Ján Jobbágy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ján Jobbágy has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
- Koloman Krištof
Institute of Agricultural Engineering, Transport and Bioenergetics, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovakia
15 shared publications - József Zsembeli
National Research Centre for Climate and Regional Land Management, Hungarian University of Agriculture and Life Sciences, Kisújszállási 166, 5300 Karcag, Hungary
5 shared publications - Michal Angelovič
Institute of Agricultural Engineering, Transport and Bioenergetics, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovakia
5 shared publications P. Findura
4 shared publications- Pavol Findura
Department of Machines and Production Biosystems, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovakia
3 shared publications - Tomáš Giertl
Institute of Agricultural Engineering, Transport and Bioenergetics, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovakia
3 shared publications
Latest Publications
- Open Access
- 4 November 2026
- Published by MDPI AG in Preprints.org
Mechanical Performance and Handling Stability of Biochar–Straw Briquettes and Straw–Sunflower Waste–Biochar Pellets
Biochar is a carbon-rich solid with potential as a fuel component, but its friability limits storage and handling. This study evaluated lignocellulosic co-materials for densifying biochar into briquettes and pellets. Briquettes contained straw/biochar ratios of 100/0, 80/20, 60/40 and 40/60; pellets contained straw/biochar/sunflower-waste ratios of 80/0/20, 60/20/20, 40/40/20 and 20/60/20. Mixture moisture was 5.88–6.81% on a wet basis. Peak compressive force was determined from five briquettes and ten pellets per formulation, and retained mass was measured during abrasion. Briquette peak force was greatest at 80/20 straw/biochar (633.02 ± 173.20 N); the formulation effect was significant by Welch ANOVA (p = 0.024) and Kruskal–Wallis testing (p = 0.004). This formulation remained 67.17% mass after 5 min. Pellet peak force was greatest at 60/20/20 straw/biochar/sunflower waste (1130.81 ± 203.69 N). Pellet data were non-normal at 60% biochar; Welch ANOVA was non-significant (p = 0.085), whereas the Kruskal–Wallis test was significant (p = 0.027). Pellet retained mass after 10 min. decreased from 96.19% without biochar to 90.84, 75.80 and 61.40% at 20, 40 and 60% biochar, respectively. A 20% biochar fraction provided the best mechanical compromise. Energy performance requires separate calorimetric and combustion verification.
- 4 November 2026
- Published by MDPI AG in Preprints.org
Open AccessMechanical Performance and Handling Stability of Biochar–Straw Briquettes and Straw–Sunflower Waste–Biochar Pellets
Biochar is a carbon-rich solid with potential as a fuel component, but its friability limits storage and handling. This study evaluated lignocellulosic co-materials for densifying biochar into briquettes and pellets. Briquettes contained straw/biochar ratios of 100/0, 80/20, 60/40 and 40/60; pellets contained straw/biochar/sunflower-waste ratios of 80/0/20, 60/20/20, 40/40/20 and 20/60/20. Mixture moisture was 5.88–6.81% on a wet basis. Peak compressive force was determined from five briquettes and ten pellets per formulation, and retained mass was measured during abrasion. Briquette peak force was greatest at 80/20 straw/biochar (633.02 ± 173.20 N); the formulation effect was significant by Welch ANOVA (p = 0.024) and Kruskal–Wallis testing (p = 0.004). This formulation remained 67.17% mass after 5 min. Pellet peak force was greatest at 60/20/20 straw/biochar/sunflower waste (1130.81 ± 203.69 N). Pellet data were non-normal at 60% biochar; Welch ANOVA was non-significant (p = 0.085), whereas the Kruskal–Wallis test was significant (p = 0.027). Pellet retained mass after 10 min. decreased from 96.19% without biochar to 90.84, 75.80 and 61.40% at 20, 40 and 60% biochar, respectively. A 20% biochar fraction provided the best mechanical compromise. Energy performance requires separate calorimetric and combustion verification.
- Open Access
Exploratory Pilot-Scale Pyrolysis of Paulownia Wood Chips: Product Recovery and Operational Behavior
Pilot-scale pyrolysis requires joint assessment of product recovery and operational behavior. This exploratory study reanalyzed three Paulownia wood-chip runs at nominal setpoints of 300, 400 and 500 °C in a five-section reactor. Each condition processed a reported 20 kg wet-feed charge. Five-second timestamps defined a common 60 min window with 721 observations per run. Recovered solid masses were 7.3, 7.4 and 5.8 kg, and condensate masses were 9.1, 8.3 and 6.6 kg. Combined recoveries were 82.0, 78.5 and 62.0% of wet feed. Unadjusted gas-flow means were 1.757, 3.380 and 8.444 m3·h−1, conditional on an undocumented flowmeter reference state. Temperature-channel d10 means 302.94, 398.43 and 497.72 °C. Elemental analysis revealed a substantial enrichment of carbon content in biochar, increasing from 46.2 wt.% in raw Paulownia biomass to a maximum of 76.99 wt.% at 400 °C. Concurrently, organic dry matter content decreased with increasing temperature due to progressive devolatilizations and ash concentration. The findings confirm that Paulownia biomass can be efficiently valorized through pyrolysis into products suitable for renewable energy production, carbon sequestration and agricultural and environmental applications, supporting its integration into circular bioeconomy systems.
Open AccessExploratory Pilot-Scale Pyrolysis of Paulownia Wood Chips: Product Recovery and Operational Behavior
Pilot-scale pyrolysis requires joint assessment of product recovery and operational behavior. This exploratory study reanalyzed three Paulownia wood-chip runs at nominal setpoints of 300, 400 and 500 °C in a five-section reactor. Each condition processed a reported 20 kg wet-feed charge. Five-second timestamps defined a common 60 min window with 721 observations per run. Recovered solid masses were 7.3, 7.4 and 5.8 kg, and condensate masses were 9.1, 8.3 and 6.6 kg. Combined recoveries were 82.0, 78.5 and 62.0% of wet feed. Unadjusted gas-flow means were 1.757, 3.380 and 8.444 m3·h−1, conditional on an undocumented flowmeter reference state. Temperature-channel d10 means 302.94, 398.43 and 497.72 °C. Elemental analysis revealed a substantial enrichment of carbon content in biochar, increasing from 46.2 wt.% in raw Paulownia biomass to a maximum of 76.99 wt.% at 400 °C. Concurrently, organic dry matter content decreased with increasing temperature due to progressive devolatilizations and ash concentration. The findings confirm that Paulownia biomass can be efficiently valorized through pyrolysis into products suitable for renewable energy production, carbon sequestration and agricultural and environmental applications, supporting its integration into circular bioeconomy systems.
- Open Access
- 2 October 2026
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
Variability of Selected Physical and Mechanical Properties of Soil in Alfalfa Crop Production
In recent years, studies have focused on monitoring soil compaction caused by agriculture. The aim of the research presented in this article was to examine the impact of forage cultivation (organic farming) on soil properties. Field measurements focused on monitoring the variability of soil moisture content (SMC) and penetrometric resistance (PR) during alfalfa cultivation across 3 soil horizons. The study area was a 47.64-hectare plot (Oponice, Slovak Republic) with a total of 21 monitoring points (MP). Standardized methodologies and measurement techniques were used to monitor soil properties (WET sensor with HH2 logger, Eikelkamp penetrometer). Statistical evaluation of the results was performed using descriptive statistics, one-way ANOVA, deterministic spline interpolation (ArcGIS 10.0), and cluster analysis (Orange). The results for soil moisture content indicate significant changes in variability (horizons, dates). The coefficient of variation (CV) values for soil moisture content ranged from 8.47% to 23.12%. A significant depth dependence of the measurements was observed (pilot measurements: P<0.05, F=7.51). An examination of the relationship between individual measurement periods showed that in selected horizons they were dependent (SMC01→SMC02, 0-20 cm, 21-40 cm; SMC02→SMC03, all horizons) and in the others they were independent (SMC01→SMC02, 41-60 cm). The average PR values showed the lowest heterogeneity in the deep soil horizon (CV: PR01, 59.81→16.52%; PR02, 41.97→31.25%; PR03, 38.86→21.22%). Comparisons of measured penetrometer resistance values between irrigated and non-irrigated areas or between different measurement dates showed weak to strong correlations (0.02-0.87; 1.68 to 2.72 MPa). The obtained results were also subjected to deterministic and cluster analyses of penetrometric resistance, with the results indicating significance among the measurements. The results obtained from soil moisture monitoring indicate that soil moisture levels are balanced, but there are negative effects on soil compaction.
- 2 October 2026
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
Open AccessVariability of Selected Physical and Mechanical Properties of Soil in Alfalfa Crop Production
In recent years, studies have focused on monitoring soil compaction caused by agriculture. The aim of the research presented in this article was to examine the impact of forage cultivation (organic farming) on soil properties. Field measurements focused on monitoring the variability of soil moisture content (SMC) and penetrometric resistance (PR) during alfalfa cultivation across 3 soil horizons. The study area was a 47.64-hectare plot (Oponice, Slovak Republic) with a total of 21 monitoring points (MP). Standardized methodologies and measurement techniques were used to monitor soil properties (WET sensor with HH2 logger, Eikelkamp penetrometer). Statistical evaluation of the results was performed using descriptive statistics, one-way ANOVA, deterministic spline interpolation (ArcGIS 10.0), and cluster analysis (Orange). The results for soil moisture content indicate significant changes in variability (horizons, dates). The coefficient of variation (CV) values for soil moisture content ranged from 8.47% to 23.12%. A significant depth dependence of the measurements was observed (pilot measurements: P<0.05, F=7.51). An examination of the relationship between individual measurement periods showed that in selected horizons they were dependent (SMC01→SMC02, 0-20 cm, 21-40 cm; SMC02→SMC03, all horizons) and in the others they were independent (SMC01→SMC02, 41-60 cm). The average PR values showed the lowest heterogeneity in the deep soil horizon (CV: PR01, 59.81→16.52%; PR02, 41.97→31.25%; PR03, 38.86→21.22%). Comparisons of measured penetrometer resistance values between irrigated and non-irrigated areas or between different measurement dates showed weak to strong correlations (0.02-0.87; 1.68 to 2.72 MPa). The obtained results were also subjected to deterministic and cluster analyses of penetrometric resistance, with the results indicating significance among the measurements. The results obtained from soil moisture monitoring indicate that soil moisture levels are balanced, but there are negative effects on soil compaction.
- Open Access
- 1 October 2026
- Published by MDPI AG in Preprints.org
Pilot-Scale Pyrolysis of Paulownia Wood Chips: Effects of Temperature on Product Recovery, Biochar Fuel Properties, and Non-Condensable Gas Flow
The conversion of fast-growing non-food woody biomass into storable fuels and carbon-rich products may contribute to the diversification of regional renewable-resource systems. This exploratory pilot-scale study evaluated Paulownia wood chips in a continuously fed five-zone pyrolysis reactor at setpoint temperatures of 300, 400, and 500 °C. One 20 kg wet-feed run was evaluated at each setpoint at a nominal throughput of 20 kg h⁻¹ and a nominal residence time of 10 min. Reactor temperature, non-condensable gas volumetric flow, and electrical input power were recorded at 5 s intervals. Recovered biochar masses were 7.3, 7.4, and 5.8 kg, and recovered condensed-liquid masses were 9.1, 8.3, and 6.6 kg at 300, 400, and 500 °C, respectively. The combined solid-plus-liquid recovery decreased from 82.0 to 62.0% of wet feed. Because gas mass and composition were not measured, the remaining fraction cannot be interpreted as a gas yield, and a closed mass balance was not established. Mean non-condensable gas flow rates calculated from the time-series data were 1.65, 3.53, and 8.36 m³ h⁻¹, while mean measured reactor temperatures were 303.1, 398.5, and 498.0 °C. The highest observed carbon content and higher heating value of biochar occurred at 400 °C, at 76.99 wt.% and 30.47 MJ kg⁻¹. The calculated atomic H/C ratio decreased from 0.68 at 300 °C to 0.37 at 500 °C. The results describe temperature-dependent behaviour in one pilot-scale run per condition and do not provide inferential evidence of an optimum. Replicated reactor runs, gas chromatography, liquid-phase analysis, and expanded biochar characterisation are required before process efficiency or application suitability can be established.
- 1 October 2026
- Published by MDPI AG in Preprints.org
Open AccessPilot-Scale Pyrolysis of Paulownia Wood Chips: Effects of Temperature on Product Recovery, Biochar Fuel Properties, and Non-Condensable Gas Flow
The conversion of fast-growing non-food woody biomass into storable fuels and carbon-rich products may contribute to the diversification of regional renewable-resource systems. This exploratory pilot-scale study evaluated Paulownia wood chips in a continuously fed five-zone pyrolysis reactor at setpoint temperatures of 300, 400, and 500 °C. One 20 kg wet-feed run was evaluated at each setpoint at a nominal throughput of 20 kg h⁻¹ and a nominal residence time of 10 min. Reactor temperature, non-condensable gas volumetric flow, and electrical input power were recorded at 5 s intervals. Recovered biochar masses were 7.3, 7.4, and 5.8 kg, and recovered condensed-liquid masses were 9.1, 8.3, and 6.6 kg at 300, 400, and 500 °C, respectively. The combined solid-plus-liquid recovery decreased from 82.0 to 62.0% of wet feed. Because gas mass and composition were not measured, the remaining fraction cannot be interpreted as a gas yield, and a closed mass balance was not established. Mean non-condensable gas flow rates calculated from the time-series data were 1.65, 3.53, and 8.36 m³ h⁻¹, while mean measured reactor temperatures were 303.1, 398.5, and 498.0 °C. The highest observed carbon content and higher heating value of biochar occurred at 400 °C, at 76.99 wt.% and 30.47 MJ kg⁻¹. The calculated atomic H/C ratio decreased from 0.68 at 300 °C to 0.37 at 500 °C. The results describe temperature-dependent behaviour in one pilot-scale run per condition and do not provide inferential evidence of an optimum. Replicated reactor runs, gas chromatography, liquid-phase analysis, and expanded biochar characterisation are required before process efficiency or application suitability can be established.
- Open Access
- 26 February 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (5) , 2253
Monitoring the Variability of Soil Infiltration Capacity in Irrigated Feed Crop Production
When cultivating a selected field crop (alfalfa), we aimed to examine its positive effects on the variability of soil infiltration capacity. A total of 21 monitoring points were proposed for investigating soil hydraulic conductivity on the targeted plot with a total area of 47.64 ha, divided between the irrigated and non-irrigated areas. The plot is located outside the village of Oponice (Slovak Republic) and is managed by VPP Kolíňany. The study of hydraulic conductivity has been ongoing on the selected plot for several years. The presented results come from a two-year experiment, during which work operations related to the cultivation of alfalfa were carried out on the plot. The unsaturated hydraulic conductivity of the soil was assessed several times a year using a Mini Disk Infiltrometer, while soil moisture at monitoring points and the dependence of the measurement date (work operations, weather conditions) were also monitored. The average soil moisture content in the pilot measurements reached 18.77% vol. (CV = 1.44%), in the secondary measurements 17.21% vol. (CV 20.49%), in tertiary measurements 15.27% vol. (CV = 10.38%), and in the last measurements 15.26% vol. (CV = 10%), which ultimately represents a positive result of soil moisture balance. To test the significance of the differences between measurements taken across the entire surveyed plot, a one-factor ANOVA analysis was used to compare the measurement dates. The results showed a statistically significant difference when examining the effect of the time period of soil infiltration capacity monitoring between all measurements (p = 0.004). The mutual combinations of individual measurement dates were mostly significant (p = 0.03 for IDM1, IDM2; p = 0.003 for IDM2, IDM3), except for one case without a significant difference (IDM3, IDM4; p = 0.52). The second hypothesis was confirmed only at some monitoring points, and it can be stated that the irrigated area had a more significant effect on the soil infiltration capacity. The results obtained by the Shapiro–Wilk test and Welch’s test in irrigated and non-irrigated areas at individual dates showed statistically insignificant differences in three cases (IDM1, p = 0.123; IDM3, p = 0.382; IDM4, p = 0.445) and statistically significant in one case (IDM2, p = 0.0175). Based on the hypotheses and the results obtained, it can be said that the work tasks performed have a decisive influence on the infiltration capacity of the soil. The phenomenon of “water resistance” did not manifest itself in our research on soil infiltration capacity. The results were also evaluated using ArcGIS software 10.0 to display the spatial variability of soil hydraulic conductivity. The last application used to evaluate the results was Orange software 3.40.0, using clustering maps and hierarchical clustering. The results also pointed to variability depending on the dates of monitoring.
- 26 February 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (5) , 2253
Open AccessMonitoring the Variability of Soil Infiltration Capacity in Irrigated Feed Crop Production
When cultivating a selected field crop (alfalfa), we aimed to examine its positive effects on the variability of soil infiltration capacity. A total of 21 monitoring points were proposed for investigating soil hydraulic conductivity on the targeted plot with a total area of 47.64 ha, divided between the irrigated and non-irrigated areas. The plot is located outside the village of Oponice (Slovak Republic) and is managed by VPP Kolíňany. The study of hydraulic conductivity has been ongoing on the selected plot for several years. The presented results come from a two-year experiment, during which work operations related to the cultivation of alfalfa were carried out on the plot. The unsaturated hydraulic conductivity of the soil was assessed several times a year using a Mini Disk Infiltrometer, while soil moisture at monitoring points and the dependence of the measurement date (work operations, weather conditions) were also monitored. The average soil moisture content in the pilot measurements reached 18.77% vol. (CV = 1.44%), in the secondary measurements 17.21% vol. (CV 20.49%), in tertiary measurements 15.27% vol. (CV = 10.38%), and in the last measurements 15.26% vol. (CV = 10%), which ultimately represents a positive result of soil moisture balance. To test the significance of the differences between measurements taken across the entire surveyed plot, a one-factor ANOVA analysis was used to compare the measurement dates. The results showed a statistically significant difference when examining the effect of the time period of soil infiltration capacity monitoring between all measurements (p = 0.004). The mutual combinations of individual measurement dates were mostly significant (p = 0.03 for IDM1, IDM2; p = 0.003 for IDM2, IDM3), except for one case without a significant difference (IDM3, IDM4; p = 0.52). The second hypothesis was confirmed only at some monitoring points, and it can be stated that the irrigated area had a more significant effect on the soil infiltration capacity. The results obtained by the Shapiro–Wilk test and Welch’s test in irrigated and non-irrigated areas at individual dates showed statistically insignificant differences in three cases (IDM1, p = 0.123; IDM3, p = 0.382; IDM4, p = 0.445) and statistically significant in one case (IDM2, p = 0.0175). Based on the hypotheses and the results obtained, it can be said that the work tasks performed have a decisive influence on the infiltration capacity of the soil. The phenomenon of “water resistance” did not manifest itself in our research on soil infiltration capacity. The results were also evaluated using ArcGIS software 10.0 to display the spatial variability of soil hydraulic conductivity. The last application used to evaluate the results was Orange software 3.40.0, using clustering maps and hierarchical clustering. The results also pointed to variability depending on the dates of monitoring.
- Open Access
- 1 September 2024
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 27 (3) , 157-164
Effect of Scraping on Humus Content of Heavy Textured Soil Degraded by Excess Waters
On low-lying soils with a high clay content and poor water conductivity, excess water regularly appears after almost every rainy winter causing soil degradation, which leads to yield failures and/or losses. To outlet the harmful excess surface, waters needs appropriate ameliorative and agrotechnical operations. Among them, scraping represents a suitable intervention into soil structure involving the complete conversion of the micro-topography of the land. The humus content of the soil is a determining factor in terms of soil fertility; therefore, it must be preserved even when drastic tillage operations are carried out on a plot. Our research aimed to assess the effect of scraping on the humus content of the soil on three plots with a heavy textured Vertisol endangered by excess waters. Scraping was used on these plots to create a homogeneous topography and surface with a slight slope to get rid of excess water when it appears. It was established that scraping did not cause humus loss on a plot scale, and it resulted in an evener organic matter distribution, hence a potentially more homogenous yield within the ameliorated plots.
- 1 September 2024
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 27 (3) , 157-164
Open AccessEffect of Scraping on Humus Content of Heavy Textured Soil Degraded by Excess Waters
On low-lying soils with a high clay content and poor water conductivity, excess water regularly appears after almost every rainy winter causing soil degradation, which leads to yield failures and/or losses. To outlet the harmful excess surface, waters needs appropriate ameliorative and agrotechnical operations. Among them, scraping represents a suitable intervention into soil structure involving the complete conversion of the micro-topography of the land. The humus content of the soil is a determining factor in terms of soil fertility; therefore, it must be preserved even when drastic tillage operations are carried out on a plot. Our research aimed to assess the effect of scraping on the humus content of the soil on three plots with a heavy textured Vertisol endangered by excess waters. Scraping was used on these plots to create a homogeneous topography and surface with a slight slope to get rid of excess water when it appears. It was established that scraping did not cause humus loss on a plot scale, and it resulted in an evener organic matter distribution, hence a potentially more homogenous yield within the ameliorated plots.
- Open Access
- 1 June 2024
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 27 (2) , 116-124
Impact of Machinery Passages on Soil Compaction in Field Conditions
The present study compares the consequences of soil compaction due to machinery in a selected 13.7 ha plot at Hronské Kosihy (Slovak Republic). The crop was winter wheat, while the changes of selected soil properties (penetration resistance and gravimetric soil water content) were monitored. The experimental plot was divided into 11 zones with different initial status of compaction: one of them was the reference zone without compaction (P1), five zones were out of the track line, four were directly in the track lines, and one was a collection route. The number of passages in each zone was from 0 up to more than 15. The impact of the number of machinery passages on gravimetric soil water content was found significant both in and out of the track lines with an average value of 17.37%. The monitoring of the passage number showed to be important also in the monitoring of soil penetration resistance ( P P <0.05) was identified by the assessment and comparison of individual impacts of passages in the track zones (P3, P4, P6, and P7). A similar scenario was found also in case of the dependence of soil compaction on the passages monitored off the track lines (P2, P5). Also, the change of tire pressure was statistically significant, its decrease from 0.19 to 0.15 MPa showed to be beneficial. The highest compaction was monitored in the passages in P11 with an average value of 5.36 MPa, representing 2.3 times higher values than the reference one. The creation of a collection line enables reducing the compaction of the entire plot. The collection line should cover only a very small part of the plot.
- 1 June 2024
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 27 (2) , 116-124
Open AccessImpact of Machinery Passages on Soil Compaction in Field Conditions
The present study compares the consequences of soil compaction due to machinery in a selected 13.7 ha plot at Hronské Kosihy (Slovak Republic). The crop was winter wheat, while the changes of selected soil properties (penetration resistance and gravimetric soil water content) were monitored. The experimental plot was divided into 11 zones with different initial status of compaction: one of them was the reference zone without compaction (P1), five zones were out of the track line, four were directly in the track lines, and one was a collection route. The number of passages in each zone was from 0 up to more than 15. The impact of the number of machinery passages on gravimetric soil water content was found significant both in and out of the track lines with an average value of 17.37%. The monitoring of the passage number showed to be important also in the monitoring of soil penetration resistance ( P P <0.05) was identified by the assessment and comparison of individual impacts of passages in the track zones (P3, P4, P6, and P7). A similar scenario was found also in case of the dependence of soil compaction on the passages monitored off the track lines (P2, P5). Also, the change of tire pressure was statistically significant, its decrease from 0.19 to 0.15 MPa showed to be beneficial. The highest compaction was monitored in the passages in P11 with an average value of 5.36 MPa, representing 2.3 times higher values than the reference one. The creation of a collection line enables reducing the compaction of the entire plot. The collection line should cover only a very small part of the plot.
- Open Access
- 11 April 2024
- Published by MDPI AG in Agriengineering
- Vol. 6 (2) , 979-994
Comparative Measurement of Horizontal Penetrometry with a Focus on the Degree of Soil Compaction in Real Work Conditions
Potential soil production is closely related to the physical and mechanical properties. The aim of this paper was to evaluate the effect of different levels of soil compaction created by tractor chassis. The total area of the experimental plot was 13.22 ha. Up until 2019, a conventional tillage system had been used. The measurements were carried out with an innovative measuring device that allows for the continuous measurement of the horizontal penetrometry for comparative measurements while driving, which was designed at the Slovak University of Agriculture in Nitra. The measuring device measured the soil resistance in the tire track (On-track) and out of track (Off-track) as well as in three (50 s) sequences within one tractor pass. Three lines were chosen, where in each a pair of combinations was made. The results were subjected, in addition to graphical evaluation, to single factor ANOVA analysis. When comparing individual passes (PH1 to PH6), the statistical analysis showed that the results of the horizontal resistance measurements proved to be statistically significant (p < 0.05) with respect to the weight, number of passes, and tire underinflation. The highest compaction was caused by the first pass, while the higher weight of the tractor during the next pass had a smaller effect. Underinflating the tires ensured a reduction in compaction. Reducing the tractor tire pressure to 0.15 MPa resulted in a reduction in soil compaction of up to 16%.
- 11 April 2024
- Published by MDPI AG in Agriengineering
- Vol. 6 (2) , 979-994
Open AccessComparative Measurement of Horizontal Penetrometry with a Focus on the Degree of Soil Compaction in Real Work Conditions
Potential soil production is closely related to the physical and mechanical properties. The aim of this paper was to evaluate the effect of different levels of soil compaction created by tractor chassis. The total area of the experimental plot was 13.22 ha. Up until 2019, a conventional tillage system had been used. The measurements were carried out with an innovative measuring device that allows for the continuous measurement of the horizontal penetrometry for comparative measurements while driving, which was designed at the Slovak University of Agriculture in Nitra. The measuring device measured the soil resistance in the tire track (On-track) and out of track (Off-track) as well as in three (50 s) sequences within one tractor pass. Three lines were chosen, where in each a pair of combinations was made. The results were subjected, in addition to graphical evaluation, to single factor ANOVA analysis. When comparing individual passes (PH1 to PH6), the statistical analysis showed that the results of the horizontal resistance measurements proved to be statistically significant (p < 0.05) with respect to the weight, number of passes, and tire underinflation. The highest compaction was caused by the first pass, while the higher weight of the tractor during the next pass had a smaller effect. Underinflating the tires ensured a reduction in compaction. Reducing the tractor tire pressure to 0.15 MPa resulted in a reduction in soil compaction of up to 16%.
- Open Access
- 1 June 2023
- Published by Walter de Gruyter GmbH in Visegrad Journal on Bioeconomy and Sustainable Development
- Vol. 12 (1) , 6-11
Application and Efficiency of Micro Sprinkler Irrigation
In the presented paper, we evaluated the quality of work and the economics of use of irrigation system consisting of micro-sprinklers. The experiment took place on the football field in countryside of southwest Slovakia. The original irrigation system was replaced with a modern one, using a control unit, rainfall sensor, in-ground distribution pipes and micro-sprinklers. The irrigation system consisted of components forming the main and detailed irrigation equipment for irrigating an area of 4,272 m2. The water source was a drilled well with a depth of 80 m. Detailed irrigation equipment consisted of sector micro sprinklers of two types. We monitored 13 rotary micro-sprinklers on the given playground in total. During the measurements, we proceeded according to the international standard ISO 7749-2, while the rain measuring containers were distributed into eight beams. The value of the quality of the work of individual sprinklers, expressed by the coefficient of uniformity of spraying, reached a maximum of 78.18%, but with total coverage it was higher than 90%. Anova statistical analysis did not show a significant dependence of the quality of work on the type of micro-sprinkler (for micro-sprinklers A1, A2 A3: F = 2.95, P >0.05; for micro-sprinklers B, C: F = 0.35, P >0.05). From the viewpoint of evaluating the economic return, the investment proved to return within the period of 4.2 years.
- 1 June 2023
- Published by Walter de Gruyter GmbH in Visegrad Journal on Bioeconomy and Sustainable Development
- Vol. 12 (1) , 6-11
Open AccessApplication and Efficiency of Micro Sprinkler Irrigation
In the presented paper, we evaluated the quality of work and the economics of use of irrigation system consisting of micro-sprinklers. The experiment took place on the football field in countryside of southwest Slovakia. The original irrigation system was replaced with a modern one, using a control unit, rainfall sensor, in-ground distribution pipes and micro-sprinklers. The irrigation system consisted of components forming the main and detailed irrigation equipment for irrigating an area of 4,272 m2. The water source was a drilled well with a depth of 80 m. Detailed irrigation equipment consisted of sector micro sprinklers of two types. We monitored 13 rotary micro-sprinklers on the given playground in total. During the measurements, we proceeded according to the international standard ISO 7749-2, while the rain measuring containers were distributed into eight beams. The value of the quality of the work of individual sprinklers, expressed by the coefficient of uniformity of spraying, reached a maximum of 78.18%, but with total coverage it was higher than 90%. Anova statistical analysis did not show a significant dependence of the quality of work on the type of micro-sprinkler (for micro-sprinklers A1, A2 A3: F = 2.95, P >0.05; for micro-sprinklers B, C: F = 0.35, P >0.05). From the viewpoint of evaluating the economic return, the investment proved to return within the period of 4.2 years.
- Open Access
Evaluation of Soil Infiltration Variability in Compacted and Uncompacted Soil Using Two Devices
Infiltration is defined by the expression of the hydraulic conductivity of the soil, which we decided to monitor on an experimental field applying a modern system of land management (control traffic farming). The present study compared two different methods of monitoring the hydraulic conductivity of soil on a selected 16 ha plot of land in the suburbs of the village Kolíňany (Slovak Republic). During the growing seasons, crops such as oilseed rape, winter wheat, spring barley, winter barley, spring peas, and maize alternated in individual years. In addition to the study of hydraulic conductivity, a long-term experiment is underway to investigate the influence of technogenic factors on soil degradation using a system of controlled movement of machines in the field. A mini disk infiltrometer (method one) was used to evaluate the unsaturated hydraulic conductivity of the soil, and a double ring infiltrometer (method two) was used to measure the saturated hydraulic conductivity. Monitoring changes in soil infiltration capacity within the compacted and uncompacted lines required 26 monitoring points (20 for method one and 6 for method two). The first longitudinal line was compacted by an agricultural machinery chassis, and the second line remained uncompressed. The research also created transverse compacted lines at eight monitoring points (six for method one and two for method two). The results did not show a statistically significant difference when examining the effect of soil infiltration monitoring (compacted p = 0.123; uncompacted p = 0.99). When evaluating the statistical dependence on the compression caused by machinery in the track line, the hypothesis of significance was not confirmed (p = 0.12, at the level of 0.05). However, the results showed variability in the value of the difference factor between the two methods, ranging from 0 to 0.24. On average, it can be concluded that the results achieved using the double ring infiltrometer were 4.16 times higher than those measured with the mini disk infiltrometer. The variability of hydraulic conductivity was demonstrated not only in the compacted but also in the non-compacted part of the plot. In some places, the phenomenon of water repellency appeared, which could be caused by the drier location of the targeted plot.
Open AccessEvaluation of Soil Infiltration Variability in Compacted and Uncompacted Soil Using Two Devices
Infiltration is defined by the expression of the hydraulic conductivity of the soil, which we decided to monitor on an experimental field applying a modern system of land management (control traffic farming). The present study compared two different methods of monitoring the hydraulic conductivity of soil on a selected 16 ha plot of land in the suburbs of the village Kolíňany (Slovak Republic). During the growing seasons, crops such as oilseed rape, winter wheat, spring barley, winter barley, spring peas, and maize alternated in individual years. In addition to the study of hydraulic conductivity, a long-term experiment is underway to investigate the influence of technogenic factors on soil degradation using a system of controlled movement of machines in the field. A mini disk infiltrometer (method one) was used to evaluate the unsaturated hydraulic conductivity of the soil, and a double ring infiltrometer (method two) was used to measure the saturated hydraulic conductivity. Monitoring changes in soil infiltration capacity within the compacted and uncompacted lines required 26 monitoring points (20 for method one and 6 for method two). The first longitudinal line was compacted by an agricultural machinery chassis, and the second line remained uncompressed. The research also created transverse compacted lines at eight monitoring points (six for method one and two for method two). The results did not show a statistically significant difference when examining the effect of soil infiltration monitoring (compacted p = 0.123; uncompacted p = 0.99). When evaluating the statistical dependence on the compression caused by machinery in the track line, the hypothesis of significance was not confirmed (p = 0.12, at the level of 0.05). However, the results showed variability in the value of the difference factor between the two methods, ranging from 0 to 0.24. On average, it can be concluded that the results achieved using the double ring infiltrometer were 4.16 times higher than those measured with the mini disk infiltrometer. The variability of hydraulic conductivity was demonstrated not only in the compacted but also in the non-compacted part of the plot. In some places, the phenomenon of water repellency appeared, which could be caused by the drier location of the targeted plot.