Bagus Nugroho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Bagus Nugroho has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- I. Ketut Aria Pria Utama
Department of Naval Architecture, Faculty of Marine Technology, Institut Teknologi Sepuluh Nopember (ITS), Surabaya 60111, Indonesia
6 shared publications - Rey Chin
University of Adelaide
6 shared publications - Jason P. Monty
University of Melbourne
5 shared publications - Nicholas Hutchins
University of Melbourne
5 shared publications - Bharathram Ganapathisubramani
University of Southampton
3 shared publications - Ketut Suastika
Department of Naval Architecture, Faculty of Marine Technology, Institut Teknologi Sepuluh Nopember, Surabaya 60111, Indonesia
3 shared publications
Latest Publications
- Open Access
- 3 September 2026
- Published by Springer Nature in Experiments in Fluids
- Vol. 67 (10) , 147
Varied average height and area coverage of rough surfaces on turbulent boundary layers
Turbulent boundary layers (TBL) over various area coverages of rough surfaces were studied in a wind tunnel using hot-wire anemometry. The rough surfaces are built by randomly distributed sand grains with an average of 0.7 and 0.9 mm heights, covering 12%, 25%, 38%, 55%, and 75% of the flat-plate surface area. This paper aims to correlate the average roughness height ( k ) and roughness area coverage (RAC) with the Hama roughness function $$\Delta U^+$$ and to explore the influence of these roughness characteristics towards the TBL. The correlation between these roughness variables suggests that as the RAC increases, the $$\Delta U^+$$ increases and reaches a peak value at $$38\%$$ RAC. However, beyond the $$38\%$$ of RAC, the $$\Delta U^+$$ values decrease and then saturate. The mutual sheltering effect at a certain pitch-to-roughness height ratio is suspected to be the underlying mechanism for this pattern. Another finding in this study is that for surfaces with RAC < 100%, the Hama roughness function does not scale with the roughness effective slope. This finding suggests that the RAC is an important factor for any roughness TBL study, especially for surfaces with RAC < 100%. Finally, this study also correlates the two roughness characteristics ( k and RAC) with the fully rough asymptote of Nikuradse (1933) to estimate the associated equivalent sand grain roughness height, $$k_\textrm{s}$$ . The analysis indicates that the majority of the investigated cases are reaching the fully rough condition, and some are in the transitionally rough regime.- 3 September 2026
- Published by Springer Nature in Experiments in Fluids
- Vol. 67 (10) , 147
Open AccessVaried average height and area coverage of rough surfaces on turbulent boundary layers
Turbulent boundary layers (TBL) over various area coverages of rough surfaces were studied in a wind tunnel using hot-wire anemometry. The rough surfaces are built by randomly distributed sand grains with an average of 0.7 and 0.9 mm heights, covering 12%, 25%, 38%, 55%, and 75% of the flat-plate surface area. This paper aims to correlate the average roughness height ( k ) and roughness area coverage (RAC) with the Hama roughness function $$\Delta U^+$$ and to explore the influence of these roughness characteristics towards the TBL. The correlation between these roughness variables suggests that as the RAC increases, the $$\Delta U^+$$ increases and reaches a peak value at $$38\%$$ RAC. However, beyond the $$38\%$$ of RAC, the $$\Delta U^+$$ values decrease and then saturate. The mutual sheltering effect at a certain pitch-to-roughness height ratio is suspected to be the underlying mechanism for this pattern. Another finding in this study is that for surfaces with RAC < 100%, the Hama roughness function does not scale with the roughness effective slope. This finding suggests that the RAC is an important factor for any roughness TBL study, especially for surfaces with RAC < 100%. Finally, this study also correlates the two roughness characteristics ( k and RAC) with the fully rough asymptote of Nikuradse (1933) to estimate the associated equivalent sand grain roughness height, $$k_\textrm{s}$$ . The analysis indicates that the majority of the investigated cases are reaching the fully rough condition, and some are in the transitionally rough regime. - 29 May 2026
- Published by Elsevier in Applied Thermal Engineering
- Vol. 302
Enhancing thermal efficiency in spiral pipes: a review of heat transfer mechanisms and pressure drop
- 29 May 2026
- Published by Elsevier in Applied Thermal Engineering
- Vol. 302
Enhancing thermal efficiency in spiral pipes: a review of heat transfer mechanisms and pressure drop
- Open Access
- 23 March 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1031, A17
Miniature vortex generator control of turbulent boundary layers
Miniature vortex generators (MVGs) are a promising passive flow control technique for viscous drag reduction by producing large-scale vortical motions that manipulate turbulence structures in turbulent boundary layers (TBLs) without significant device drag. This study conducts hot-wire anemometry experiments to investigate the influence of the Reynolds number and the ratio of MVG height $h$ to TBL thickness $\delta _0$ (MVG height ratio $h/\delta _0$ ) on turbulence structures. Experiments encompass two MVG height ratios, $h/\delta _0=0.09,\;0.18$ , friction Reynolds numbers ranging from ${\textit{Re}}_\tau =400$ to 2000 and measure the velocity information at various downstream stations. Spectral analysis confirms the MVG-induced vortices amplify large-scale structures in the outer region, sustaining up to 100 times the MVG height downstream. The MVGs are also found to attenuate turbulence energy across a wide range of turbulence structures below the amplification location in the logarithmic region, connected with the MVG-induced spanwise motion. Increasing the friction Reynolds number from ${\textit{Re}}_\tau =400$ to $900$ or doubling the MVG height ratio causes the amplified structures to develop into longer motions and move away from the wall, while increasing the turbulence energy attenuation proportion to the log region. Moreover, the energy attenuation amplitude of large-scale structures in the near-wall region increases with a larger MVG height ratio but decreases with increasing Reynolds numbers. The findings indicate that, at friction Reynolds numbers ${\textit{Re}}_\tau \geqslant 900$ , MVGs induce spanwise motions that attenuate near-wall structures and modulate large-scale outer motions. The present configuration does not yield a global viscous drag reduction, but the turbulence modulation trends suggest the potential for viscous drag reduction when the MVG configurations are optimised to enhance favourable buffer-layer spanwise motions.- 23 March 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1031, A17
Open AccessMiniature vortex generator control of turbulent boundary layers
Miniature vortex generators (MVGs) are a promising passive flow control technique for viscous drag reduction by producing large-scale vortical motions that manipulate turbulence structures in turbulent boundary layers (TBLs) without significant device drag. This study conducts hot-wire anemometry experiments to investigate the influence of the Reynolds number and the ratio of MVG height $h$ to TBL thickness $\delta _0$ (MVG height ratio $h/\delta _0$ ) on turbulence structures. Experiments encompass two MVG height ratios, $h/\delta _0=0.09,\;0.18$ , friction Reynolds numbers ranging from ${\textit{Re}}_\tau =400$ to 2000 and measure the velocity information at various downstream stations. Spectral analysis confirms the MVG-induced vortices amplify large-scale structures in the outer region, sustaining up to 100 times the MVG height downstream. The MVGs are also found to attenuate turbulence energy across a wide range of turbulence structures below the amplification location in the logarithmic region, connected with the MVG-induced spanwise motion. Increasing the friction Reynolds number from ${\textit{Re}}_\tau =400$ to $900$ or doubling the MVG height ratio causes the amplified structures to develop into longer motions and move away from the wall, while increasing the turbulence energy attenuation proportion to the log region. Moreover, the energy attenuation amplitude of large-scale structures in the near-wall region increases with a larger MVG height ratio but decreases with increasing Reynolds numbers. The findings indicate that, at friction Reynolds numbers ${\textit{Re}}_\tau \geqslant 900$ , MVGs induce spanwise motions that attenuate near-wall structures and modulate large-scale outer motions. The present configuration does not yield a global viscous drag reduction, but the turbulence modulation trends suggest the potential for viscous drag reduction when the MVG configurations are optimised to enhance favourable buffer-layer spanwise motions. - Open Access
- 1 October 2025
- Published by Springer Nature in Research Square
Varied Average Height and Area Coverage of Rough Surfaces on Turbulent Boundary Layers
Turbulent boundary layer (TBL) over various area coverages of rough surfaces was studied in a wind tunnel using hot-wire anemometry. The rough surfaces are built by randomly distributed sand grains with an average of 0.7 and 0.9 mm heights, covering 12%, 25%, 38%, 55%, and 75% of the flat plate surface area. This paper aims to correlate the average roughness height () and roughness area coverage (RAC) with the Hama roughness function + and to explore the influence of these roughness characteristics towards the TBL. The correlation between these roughness variables suggests that as the RAC increases, the + increases and reaches a peak value at 38% roughness area coverage. However, beyond the 38% of RAC, the + values decrease and then saturate. The mutual sheltering effect at a certain pitch-to-roughness height ratio is suspected to be the underlying mechanism for this pattern. Another finding in this report is that for surfaces with RAC < 100%, the Hama roughness function does not scale with the effective slope. This finding suggests that the RAC is an important factor for any roughness TBL study, especially for surfaces with RAC < 100%. Finally, this report also correlates the two roughness characteristics (and RAC) with the fully rough asymptote of [1] to estimate the associated equivalent sand grain roughness height. The analysis indicates that the majority of the investigated cases are reaching the fully rough condition, and some are in the transitionally rough regime.
- 1 October 2025
- Published by Springer Nature in Research Square
Open AccessVaried Average Height and Area Coverage of Rough Surfaces on Turbulent Boundary Layers
Turbulent boundary layer (TBL) over various area coverages of rough surfaces was studied in a wind tunnel using hot-wire anemometry. The rough surfaces are built by randomly distributed sand grains with an average of 0.7 and 0.9 mm heights, covering 12%, 25%, 38%, 55%, and 75% of the flat plate surface area. This paper aims to correlate the average roughness height () and roughness area coverage (RAC) with the Hama roughness function + and to explore the influence of these roughness characteristics towards the TBL. The correlation between these roughness variables suggests that as the RAC increases, the + increases and reaches a peak value at 38% roughness area coverage. However, beyond the 38% of RAC, the + values decrease and then saturate. The mutual sheltering effect at a certain pitch-to-roughness height ratio is suspected to be the underlying mechanism for this pattern. Another finding in this report is that for surfaces with RAC < 100%, the Hama roughness function does not scale with the effective slope. This finding suggests that the RAC is an important factor for any roughness TBL study, especially for surfaces with RAC < 100%. Finally, this report also correlates the two roughness characteristics (and RAC) with the fully rough asymptote of [1] to estimate the associated equivalent sand grain roughness height. The analysis indicates that the majority of the investigated cases are reaching the fully rough condition, and some are in the transitionally rough regime.
- Open Access
- 26 September 2025
- Published by Elsevier in Ocean Engineering
- Vol. 342
The simulation of large-sized pathogen-laden respiratory droplet spread inside a passenger ferry
- 26 September 2025
- Published by Elsevier in Ocean Engineering
- Vol. 342
Open AccessThe simulation of large-sized pathogen-laden respiratory droplet spread inside a passenger ferry
- 6 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 295
An exhaustive review of studies on bio-inspired convergent–divergent riblets
- 6 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 295
An exhaustive review of studies on bio-inspired convergent–divergent riblets
- Open Access
- 13 October 2023
- Published by Springer Nature in Experiments in Fluids
- Vol. 64 (11) , 1-20
Assessment of aerodynamic roughness parameters of turbulent boundary layers over barnacle-covered surfaces
Full-scale drag penalty predictions of flows over rough walls require surface roughness characterisation from laboratory experiments or numerical simulations. In either approach, it is necessary to determine the so-called equivalent sand-grain roughness height ( $$k_s$$ ). There are several steps involved in determining this aerodynamic roughness lengthscale, but its procedure typically includes a combination of measurement of wall-shear stress ( $$\tau _w$$ ) using direct or indirect methods as well as analysis of velocity profiles. Indirect methods usually rely on assumptions made about flow and its scaling including the validity of universal outer-layer similarity. However, the implications of the underlying assumptions involved in full-scale drag prediction are unclear. In this work, we carry out wind tunnel measurements over a realistic rough surface (from a fouled ship-hull) to evaluate the impact of different methods with an emphasis on using the outer-layer similarity hypothesis for full-scale drag predictions. Wall-shear stress is measured using an in-house floating-element drag balance (DB), and velocity profiles are obtained using particle image velocimetry (PIV), allowing the evaluation of $$k_s$$ , and the associated wake parameters through several methods. The aerodynamic roughness parameters hence obtained are used for full-scale drag penalty calculations. It is observed that the predicted drag penalty can vary by over 15 $$\%$$ among the different methods highlighting the care that should be taken when employing such methods.- 13 October 2023
- Published by Springer Nature in Experiments in Fluids
- Vol. 64 (11) , 1-20
Open AccessAssessment of aerodynamic roughness parameters of turbulent boundary layers over barnacle-covered surfaces
Full-scale drag penalty predictions of flows over rough walls require surface roughness characterisation from laboratory experiments or numerical simulations. In either approach, it is necessary to determine the so-called equivalent sand-grain roughness height ( $$k_s$$ ). There are several steps involved in determining this aerodynamic roughness lengthscale, but its procedure typically includes a combination of measurement of wall-shear stress ( $$\tau _w$$ ) using direct or indirect methods as well as analysis of velocity profiles. Indirect methods usually rely on assumptions made about flow and its scaling including the validity of universal outer-layer similarity. However, the implications of the underlying assumptions involved in full-scale drag prediction are unclear. In this work, we carry out wind tunnel measurements over a realistic rough surface (from a fouled ship-hull) to evaluate the impact of different methods with an emphasis on using the outer-layer similarity hypothesis for full-scale drag predictions. Wall-shear stress is measured using an in-house floating-element drag balance (DB), and velocity profiles are obtained using particle image velocimetry (PIV), allowing the evaluation of $$k_s$$ , and the associated wake parameters through several methods. The aerodynamic roughness parameters hence obtained are used for full-scale drag penalty calculations. It is observed that the predicted drag penalty can vary by over 15 $$\%$$ among the different methods highlighting the care that should be taken when employing such methods. - 10 January 2023
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 8 (1) , 014601
Systematic study of the Reynolds number and streamwise spacing effects in two-dimensional square-bar rough-wall turbulent boundary layers
Turbulent boundary layer experiments above a smooth wall and two-dimensional (2D) rod-roughened walls are conducted to investigate the effects of friction Reynolds numbers and streamwise spacing of the roughness elements on the flow properties. The first study uses the roughness pitch to height ratio and a range of friction Reynolds numbers, . The result shows that the drag coefficient converges to the fully rough condition (akin to the classic k-type roughness at a fully developed state) with large roughness Reynolds numbers () when the friction Reynolds number reaches and the relative roughness height is , where is the boundary layer thickness. As increases, the premultiplied energy spectra show that the normalized energy of the near-wall cycle decreases, while the large-scale structures become more dominant. The second study uses a wide range of () at . The and the roughness function results indicate that the increase of streamwise spacing of the roughness elements induces higher and , and it reaches the maximum value at . For , the and values decrease as increases, indicating a less severe drag increase. The premultiplied energy spectra also show that the highly energetic near-wall cycle of streaks and quasistreamwise vortices decreases as increases (for all cases from –128), and they seem to be transported farther from the wall. The trend is slightly different for the largest-scale structures located around the log region. The result suggests that 2D square-bar roughness can reduce the energy distribution for the largest-scale structure for .- 10 January 2023
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 8 (1) , 014601
Systematic study of the Reynolds number and streamwise spacing effects in two-dimensional square-bar rough-wall turbulent boundary layers
Turbulent boundary layer experiments above a smooth wall and two-dimensional (2D) rod-roughened walls are conducted to investigate the effects of friction Reynolds numbers and streamwise spacing of the roughness elements on the flow properties. The first study uses the roughness pitch to height ratio and a range of friction Reynolds numbers, . The result shows that the drag coefficient converges to the fully rough condition (akin to the classic k-type roughness at a fully developed state) with large roughness Reynolds numbers () when the friction Reynolds number reaches and the relative roughness height is , where is the boundary layer thickness. As increases, the premultiplied energy spectra show that the normalized energy of the near-wall cycle decreases, while the large-scale structures become more dominant. The second study uses a wide range of () at . The and the roughness function results indicate that the increase of streamwise spacing of the roughness elements induces higher and , and it reaches the maximum value at . For , the and values decrease as increases, indicating a less severe drag increase. The premultiplied energy spectra also show that the highly energetic near-wall cycle of streaks and quasistreamwise vortices decreases as increases (for all cases from –128), and they seem to be transported farther from the wall. The trend is slightly different for the largest-scale structures located around the log region. The result suggests that 2D square-bar roughness can reduce the energy distribution for the largest-scale structure for .- Open Access
- 28 October 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 951, A1
Impact of spanwise effective slope upon rough-wall turbulent channel flow
Whereas streamwise effective slope ( $ES_{x}$ ) is accepted as a key topographical parameter in the context of rough-wall turbulent flows, the significance of its spanwise counterpart ( $ES_{y}$ ) remains largely unexplored. Here, the response of turbulent channel flow over irregular, three-dimensional rough walls with systematically varied values of $ES_{y}$ is studied using direct numerical simulation. All simulations were performed at a fixed friction Reynolds number 395, corresponding to a viscous-scaled roughness height $k^{+}\approx 65.8$ (where $k$ is the mean peak-to-valley height). A surface generation algorithm is used to synthesise a set of ten irregular surfaces with specified $ES_{y}$ for three different values of $ES_{x}$ . All surfaces share a common mean peak-to-valley height and are near-Gaussian, which allows this study to focus on the impact of varying $ES_{y}$ , since roughness amplitude, skewness and $ES_{x}$ can be eliminated simultaneously as parameters. Based on an analysis of first- and second-order velocity statistics, as well as turbulence co-spectra and the fractional contribution of pressure and viscous drag, the study shows that $ES_{y}$ can strongly affect the roughness drag penalty – particularly for low- $ES_{x}$ surfaces. A secondary observation is that particular low- $ES_{y}$ surfaces in this study can lead to diminished levels of outer-layer similarity in both mean flow and turbulence statistics, which is attributed to insufficient scale separation between the outer length scale and the in-plane spanwise roughness wavelength.- 28 October 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 951, A1
Open AccessImpact of spanwise effective slope upon rough-wall turbulent channel flow
Whereas streamwise effective slope ( $ES_{x}$ ) is accepted as a key topographical parameter in the context of rough-wall turbulent flows, the significance of its spanwise counterpart ( $ES_{y}$ ) remains largely unexplored. Here, the response of turbulent channel flow over irregular, three-dimensional rough walls with systematically varied values of $ES_{y}$ is studied using direct numerical simulation. All simulations were performed at a fixed friction Reynolds number 395, corresponding to a viscous-scaled roughness height $k^{+}\approx 65.8$ (where $k$ is the mean peak-to-valley height). A surface generation algorithm is used to synthesise a set of ten irregular surfaces with specified $ES_{y}$ for three different values of $ES_{x}$ . All surfaces share a common mean peak-to-valley height and are near-Gaussian, which allows this study to focus on the impact of varying $ES_{y}$ , since roughness amplitude, skewness and $ES_{x}$ can be eliminated simultaneously as parameters. Based on an analysis of first- and second-order velocity statistics, as well as turbulence co-spectra and the fractional contribution of pressure and viscous drag, the study shows that $ES_{y}$ can strongly affect the roughness drag penalty – particularly for low- $ES_{x}$ surfaces. A secondary observation is that particular low- $ES_{y}$ surfaces in this study can lead to diminished levels of outer-layer similarity in both mean flow and turbulence statistics, which is attributed to insufficient scale separation between the outer length scale and the in-plane spanwise roughness wavelength. - Open Access
- 21 December 2021
- Published by Karary University in Journal of Karary University for Engineering and Science
Experimental Study of Boundary Layer flow over a Zero Pressure Gradient Convergent Riblet Plate
Reducing the friction force in turbulence flows is an important research topic in fluid mechanics. Shark skin has less drag than smooth skins, therefore shark skin surfaces have been widely used. However, some turbulence mechanisms are not completely understood and the drag reduction mechanism of real shark skin has not been thoroughly understood. Many researchers have experimentally studied bio-inspired riblet surfaces to explain some specified phenomena for the sharkskin drag reduction effect. The objectives of this study were to investigate the effect of the converging-diverging riblet-type surface roughness on a zero pressure gradient turbulent boundary layers, to investigate the effect of the surface roughness on the large-scale features and to confirm that converging-diverging riblet generate large-scale counter-rotating vortices. The wind tunnel experiments involved laminar and turbulent flow at various Re were performed. Hot-wire anemometry was used to investigate near-wall flow structure over smooth and riblet surfaces. The results showed that the convergent riblet plate significantly impacted the boundary layer properties. Furthermore, the turbulent skin friction drag over the convergent riblet was higher than on a smooth surface. The results agree well with previous studies.
- 21 December 2021
- Published by Karary University in Journal of Karary University for Engineering and Science
Open AccessExperimental Study of Boundary Layer flow over a Zero Pressure Gradient Convergent Riblet Plate
Reducing the friction force in turbulence flows is an important research topic in fluid mechanics. Shark skin has less drag than smooth skins, therefore shark skin surfaces have been widely used. However, some turbulence mechanisms are not completely understood and the drag reduction mechanism of real shark skin has not been thoroughly understood. Many researchers have experimentally studied bio-inspired riblet surfaces to explain some specified phenomena for the sharkskin drag reduction effect. The objectives of this study were to investigate the effect of the converging-diverging riblet-type surface roughness on a zero pressure gradient turbulent boundary layers, to investigate the effect of the surface roughness on the large-scale features and to confirm that converging-diverging riblet generate large-scale counter-rotating vortices. The wind tunnel experiments involved laminar and turbulent flow at various Re were performed. Hot-wire anemometry was used to investigate near-wall flow structure over smooth and riblet surfaces. The results showed that the convergent riblet plate significantly impacted the boundary layer properties. Furthermore, the turbulent skin friction drag over the convergent riblet was higher than on a smooth surface. The results agree well with previous studies.