Arthur Filgueira de Almeida
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arthur Filgueira de Almeida has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Renato Alexandre Costa de Santana
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
16 shared publications - Ana Regina Nascimento Campos
UFCG
13 shared publications - José Anderson Machado Oliveira
Universidade Federal de Campina Grande image/svg+xml
12 shared publications - Josiane Dantas Costa
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
11 shared publications - Danilo Lima Dantas
Universidade Federal Rural de Pernambuco
5 shared publications - Ana Paula Moisés de Sousa
Universidade Federal de Campina Grande
3 shared publications
Latest Publications
- Open Access
- 16 April 2025
- Published by Revista Interfaces: Saude, Humanas e Technologia in Revista Interfaces: Saúde, Humanas E Tecnologia
- Vol. 13 (1) , 5113-5122
TECHNOLOGICAL STUDY AND MONITORING OF THE SURFACE FUNCTIONALIZATION OF THE Ni–Ti SHAPE MEMORY ALLOY WITH POLYMERIC COATING
Ni–Ti shape memory alloys are generally applied to produce orthodontic and orthopedic implants. However, it is essential to highlight that implants may fail due to local inflammation caused by the accumulation of bacteria. Therefore, functionalizing the metal surface with biocompatible polymeric coatings is generally used to avoid implant failure. This article addresses a technological monitoring study of Ni–Ti shape memory alloys with surface functionalized with polymeric coatings, using patents as sources of information. The Questel Orbit® platform was used to collect the information, applying the following keywords as previous search terms: “nickel–titanium”, “Ni–Ti”, “Nitinol”, “Coated”, and “Polymer”. Among the areas of technologies related to the topic, the ones that stood out the most were the systems used to produce advanced biomedical devices for use in medicine, such as stents, plates, pins, and wires applied to orthodontic and orthopedic devices. Therefore, the results of this research show a general overview of the main innovations developed in the area and, therefore, can guide future research focused on developing systems formed by Ni–Ti alloys coated with polymers applied in different technological sectors. Ni–Ti shape memory alloys are generally applied to produce orthodontic and orthopedic implants. However, it is essential to highlight that implants may fail due to local inflammation caused by the accumulation of bacteria. Therefore, functionalizing the metal surface with biocompatible polymeric coatings is generally used to avoid implant failure. This article addresses a technological monitoring study of Ni–Ti shape memory alloys with surface functionalized with polymeric coatings, using patents as sources of information. The Questel Orbit® platform was used to collect the information, applying the following keywords as previous search terms: “nickel–titanium”, “Ni–Ti”, “Nitinol”, “Coated”, and “Polymer”. Among the areas of technologies related to the topic, the ones that stood out the most were the systems used to produce advanced biomedical devices for use in medicine, such as stents, plates, pins, and wires applied to orthodontic and orthopedic devices. Therefore, the results of this research show a general overview of the main innovations developed in the area and, therefore, can guide future research focused on developing systems formed by Ni–Ti alloys coated with polymers applied in different technological sectors.
- 16 April 2025
- Published by Revista Interfaces: Saude, Humanas e Technologia in Revista Interfaces: Saúde, Humanas E Tecnologia
- Vol. 13 (1) , 5113-5122
Open AccessTECHNOLOGICAL STUDY AND MONITORING OF THE SURFACE FUNCTIONALIZATION OF THE Ni–Ti SHAPE MEMORY ALLOY WITH POLYMERIC COATING
Ni–Ti shape memory alloys are generally applied to produce orthodontic and orthopedic implants. However, it is essential to highlight that implants may fail due to local inflammation caused by the accumulation of bacteria. Therefore, functionalizing the metal surface with biocompatible polymeric coatings is generally used to avoid implant failure. This article addresses a technological monitoring study of Ni–Ti shape memory alloys with surface functionalized with polymeric coatings, using patents as sources of information. The Questel Orbit® platform was used to collect the information, applying the following keywords as previous search terms: “nickel–titanium”, “Ni–Ti”, “Nitinol”, “Coated”, and “Polymer”. Among the areas of technologies related to the topic, the ones that stood out the most were the systems used to produce advanced biomedical devices for use in medicine, such as stents, plates, pins, and wires applied to orthodontic and orthopedic devices. Therefore, the results of this research show a general overview of the main innovations developed in the area and, therefore, can guide future research focused on developing systems formed by Ni–Ti alloys coated with polymers applied in different technological sectors. Ni–Ti shape memory alloys are generally applied to produce orthodontic and orthopedic implants. However, it is essential to highlight that implants may fail due to local inflammation caused by the accumulation of bacteria. Therefore, functionalizing the metal surface with biocompatible polymeric coatings is generally used to avoid implant failure. This article addresses a technological monitoring study of Ni–Ti shape memory alloys with surface functionalized with polymeric coatings, using patents as sources of information. The Questel Orbit® platform was used to collect the information, applying the following keywords as previous search terms: “nickel–titanium”, “Ni–Ti”, “Nitinol”, “Coated”, and “Polymer”. Among the areas of technologies related to the topic, the ones that stood out the most were the systems used to produce advanced biomedical devices for use in medicine, such as stents, plates, pins, and wires applied to orthodontic and orthopedic devices. Therefore, the results of this research show a general overview of the main innovations developed in the area and, therefore, can guide future research focused on developing systems formed by Ni–Ti alloys coated with polymers applied in different technological sectors.
- Open Access
Electrochemical Fabrication of Ni–Co Alloy over a Wide pH Range Using Sodium Citrate as a Complexing Agent
In this study, nickel–cobalt (Ni–Co) coatings were fabricated via electrodeposition using a 22 central composite factorial design with two central and two axial points, totaling ten experiments. The effects of pH and current density on the coatings’ chemical composition and properties were evaluated. Coatings were characterized by microstructure, morphology, magnetic properties, and corrosion resistance. The results showed that pH significantly influenced chemical composition, while current density had no notable effect. Acidic pH produced cobalt-rich coatings (43–81 at.%), with uniform morphology, higher saturation magnetization, and lower corrosion resistance. Maximum cobalt content (81 at.%) resulted in a mixed face-centered cubic (fcc) + hexagonal close-packed (hcp) phase. Alkaline pH yielded nickel-rich coatings (89–95 at.%), featuring nodular morphology, lower magnetization, higher corrosion resistance, and, exclusively, the fcc phase. The highest polarization resistance (66.1 kΩ) occurred at pH 8.83 and 60 mA/cm2, while resistance decreased with increasing cobalt content. The pH effect on deposition was linked to the formation of citrate complexes: ammonia and citrate complexes promoted nickel deposition under alkaline conditions, while stable cobalt complexes dominated in an acidic pH. These findings highlight the potential to tailor Ni–Co coatings for applications such as corrosion-resistant coatings (nickel-rich) or magnetic devices (cobalt-rich).
Open AccessElectrochemical Fabrication of Ni–Co Alloy over a Wide pH Range Using Sodium Citrate as a Complexing Agent
In this study, nickel–cobalt (Ni–Co) coatings were fabricated via electrodeposition using a 22 central composite factorial design with two central and two axial points, totaling ten experiments. The effects of pH and current density on the coatings’ chemical composition and properties were evaluated. Coatings were characterized by microstructure, morphology, magnetic properties, and corrosion resistance. The results showed that pH significantly influenced chemical composition, while current density had no notable effect. Acidic pH produced cobalt-rich coatings (43–81 at.%), with uniform morphology, higher saturation magnetization, and lower corrosion resistance. Maximum cobalt content (81 at.%) resulted in a mixed face-centered cubic (fcc) + hexagonal close-packed (hcp) phase. Alkaline pH yielded nickel-rich coatings (89–95 at.%), featuring nodular morphology, lower magnetization, higher corrosion resistance, and, exclusively, the fcc phase. The highest polarization resistance (66.1 kΩ) occurred at pH 8.83 and 60 mA/cm2, while resistance decreased with increasing cobalt content. The pH effect on deposition was linked to the formation of citrate complexes: ammonia and citrate complexes promoted nickel deposition under alkaline conditions, while stable cobalt complexes dominated in an acidic pH. These findings highlight the potential to tailor Ni–Co coatings for applications such as corrosion-resistant coatings (nickel-rich) or magnetic devices (cobalt-rich).
- Open Access
Influence of Centerline Segregation Region on the Hydrogen Embrittlement Susceptibility of API 5L X80 Pipeline Steels
The influence of the centerline segregation region (CSR) on the hydrogen embrittlement (HE) of two different API 5L X80 pipeline steel plates was investigated. The novelty of this work was to establish relationships between the CSR, microstructure, and distribution of localized fragile particles on HE susceptibility and on fracture morphology. This work intended to establish a relationship between centerline segregation and HE susceptibility in high-strength low-alloy steels submitted to inhomogeneous transformations. Microscopy, hydrogen permeation, and slow strain rate (SSR) tests were used to investigate hydrogen-related degradation. The solution used on the charging cell of the permeation tests—and on the SSR test cell—was 0.5 mol L−1 H2SO4 + 10 mg L−1 As2O3, and in the oxidation cell, 0.1 M NaOH was used as a solution. The CSR led the thicker plate to present the highest HE index (0.612) in analyses carried out in the mid-thickness; however, the same plate showed the lowest HE index in near-surface tests. The presence of hydrogen changed the fracture morphology from ductile to a brittle and ductile feature; this occurred due to the interaction with localized fragile particles and the significant reduction of the shear stress necessary for the dislocation movement.
Open AccessInfluence of Centerline Segregation Region on the Hydrogen Embrittlement Susceptibility of API 5L X80 Pipeline Steels
The influence of the centerline segregation region (CSR) on the hydrogen embrittlement (HE) of two different API 5L X80 pipeline steel plates was investigated. The novelty of this work was to establish relationships between the CSR, microstructure, and distribution of localized fragile particles on HE susceptibility and on fracture morphology. This work intended to establish a relationship between centerline segregation and HE susceptibility in high-strength low-alloy steels submitted to inhomogeneous transformations. Microscopy, hydrogen permeation, and slow strain rate (SSR) tests were used to investigate hydrogen-related degradation. The solution used on the charging cell of the permeation tests—and on the SSR test cell—was 0.5 mol L−1 H2SO4 + 10 mg L−1 As2O3, and in the oxidation cell, 0.1 M NaOH was used as a solution. The CSR led the thicker plate to present the highest HE index (0.612) in analyses carried out in the mid-thickness; however, the same plate showed the lowest HE index in near-surface tests. The presence of hydrogen changed the fracture morphology from ductile to a brittle and ductile feature; this occurred due to the interaction with localized fragile particles and the significant reduction of the shear stress necessary for the dislocation movement.
- 2 January 2024
- Published by Sociedade Brasileira de Quimica (SBQ) in Revista Virtual de Química
- Vol. 16 (4) , 612-619
Magnetic Properties of Nickel-Cobalt Alloys: A Systematic Review of Alloys Obtained by Electrodeposition
- 2 January 2024
- Published by Sociedade Brasileira de Quimica (SBQ) in Revista Virtual de Química
- Vol. 16 (4) , 612-619
Magnetic Properties of Nickel-Cobalt Alloys: A Systematic Review of Alloys Obtained by Electrodeposition
- 1 January 2024
- Published by Sociedade Brasileira de Quimica (SBQ) in Revista Virtual de Química
- Vol. 16 (2) , 327-340
Modificação da Superfície de Ligas com Memória de Forma NiTi com Revestimentos à Base de Quitosana: Uma Breve Revisão na Literatura de Artigos
- 1 January 2024
- Published by Sociedade Brasileira de Quimica (SBQ) in Revista Virtual de Química
- Vol. 16 (2) , 327-340
Modificação da Superfície de Ligas com Memória de Forma NiTi com Revestimentos à Base de Quitosana: Uma Breve Revisão na Literatura de Artigos
- Open Access
Effects of Current Density and Bath Temperature on the Morphological and Anticorrosive Properties of Zn-Ni Alloys
The effect of current density and bath temperature in the electroplating process on resistance to corrosion of Zn-Ni alloys was evaluated in this work. The electrolytic bath consisted of nickel sulfate, zinc sulfate, sodium sulfate, boric acid, and sodium citrate at pH 7.0. The current density was varied in the range 20–80 mA/cm2 and the bath temperature in the range 30–60 °C. Increasing, independently, the current density or the bath temperature increased the nickel content in the obtained alloy, which affected the alloy microstructure, with a predominant γ phase and cauliflower-like morphology. The nickel content in the alloys was in the range 20–42%wt. A synergistic effect between the current density and bath temperature was observed from a design of experiments and response surface models. The maximum resistance to corrosion occurred for the alloy containing 42%wt. nickel. This alloy was obtained at upper levels of current density and bath temperature, presenting a corrosion potential of −0.789 V and polarization resistance of 4136 .cm2.Open AccessEffects of Current Density and Bath Temperature on the Morphological and Anticorrosive Properties of Zn-Ni Alloys
The effect of current density and bath temperature in the electroplating process on resistance to corrosion of Zn-Ni alloys was evaluated in this work. The electrolytic bath consisted of nickel sulfate, zinc sulfate, sodium sulfate, boric acid, and sodium citrate at pH 7.0. The current density was varied in the range 20–80 mA/cm2 and the bath temperature in the range 30–60 °C. Increasing, independently, the current density or the bath temperature increased the nickel content in the obtained alloy, which affected the alloy microstructure, with a predominant γ phase and cauliflower-like morphology. The nickel content in the alloys was in the range 20–42%wt. A synergistic effect between the current density and bath temperature was observed from a design of experiments and response surface models. The maximum resistance to corrosion occurred for the alloy containing 42%wt. nickel. This alloy was obtained at upper levels of current density and bath temperature, presenting a corrosion potential of −0.789 V and polarization resistance of 4136 .cm2. - Open Access
Thermal, Mechanical, and Electrochemical Characterization of Ti50Ni50−XMox Alloys Obtained by Plasma Arc Melting
This study aims to manufacture and characterize titanium and nickel alloys with different molybdenum (Ti–Ni–Mo) contents, focusing on the influence of these additions on the microstructure, mechanical properties, and corrosion resistance. The relevance of this work stems from the lack of research on this specific alloy and the absence of reports in the literature with molybdenum percentages above 2 at.%. Ti50Ni50−XMox alloys were produced by the plasma arc melting method, with six different compositions (x = 0, 0.5, 1, 2, 3, and 4 at.% Mo), and a comprehensive analysis of microstructure, chemical composition, thermal, mechanical, and electrochemical properties was carried out. The results demonstrated significant alterations in the microstructure of the Ni–Ti alloy with the addition of molybdenum presenting several phases, precipitates (TiNi, Ti2Ni), and oxides (Ti4Ni2O, TiO, and TiO3). The stability of the B2 phase increased with molybdenum content, and the monoclinic martensite (B19′) phase was identified only in the Ni–Ti sample. Introducing molybdenum into the Ni–Ti alloy generated the R-phase and shifted the phase transformation peaks to lower temperatures, as differential scanning calorimetry (DSC) indicated. Microhardness and elastic modulus decreased with increasing Mo content, ranging from 494 HV to 272 HV and 74 GPa to 63 GPa, respectively. Corrosion tests revealed increased corrosion resistance with increasing Mo content, reaching a polarization resistance of 2710 kΩ·cm2 and corrosion current of 11.3 µA. Therefore, this study points to Ti–Ni–Mo alloys as potential candidates to increase the range of Ni–Ti alloy applications, mainly in biomaterials, reinforcing its relevance and need in current alloy research.
Open AccessThermal, Mechanical, and Electrochemical Characterization of Ti50Ni50−XMox Alloys Obtained by Plasma Arc Melting
This study aims to manufacture and characterize titanium and nickel alloys with different molybdenum (Ti–Ni–Mo) contents, focusing on the influence of these additions on the microstructure, mechanical properties, and corrosion resistance. The relevance of this work stems from the lack of research on this specific alloy and the absence of reports in the literature with molybdenum percentages above 2 at.%. Ti50Ni50−XMox alloys were produced by the plasma arc melting method, with six different compositions (x = 0, 0.5, 1, 2, 3, and 4 at.% Mo), and a comprehensive analysis of microstructure, chemical composition, thermal, mechanical, and electrochemical properties was carried out. The results demonstrated significant alterations in the microstructure of the Ni–Ti alloy with the addition of molybdenum presenting several phases, precipitates (TiNi, Ti2Ni), and oxides (Ti4Ni2O, TiO, and TiO3). The stability of the B2 phase increased with molybdenum content, and the monoclinic martensite (B19′) phase was identified only in the Ni–Ti sample. Introducing molybdenum into the Ni–Ti alloy generated the R-phase and shifted the phase transformation peaks to lower temperatures, as differential scanning calorimetry (DSC) indicated. Microhardness and elastic modulus decreased with increasing Mo content, ranging from 494 HV to 272 HV and 74 GPa to 63 GPa, respectively. Corrosion tests revealed increased corrosion resistance with increasing Mo content, reaching a polarization resistance of 2710 kΩ·cm2 and corrosion current of 11.3 µA. Therefore, this study points to Ti–Ni–Mo alloys as potential candidates to increase the range of Ni–Ti alloy applications, mainly in biomaterials, reinforcing its relevance and need in current alloy research.
- Open Access
- 14 March 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (6) , 16237-01e
Effect of chitosan–tungsten composite coating obtained by electrophoretic deposition on the corrosion resistance of Ni–Ti alloy in physiological medium
- 14 March 2023
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 9 (6) , 16237-01e
Open AccessEffect of chitosan–tungsten composite coating obtained by electrophoretic deposition on the corrosion resistance of Ni–Ti alloy in physiological medium
- 21 January 2021
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 99 (S1) , S284-S294
Influence of bath composition on the electrodeposition of amorphous Ni‐Mo alloys using potassium‐sodium tartrate as complexing agent
Currently, sodium citrate is the most used complexing agent for electrodeposition of Ni‐Mo coatings, especially for studying the effect of bath temperature and current density on the proprieties of Ni‐Mo coatings. This study evaluates the influence of the concentrations of nickel sulphate and sodium molybdate on the electrodeposition of Ni‐Mo alloys in baths using tartrate as a complexing agent. Electrodepositions were carried out in a two‐electrode cell. A 32 complete factorial design of experiments along with response surface methodology (RSM) was used for the optimization of bath variables for electrodeposition of Ni‐Mo alloys. The coatings obtained were characterized in terms of chemical composition and surface morphology. The chemical composition of the coatings was most influenced by the sodium molybdate concentration. Ni‐Mo coatings of good quality were obtained in potassium‐sodium tartrate baths with Mo content in the range 18‐44 wt%; some results present even higher Mo content than coatings obtained from citrate baths. The coating with the highest Mo content was deposited from the bath with a concentration ratio of nickel sulphate to sodium molybdate of 1:1. Surface morphology varied according to chemical composition, and microcracks were observed for the coating with 41 wt% Mo, for which scanning electron microscopy (SEM) images also show the presence of nodules. The most homogeneous coating surface was obtained at a concentration ratio of nickel sulphate to sodium molybdate of 10:3. X‐ray diffraction analyses have shown that all coatings obtained in this work are amorphous.
- 21 January 2021
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 99 (S1) , S284-S294
Influence of bath composition on the electrodeposition of amorphous Ni‐Mo alloys using potassium‐sodium tartrate as complexing agent
Currently, sodium citrate is the most used complexing agent for electrodeposition of Ni‐Mo coatings, especially for studying the effect of bath temperature and current density on the proprieties of Ni‐Mo coatings. This study evaluates the influence of the concentrations of nickel sulphate and sodium molybdate on the electrodeposition of Ni‐Mo alloys in baths using tartrate as a complexing agent. Electrodepositions were carried out in a two‐electrode cell. A 32 complete factorial design of experiments along with response surface methodology (RSM) was used for the optimization of bath variables for electrodeposition of Ni‐Mo alloys. The coatings obtained were characterized in terms of chemical composition and surface morphology. The chemical composition of the coatings was most influenced by the sodium molybdate concentration. Ni‐Mo coatings of good quality were obtained in potassium‐sodium tartrate baths with Mo content in the range 18‐44 wt%; some results present even higher Mo content than coatings obtained from citrate baths. The coating with the highest Mo content was deposited from the bath with a concentration ratio of nickel sulphate to sodium molybdate of 1:1. Surface morphology varied according to chemical composition, and microcracks were observed for the coating with 41 wt% Mo, for which scanning electron microscopy (SEM) images also show the presence of nodules. The most homogeneous coating surface was obtained at a concentration ratio of nickel sulphate to sodium molybdate of 10:3. X‐ray diffraction analyses have shown that all coatings obtained in this work are amorphous.
- Open Access
- 7 August 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (9) , e457997332
Estudo toxicológico das sementes de Moringa oleifera Lam. utilizando o teste com Artemia salina Leach
A busca por espécies vegetais, sobretudo aquelas que apresentam maiores benefícios econômicos e também sociais vem ganhando ênfase nas pesquisas científicas. Nesse contexto destaca-se a Moringa oleífera Lam., planta originária da Índia e que apresenta diversas aplicações nos setores alimentícios, industriais, medicinais, tratamento de água, dentre outros. Seus frutos são constituídos de vagens que contêm sementes ricas em minerais, vitaminas, proteínas, lipídios, carboidratos, metabólitos secundários e antioxidantes. O presente trabalho teve por objetivo fazer um estudo toxicológico das sementes da M. oleifera Lam. a partir do teste da Artemia salina Leach. Foram preparados dois extratos etanólicos, sendo um a partir das amêndoas e outro apenas com as cascas que as recobrem. Os extratos foram solubilizados em 5 concentrações diferentes. Cada tubo de ensaio continha os extratos em suas respectivas concentrações e 10 A. salina ativas. Após 24 h foi realizada a contagem para determinação da CL50. Os dados obtidos foram analisados a partir de análise PROBIT com uso do software Statistica. A partir das análises realizadas concluiu-se que a nem a amêndoa e nem a casca da semente da M. oleifera Lam. apresentavam toxicidade, uma vez que ambas tiveram valores de CL50 acima de 1000 µg.mL-1, revelando inclusive uma menor toxicidade que outras plantas convencionalmente utilizadas no Brasil, como o endro e a erva doce.
- 7 August 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (9) , e457997332
Open AccessEstudo toxicológico das sementes de Moringa oleifera Lam. utilizando o teste com Artemia salina Leach
A busca por espécies vegetais, sobretudo aquelas que apresentam maiores benefícios econômicos e também sociais vem ganhando ênfase nas pesquisas científicas. Nesse contexto destaca-se a Moringa oleífera Lam., planta originária da Índia e que apresenta diversas aplicações nos setores alimentícios, industriais, medicinais, tratamento de água, dentre outros. Seus frutos são constituídos de vagens que contêm sementes ricas em minerais, vitaminas, proteínas, lipídios, carboidratos, metabólitos secundários e antioxidantes. O presente trabalho teve por objetivo fazer um estudo toxicológico das sementes da M. oleifera Lam. a partir do teste da Artemia salina Leach. Foram preparados dois extratos etanólicos, sendo um a partir das amêndoas e outro apenas com as cascas que as recobrem. Os extratos foram solubilizados em 5 concentrações diferentes. Cada tubo de ensaio continha os extratos em suas respectivas concentrações e 10 A. salina ativas. Após 24 h foi realizada a contagem para determinação da CL50. Os dados obtidos foram analisados a partir de análise PROBIT com uso do software Statistica. A partir das análises realizadas concluiu-se que a nem a amêndoa e nem a casca da semente da M. oleifera Lam. apresentavam toxicidade, uma vez que ambas tiveram valores de CL50 acima de 1000 µg.mL-1, revelando inclusive uma menor toxicidade que outras plantas convencionalmente utilizadas no Brasil, como o endro e a erva doce.