation of the MR damper reduced the displacement by 49 % and an increase in load carrying capacity of 55 % was attained compared with the RCC frame without damper.
- 1 December 2016
- Published by American Scientific Publishers in Journal of Medical Imaging and Health Informatics
- Vol. 6 (8) , 1972-1976
Image Localization Using Deformable Model and Its Application in Health Informatics
- 1 December 2016
- Published by American Scientific Publishers in Journal of Medical Imaging and Health Informatics
- Vol. 6 (8) , 1972-1976
Image Localization Using Deformable Model and Its Application in Health Informatics
- 1 October 2016
- Published by American Scientific Publishers in Journal of Computational and Theoretical Nanoscience
- Vol. 13 (10) , 6892-6895
A Comparative Study of Ultimate Strength and Behaviour of Steel Concrete Composite Beam with Shear Connectors Subjected to Pure Torsion
This study concerns the employment of pure torsion analysis to determine ultimate strength of composite beam with shear connectors. The effect of shear connector is used for increasing the strength and stiffness of composite beam. This behavior is influenced by physical response of the beam under pure torsion. Totally 12 beams are tested and comparative analysis has been made within this 12 beams. The curvature, rotation and angle of twist are calculated throughout entire load by torsion test. This investigation proves that the composite beam with 75 mm spaced shear connector provides good ultimate strength.
- 1 October 2016
- Published by American Scientific Publishers in Journal of Computational and Theoretical Nanoscience
- Vol. 13 (10) , 6892-6895
A Comparative Study of Ultimate Strength and Behaviour of Steel Concrete Composite Beam with Shear Connectors Subjected to Pure Torsion
This study concerns the employment of pure torsion analysis to determine ultimate strength of composite beam with shear connectors. The effect of shear connector is used for increasing the strength and stiffness of composite beam. This behavior is influenced by physical response of the beam under pure torsion. Totally 12 beams are tested and comparative analysis has been made within this 12 beams. The curvature, rotation and angle of twist are calculated throughout entire load by torsion test. This investigation proves that the composite beam with 75 mm spaced shear connector provides good ultimate strength.
- 1 December 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 293-298
Vehicle object observation using position based local gradient model
The conception of traffic activities in urban framework is the major endeavor in the study of traffic troubles. This examination is chiefly processed on the maximization of traffic flow, and the minimization of traffic accidents, congestions and pollution. In common, network representations of transport systems are understood to be fixed, but these representations do not permit an exact recreation of seriously packed urban road networks. For this rationale, traffic engineers happened to judge some substitute models such as simple object recognition and localization of road vehicles based on the position and orientation of vehicle image data. But the drawback of the approach is that if the shape of the vehicle and its pose varies in multiple junction coordination, the model based recognition is an inefficient one. To enhance the process of traffic flow mechanism, in this paper, we are going to implement a surveillance image object recognition and localization using improved local gradient model. At first, the vehicle images are taken by camera which is taken on the junction board of the traffic coordination. Based on location, position, angle and height of the camera to be fixed on the junction board, the vehicle images are obtained clearly in an aerial view and extracted the entire road for identifying the vehicle densities and postures using ray traced templates. An experimental evaluation is carried out to estimate the performance of the proposed vehicle object observation using position based local gradient model in terms of vehicle density, acquired image clarity, pose recovery and compared with an existing model based on simple object recognition and localization.
- 1 December 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 293-298
Vehicle object observation using position based local gradient model
The conception of traffic activities in urban framework is the major endeavor in the study of traffic troubles. This examination is chiefly processed on the maximization of traffic flow, and the minimization of traffic accidents, congestions and pollution. In common, network representations of transport systems are understood to be fixed, but these representations do not permit an exact recreation of seriously packed urban road networks. For this rationale, traffic engineers happened to judge some substitute models such as simple object recognition and localization of road vehicles based on the position and orientation of vehicle image data. But the drawback of the approach is that if the shape of the vehicle and its pose varies in multiple junction coordination, the model based recognition is an inefficient one. To enhance the process of traffic flow mechanism, in this paper, we are going to implement a surveillance image object recognition and localization using improved local gradient model. At first, the vehicle images are taken by camera which is taken on the junction board of the traffic coordination. Based on location, position, angle and height of the camera to be fixed on the junction board, the vehicle images are obtained clearly in an aerial view and extracted the entire road for identifying the vehicle densities and postures using ray traced templates. An experimental evaluation is carried out to estimate the performance of the proposed vehicle object observation using position based local gradient model in terms of vehicle density, acquired image clarity, pose recovery and compared with an existing model based on simple object recognition and localization.