Nobuteru Tsubouchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Nobuteru Tsubouchi has a total of 129 co-authors. Here are the top co-authors by number of shared publications:
- Akiyoshi Chayahara
National Institute of Advanced Industrial Science and Technology
58 shared publications - Yoshiaki Mokuno
Diamond Materials Team, Advanced Power Electronics Research Center, National Institute of Advanced Industrial Science and Technology 1 , 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577, Japan
36 shared publications Y. Horino
22 shared publicationsYuji Horino
National Institute of Advanced Industrial Science and Technology (AIST) Diamond Research Center 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577, Japan
18 shared publicationsA. Kinomura
17 shared publicationsAtsushi Kinomura
15 shared publications
Latest Publications
- 28 February 2025
- Published by Elsevier in Diamond and Related Materials
- Vol. 154
In-situ microscopic observation of single-crystal diamond during chemical vapor deposition
- 28 February 2025
- Published by Elsevier in Diamond and Related Materials
- Vol. 154
In-situ microscopic observation of single-crystal diamond during chemical vapor deposition
- 5 July 2023
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 23 (8) , 5671-5676
Evaluation of Local Stress Distributions and Dislocations Around Petal Patterns Observed in CVD Single Crystal Diamond Plates
- 5 July 2023
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 23 (8) , 5671-5676
Evaluation of Local Stress Distributions and Dislocations Around Petal Patterns Observed in CVD Single Crystal Diamond Plates
- 30 November 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 117 (22) , 222103
Conversions of a stacking fault to threading dislocations in homoepitaxial diamond growth studied by transmission electron microscopy
In this paper, we present how configurations of stacking faults (SFs) in (001)-oriented single crystal diamond substrates changed and extended in the film during homoepitaxial diamond growth by chemical vapor deposition, which was investigated using transmission electron microscopy. In the early stages of the film growth, the SFs in the substrate converted to threading dislocation (TD) rows along the end of the (111) SF planes appearing on the substrate surface, where the direction of the end of the SFs on the surface was [1-10]-[-110]. These TDs then traveled nearly in the same direction tilted by 10° to [-110] from the [001] direction without divergence, while extending with slight divergence within ∼7° in the [110]-[-1-10] direction. The diffraction contrasts observed under several two-beam conditions demonstrated that the SF in the substrate was intrinsic type and had a (111) slip plane with a displacement vector R=-a/3[111], where a is the lattice constant of diamond. At the same time, all the TDs converted from the SFs were edge type and their Burgers vector was b = a/2[1-10], perpendicular to the [001] direction.
- 30 November 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 117 (22) , 222103
Conversions of a stacking fault to threading dislocations in homoepitaxial diamond growth studied by transmission electron microscopy
In this paper, we present how configurations of stacking faults (SFs) in (001)-oriented single crystal diamond substrates changed and extended in the film during homoepitaxial diamond growth by chemical vapor deposition, which was investigated using transmission electron microscopy. In the early stages of the film growth, the SFs in the substrate converted to threading dislocation (TD) rows along the end of the (111) SF planes appearing on the substrate surface, where the direction of the end of the SFs on the surface was [1-10]-[-110]. These TDs then traveled nearly in the same direction tilted by 10° to [-110] from the [001] direction without divergence, while extending with slight divergence within ∼7° in the [110]-[-1-10] direction. The diffraction contrasts observed under several two-beam conditions demonstrated that the SF in the substrate was intrinsic type and had a (111) slip plane with a displacement vector R=-a/3[111], where a is the lattice constant of diamond. At the same time, all the TDs converted from the SFs were edge type and their Burgers vector was b = a/2[1-10], perpendicular to the [001] direction.
- 1 January 2018
- Published by Elsevier in Diamond and Related Materials
- Vol. 81, 33-37
Growth and characterization of freestanding p+ diamond (100) substrates prepared by hot-filament chemical vapor deposition
- 1 January 2018
- Published by Elsevier in Diamond and Related Materials
- Vol. 81, 33-37
Growth and characterization of freestanding p+ diamond (100) substrates prepared by hot-filament chemical vapor deposition
- 1 September 2017
- Published by Elsevier in Diamond and Related Materials
- Vol. 78, 44-48
Microstructures of threading dislocation bundles included in CVD homoepitaxial diamond plates
- 1 September 2017
- Published by Elsevier in Diamond and Related Materials
- Vol. 78, 44-48
Microstructures of threading dislocation bundles included in CVD homoepitaxial diamond plates
- 1 December 2016
- Published by Elsevier in Journal of Crystal Growth
- Vol. 455, 71-75
Configuration of a single grown-in dislocation corresponding to one etch pit formed on the surface of CVD homoepitaxial diamond
- 1 December 2016
- Published by Elsevier in Journal of Crystal Growth
- Vol. 455, 71-75
Configuration of a single grown-in dislocation corresponding to one etch pit formed on the surface of CVD homoepitaxial diamond
- 1 March 2016
- Published by Elsevier in Diamond and Related Materials
- Vol. 63, 43-46
Characterizations of etch pits formed on single crystal diamond surface using oxygen/hydrogen plasma surface treatment
- 1 March 2016
- Published by Elsevier in Diamond and Related Materials
- Vol. 63, 43-46
Characterizations of etch pits formed on single crystal diamond surface using oxygen/hydrogen plasma surface treatment