Zhikang Shen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhikang Shen has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- John Z. Wen
Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, Canada
2 shared publications - Adrian P. Gerlich
Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Avenue West, Waterloo, ON N2L 3G1, Canada
1 shared publication Dongxiao Li
1 shared publicationHaiyan Chen
1 shared publicationHongtao Sui
1 shared publication- Huaxia Zhao
AVIC Manufacturing Technology Institute, Beijing 100024, P. R. China
1 shared publication
Latest Publications
- Open Access
- 6 September 2022
- Published by Springer Nature in Research Square
Microstructural characterization and mechanical properties of AlMg alloy fabricated by additive friction stir deposition
This work investigates microstructure characterization and mechanical properties of Aluminum alloy fabricated by additive friction stir deposition (AFSD). Microstructure characterize of the Aluminum alloy 5B70 base material (BM) and build were compared using optical microscope (OM) and electron back scattered diffraction (EBSD). Hardness distribution in the direction perpendicular to the cross-section of deposited area was measured and the pattern was evaluated. Tensile tests were performed on the BM and the deposition using digital image correlation (DIC), and the stress distribution states of the specimens were analyzed in real time. After the tensile tests, the fracture micromorphology was characterized using scanning electron microscope (SEM). The results show that a high degree of recrystallization of the grains in the deposition zone occurs and fine equiaxed grains are formed, which are oriented differently. In tensile tests on the deposition, it was found that the strength of the deposition was significantly lower compared to the BM, but its toughness was significantly higher. And there is a significant anisotropy in the mechanical properties of the deposition.
- 6 September 2022
- Published by Springer Nature in Research Square
Open AccessMicrostructural characterization and mechanical properties of AlMg alloy fabricated by additive friction stir deposition
This work investigates microstructure characterization and mechanical properties of Aluminum alloy fabricated by additive friction stir deposition (AFSD). Microstructure characterize of the Aluminum alloy 5B70 base material (BM) and build were compared using optical microscope (OM) and electron back scattered diffraction (EBSD). Hardness distribution in the direction perpendicular to the cross-section of deposited area was measured and the pattern was evaluated. Tensile tests were performed on the BM and the deposition using digital image correlation (DIC), and the stress distribution states of the specimens were analyzed in real time. After the tensile tests, the fracture micromorphology was characterized using scanning electron microscope (SEM). The results show that a high degree of recrystallization of the grains in the deposition zone occurs and fine equiaxed grains are formed, which are oriented differently. In tensile tests on the deposition, it was found that the strength of the deposition was significantly lower compared to the BM, but its toughness was significantly higher. And there is a significant anisotropy in the mechanical properties of the deposition.
- 1 May 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 279
Al–NiO energetic composites as heat source for joining silicon wafer
- 1 May 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 279
Al–NiO energetic composites as heat source for joining silicon wafer
- 25 June 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 98 (5-8) , 1721-1731
Calculation of welding tool pin width for friction stir welding of thin overlapping sheets
- 25 June 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 98 (5-8) , 1721-1731
Calculation of welding tool pin width for friction stir welding of thin overlapping sheets
- 1 February 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 54, 766-778
Microstructure and mechanical properties of friction spot welded 6061-T4 aluminum alloy
- 1 February 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 54, 766-778
Microstructure and mechanical properties of friction spot welded 6061-T4 aluminum alloy