David Jech
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
David Jech has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Ladislav Čelko
CEITEC—Central European Institute of Technology, Brno University of Technology, Purkyňova 123, 612 00 Brno, Czech Republic
4 shared publications - Karel Slámečka
Brno University of Technology
2 shared publications Dagmar Dietrich
Chemnitz University of Technology
1 shared publicationDavid Paloušek
1 shared publicationDušan DOLÁK
1 shared publication- Ivo Šulák
Czech Acad Sci, Inst Phys Mat, Zizkova 22, Brno 61600, Czech Republic
1 shared publication
Latest Publications
- 1 May 2018
- Published by Elsevier in Materials Characterization
- Vol. 139, 347-354
Low cycle fatigue performance of Ni-based superalloy coated with complex thermal barrier coating
- 1 May 2018
- Published by Elsevier in Materials Characterization
- Vol. 139, 347-354
Low cycle fatigue performance of Ni-based superalloy coated with complex thermal barrier coating
- Open Access
- 20 February 2018
- Published by Kaunas University of Technology (KTU) in Materials Science
- Vol. 24 (1) , 29-34-34
The Effect of the Wear of Rotor Pins on Grinding Efficiency in a High-speed Disintegrator
The Effect of the Wear of Rotor Pins on Grinding Efficiency in a High-speed Disintegrator
- 20 February 2018
- Published by Kaunas University of Technology (KTU) in Materials Science
- Vol. 24 (1) , 29-34-34
Open AccessThe Effect of the Wear of Rotor Pins on Grinding Efficiency in a High-speed Disintegrator
The Effect of the Wear of Rotor Pins on Grinding Efficiency in a High-speed Disintegrator
- 27 November 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 270, 230-235
Investigations of Wettability of Wear Resistant Coatings Produced by Atmospheric Plasma Spraying
Changes in fluids contact angle in the interaction with materials surface can play a critical role in enhancement of hydro-machine components and pipelines efficiency and/or service lifetime. However most nowadays used materials and/or coatings are made from polymers or ceramic polymer composites produced by highly sophisticated and/or very expensive techniques. Unfortunately there are a lack of mechanical properties. With the aim to study the role of the surface topography on the water contact angle changes, the representatives of wear resistant coatings (WC10Co4Cr, Cr2O3+5SiO2+3TiO2 and Al2O3) were produced by means of atmospheric plasma spraying. Wettability of the coatings surface was studied by adding the liquid droplet on as sprayed, grinded and polished coating's surface by measuring the changes of its contact angle. To estimate the coatings phase composition and topography XRD technique and optical profilometer were used. The contact angle of water was measured by sessile droplet method. To obtain the complex information of the cross-sectional coatings microstructure the conventional metallographic analysis approaches and optical microscopy were also used.
- 27 November 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 270, 230-235
Investigations of Wettability of Wear Resistant Coatings Produced by Atmospheric Plasma Spraying
Changes in fluids contact angle in the interaction with materials surface can play a critical role in enhancement of hydro-machine components and pipelines efficiency and/or service lifetime. However most nowadays used materials and/or coatings are made from polymers or ceramic polymer composites produced by highly sophisticated and/or very expensive techniques. Unfortunately there are a lack of mechanical properties. With the aim to study the role of the surface topography on the water contact angle changes, the representatives of wear resistant coatings (WC10Co4Cr, Cr2O3+5SiO2+3TiO2 and Al2O3) were produced by means of atmospheric plasma spraying. Wettability of the coatings surface was studied by adding the liquid droplet on as sprayed, grinded and polished coating's surface by measuring the changes of its contact angle. To estimate the coatings phase composition and topography XRD technique and optical profilometer were used. The contact angle of water was measured by sessile droplet method. To obtain the complex information of the cross-sectional coatings microstructure the conventional metallographic analysis approaches and optical microscopy were also used.
- Open Access
- 24 September 2015
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 25 (1-2) , 94-104
Advanced Microscopic Study of Suspension Plasma-Sprayed Zirconia Coatings with Different Microstructures
- 24 September 2015
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 25 (1-2) , 94-104
Open AccessAdvanced Microscopic Study of Suspension Plasma-Sprayed Zirconia Coatings with Different Microstructures
- 1 April 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 782, 567-572
Critical Weak Points of Atmospheric Plasma Sprayed Thermal Barrier Coatings
The 8 wt. % yttria stabilized zirconia top coat (TC) and the CoNiCrAlY bond coat (BC) were sprayed onto the surface of newly developed fine-grained cast polycrystalline nickel-based superalloy Inconel 713LC by means of atmospheric plasma spraying (APS). As-prepared samples were isothermally exposed at the temperature of 1050 °C for 200 hours in an ambient atmosphere. Structural changes in the thermal barrier coatings (TBC) system after thermal exposure were studied by means of scanning electron microscope equipped with an energy dispersive microanalyzer. Critical weak points were identified on both the substrate-bond coat and bond coat-top coat interfaces.
- 1 April 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 782, 567-572
Critical Weak Points of Atmospheric Plasma Sprayed Thermal Barrier Coatings
The 8 wt. % yttria stabilized zirconia top coat (TC) and the CoNiCrAlY bond coat (BC) were sprayed onto the surface of newly developed fine-grained cast polycrystalline nickel-based superalloy Inconel 713LC by means of atmospheric plasma spraying (APS). As-prepared samples were isothermally exposed at the temperature of 1050 °C for 200 hours in an ambient atmosphere. Structural changes in the thermal barrier coatings (TBC) system after thermal exposure were studied by means of scanning electron microscope equipped with an energy dispersive microanalyzer. Critical weak points were identified on both the substrate-bond coat and bond coat-top coat interfaces.