Samuel Olusola Osisanya
Research Subjects
Research Interests
Samuel Olusola Osisanya has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
- Ramadan Ahmed
Mewbourne School of Petroleum and Geological Engineering, University of Oklahoma, Norman, OK 73019, USA
14 shared publications - Emmanuel Omojuwa
University of Oklahoma
6 shared publications - Omotayo Omosebi
AAPG, African University of Science and Technology, Abuja
6 shared publications Subhash Shah
The University of Oklahoma, United States
6 shared publicationsD. Tiab
The University of Oklahoma
5 shared publications- Arild Saasen
University of Stavanger
3 shared publications
Latest Publications
- 31 August 2020
- Published by American Society for Engineering Education
- p. 1.225.1-1.225.8
Freshman Engineering Teaching Experience Using Computers Problems And Solutions
- 31 August 2020
- Published by American Society for Engineering Education
- p. 1.225.1-1.225.8
Freshman Engineering Teaching Experience Using Computers Problems And Solutions
- 11 November 2019
- Published by Society of Petroleum Engineers (SPE)
Towards a Zero-Skin Well Completion with Non-Damaging Non-Corrosive Enzymatic Wellbore Cleanup Fluids
The objectives of this study were; (1) selection of size distribution of bridging particles of polymer-based drill-in fluid based on the actual reservoir porosity distribution in order to minimize the internal filtration damage, and (2) to develop a non-corrosive wellbore cleanup fluid comprising of a specially designed bio-enzyme and in-situ organic acid precursors to remove the external filter cakes and bring the skin close to zero prior to well completion. Drill-in-fluids were formulated and developed based on Ideal Packing Theory (IPT). The calcite particle size simulation was conducted using a particle size simulator based on IPT using FMI log information from a carbonate reservoir. Xanthan-starch specific bio-enzymes were screened and optimized to achieve complete dissolution of the polymers present in the mud-cakes. Acid precursors were formulated and developed to dissolve the calcite particles and at the same time keeping the corrosion level below the maximum acceptable limit. Compatibility tests between the acid precursors and the bio-enzymes were performed. The final cleanup formulation was subjected to corrosion studies at dynamic conditions. The entire development was verified at reservoir conditions through core flooding experiments. The formulated fluid was tested successfully against ceramic disks and carbonate core plugs by performing core-flood tests. The polymer based drill-in-fluid resulted in a very low permeability filter cake (<0.1 md), preventing internal filtrate damage significantly. Deposition of a very low permeability filter cake was achieved on carbonate core plugs which results in reduced damaging invasion. Several ester hydrolysis reaction kinetics were studied and finally one combination was chosen as the suitable acid precursor, because of their ability to generate required concentration of acid within three hours of hydrolysis at downhole condition. The best acid precursor satisfied the requirements by generating 3% of acid needed after 3 hours and maintained low acid concentrations for 12 hrs. The corrosion rates were found to be significantly below the industry limits and use of acid corrosion inhibitor is not necessary. Return-permeability of mud damaged carbonate core plugs was as high as 96% after exposing to clean-up solution. A new drill-in fluid has been developed and its filter-cake deposition was completely cleaned up with enzyme-acid precursor combination. Normally wellbore cleanup fluids are highly acidic and need corrosion inhibitor. The new formulation was effective in minimizing corrosion of downhole tools without the use of corrosion inhibitors.
- 11 November 2019
- Published by Society of Petroleum Engineers (SPE)
Towards a Zero-Skin Well Completion with Non-Damaging Non-Corrosive Enzymatic Wellbore Cleanup Fluids
The objectives of this study were; (1) selection of size distribution of bridging particles of polymer-based drill-in fluid based on the actual reservoir porosity distribution in order to minimize the internal filtration damage, and (2) to develop a non-corrosive wellbore cleanup fluid comprising of a specially designed bio-enzyme and in-situ organic acid precursors to remove the external filter cakes and bring the skin close to zero prior to well completion. Drill-in-fluids were formulated and developed based on Ideal Packing Theory (IPT). The calcite particle size simulation was conducted using a particle size simulator based on IPT using FMI log information from a carbonate reservoir. Xanthan-starch specific bio-enzymes were screened and optimized to achieve complete dissolution of the polymers present in the mud-cakes. Acid precursors were formulated and developed to dissolve the calcite particles and at the same time keeping the corrosion level below the maximum acceptable limit. Compatibility tests between the acid precursors and the bio-enzymes were performed. The final cleanup formulation was subjected to corrosion studies at dynamic conditions. The entire development was verified at reservoir conditions through core flooding experiments. The formulated fluid was tested successfully against ceramic disks and carbonate core plugs by performing core-flood tests. The polymer based drill-in-fluid resulted in a very low permeability filter cake (<0.1 md), preventing internal filtrate damage significantly. Deposition of a very low permeability filter cake was achieved on carbonate core plugs which results in reduced damaging invasion. Several ester hydrolysis reaction kinetics were studied and finally one combination was chosen as the suitable acid precursor, because of their ability to generate required concentration of acid within three hours of hydrolysis at downhole condition. The best acid precursor satisfied the requirements by generating 3% of acid needed after 3 hours and maintained low acid concentrations for 12 hrs. The corrosion rates were found to be significantly below the industry limits and use of acid corrosion inhibitor is not necessary. Return-permeability of mud damaged carbonate core plugs was as high as 96% after exposing to clean-up solution. A new drill-in fluid has been developed and its filter-cake deposition was completely cleaned up with enzyme-acid precursor combination. Normally wellbore cleanup fluids are highly acidic and need corrosion inhibitor. The new formulation was effective in minimizing corrosion of downhole tools without the use of corrosion inhibitors.
- 5 April 2017
- Published by Society of Petroleum Engineers (SPE)
Cement Degradation in CO2 - H2S Environment under High Pressure-High Temperature Conditions
Significant amount of oil and gas reserves contain CO2 and H2S. Leakage of these gases to fresh water aquifers and their escape to the surface compromises human health and safety and create unthinkable environmental hazards. Cement exposed to these acid gases degrade, thereby promoting their release through the wellbore to overlying fresh water formations and/or the environment. This study investigates how these contaminants aid the corrosion of well cement in high pressure-high temperature (HPHT) environment. Experiments were conducted under two broad test conditions. In the first case, cement cores were aged at 100°F in CO2-H2S brine solution. The total test pressure was varied from 3000 psi to 9000 psi. In the second case, cement cores were exposed to brine saturated with gas mixture comprising H2S, CO2, and CH4 at total test pressure of 6000 psi. Temperature was varied from 100°F to 350°F. The compressive strength, shear bond strength, porosity, and permeability of the aged and unaged specimens were measured to quantify the alteration in these critical cement properties. Observations are supported with FTIR, SEM and EDS analyses. As temperature increases, the presence of H2S shows more impact on the loss of mechanical strengths and increase in transport properties of Class G cement than Class H cement. Variation of H2S concentration also shows significant impact on cement integrity. Compared to previous study involving the exposure of cement to pure CO2, the presence of H2S improves the relative strength of cement. However, transport properties are compromised. FTIR mineralogy confirms that the extent to which cement is carbonated by CO2 is limited by the presence of H2S. In addition, SEM and EDX indicate that ettringite was formed at low temperature (100°F). However, it dissolves at high temperature (350°F) without significantly compromising the structural integrity of cement. The most significant new finding in this study is that the presence of H2S and its coexistence with CO2 under HPHT conditions minimizes the loss of the structural integrity of well cement by pure CO2. This is important because it narrows down the most significant factor to consider when designing acidresistant cements for HPHT wells.
- 5 April 2017
- Published by Society of Petroleum Engineers (SPE)
Cement Degradation in CO2 - H2S Environment under High Pressure-High Temperature Conditions
Significant amount of oil and gas reserves contain CO2 and H2S. Leakage of these gases to fresh water aquifers and their escape to the surface compromises human health and safety and create unthinkable environmental hazards. Cement exposed to these acid gases degrade, thereby promoting their release through the wellbore to overlying fresh water formations and/or the environment. This study investigates how these contaminants aid the corrosion of well cement in high pressure-high temperature (HPHT) environment. Experiments were conducted under two broad test conditions. In the first case, cement cores were aged at 100°F in CO2-H2S brine solution. The total test pressure was varied from 3000 psi to 9000 psi. In the second case, cement cores were exposed to brine saturated with gas mixture comprising H2S, CO2, and CH4 at total test pressure of 6000 psi. Temperature was varied from 100°F to 350°F. The compressive strength, shear bond strength, porosity, and permeability of the aged and unaged specimens were measured to quantify the alteration in these critical cement properties. Observations are supported with FTIR, SEM and EDS analyses. As temperature increases, the presence of H2S shows more impact on the loss of mechanical strengths and increase in transport properties of Class G cement than Class H cement. Variation of H2S concentration also shows significant impact on cement integrity. Compared to previous study involving the exposure of cement to pure CO2, the presence of H2S improves the relative strength of cement. However, transport properties are compromised. FTIR mineralogy confirms that the extent to which cement is carbonated by CO2 is limited by the presence of H2S. In addition, SEM and EDX indicate that ettringite was formed at low temperature (100°F). However, it dissolves at high temperature (350°F) without significantly compromising the structural integrity of cement. The most significant new finding in this study is that the presence of H2S and its coexistence with CO2 under HPHT conditions minimizes the loss of the structural integrity of well cement by pure CO2. This is important because it narrows down the most significant factor to consider when designing acidresistant cements for HPHT wells.
- 7 November 2016
- Published by Society of Petroleum Engineers (SPE)
Development of New Smart Drilling Fluids Using Nano-Materials for Unconventional Reservoirs
Drilling fluids used for accessing unconventional reservoirs need new focus because the fluids used to exploit conventional reservoirs need without some modifications or new formulations. New smart-fluid formulations were developed and optimized using nano-materials. Three nano-materials were added to the generic water-based fluids. Scanning electronic microscope tests were performed to check the size quality of the nano-materials. Rheology properties, pH and filtration tests were performed to evaluate the smart drilling fluids. Mud cakes formed by each smart drilling fluid were collected and scanned. For practical field applications, the smart drilling fluids were tested against two rock samples by performing dispersion, barite sag and aging (stability) tests. The rocks were characterized using scanning electronic microscope (SEM), cation exchange capacity (CEC) and adsorption tests. Results showed that the developed fluids exhibited excellent rheological properties and the filtration losses were reduced after adding nano-materials. Mud cakes formed by each smart drilling fluid were collected and scanned. Thin, tight, and well textured mud cakes were formed. The mud cakes' thicknesses were reduced significantly after adding nano materials. The barite sag tests indicated the fluids to be excellent for cutting suspension. No sedimentation was observed after aging for three days, which indicated a good cleaning and suspension of drilled cuttings. The rheology and filtration properties of smart drilling fluid system remained stable under static condition after three days of aging. Results showed reduced shale dispersion, excellent suspension capacity, and stability. The cost comparison between the developed smart drilling fluids with nano-materials and base (generic) drilling fluids shows that that the smart fluids are relatively inexpensive even though they are excellent for preventing wellbore instability and for used in the environmentally sensitive areas.
- 7 November 2016
- Published by Society of Petroleum Engineers (SPE)
Development of New Smart Drilling Fluids Using Nano-Materials for Unconventional Reservoirs
Drilling fluids used for accessing unconventional reservoirs need new focus because the fluids used to exploit conventional reservoirs need without some modifications or new formulations. New smart-fluid formulations were developed and optimized using nano-materials. Three nano-materials were added to the generic water-based fluids. Scanning electronic microscope tests were performed to check the size quality of the nano-materials. Rheology properties, pH and filtration tests were performed to evaluate the smart drilling fluids. Mud cakes formed by each smart drilling fluid were collected and scanned. For practical field applications, the smart drilling fluids were tested against two rock samples by performing dispersion, barite sag and aging (stability) tests. The rocks were characterized using scanning electronic microscope (SEM), cation exchange capacity (CEC) and adsorption tests. Results showed that the developed fluids exhibited excellent rheological properties and the filtration losses were reduced after adding nano-materials. Mud cakes formed by each smart drilling fluid were collected and scanned. Thin, tight, and well textured mud cakes were formed. The mud cakes' thicknesses were reduced significantly after adding nano materials. The barite sag tests indicated the fluids to be excellent for cutting suspension. No sedimentation was observed after aging for three days, which indicated a good cleaning and suspension of drilled cuttings. The rheology and filtration properties of smart drilling fluid system remained stable under static condition after three days of aging. Results showed reduced shale dispersion, excellent suspension capacity, and stability. The cost comparison between the developed smart drilling fluids with nano-materials and base (generic) drilling fluids shows that that the smart fluids are relatively inexpensive even though they are excellent for preventing wellbore instability and for used in the environmentally sensitive areas.
- 1 November 2016
- Published by Elsevier in Cement and Concrete Composites
- Vol. 74, 54-70
Degradation of well cement in HPHT acidic environment: Effects of CO2 concentration and pressure
- 1 November 2016
- Published by Elsevier in Cement and Concrete Composites
- Vol. 74, 54-70
Degradation of well cement in HPHT acidic environment: Effects of CO2 concentration and pressure
- 1 October 2016
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 146, 777-787
Corrosion of C110 carbon steel in high-pressure aqueous environment with mixed hydrocarbon and CO2 gas
- 1 October 2016
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 146, 777-787
Corrosion of C110 carbon steel in high-pressure aqueous environment with mixed hydrocarbon and CO2 gas
- 19 April 2016
- Published by Taylor & Francis
Project Management for the Oil and Gas Industry
Project management for oil and gas projects comes with a unique set of challenges that include the management of science, technology, and engineering aspects. Underlining the specific issues involved in projects in this field, Project Management for the Oil and Gas Industry: A World System Approach presents step-by-step application of project manag
- 19 April 2016
- Published by Taylor & Francis
Project Management for the Oil and Gas Industry
Project management for oil and gas projects comes with a unique set of challenges that include the management of science, technology, and engineering aspects. Underlining the specific issues involved in projects in this field, Project Management for the Oil and Gas Industry: A World System Approach presents step-by-step application of project manag
- 17 November 2015
- Published by Society of Petroleum Engineers (SPE)
Mechanical Integrity of Well Cement Under Geologic Carbon Sequestration Conditions
Carbon dioxide (CO2) is injected into subsurface rocks either to improve hydrocarbon recovery or for permanent storage in geologic formations. At storage sites, CO2 injection wells are drilled and completed with multiple-string casings, which are cemented to the host rock. Cement is the primary means of protecting these casings from corrosive fluids and isolating storage zones from overlying fresh water aquifers by effectively sealing the casing-rock annulus. Over the life of the well, dissolved CO2 interacts with the casing-cement-rock system thereby degrading the hardened cement and resulting in loss of zonal isolation and structural integrity required to support the casing and to ensure long-term integrity of the well. Cement performance is often assessed through laboratory measurement of compressive strength, porosity and permeability. These parameters are indicators of mechanical integrity. Although compressive strength in the range of 0.7 to 5 MPa is generally sufficient to continue drilling after the casing is cemented, further hydration and chemical degradation occur throughout the operational life of the well. In CO2 injection wells, environmental conditions (i.e. CO2 concentration, pressure and temperature) around the cement result in further alteration in mechanical properties. This hostile environment causes severe mechanical damage and ultimate failure of cement sheath, potentially leading to micro-channelling and formation of micro-annuli. In this study, experiments were conducted to investigate the effect of CO2 concentration on mechanical integrity of well cements (Classes G and H) after exposure to carbonic acid environment. Cement cores were prepared and aged for 14 days in autoclave filled with 2% NaCl solution saturated with methane gas containing carbon dioxide. Aging tests were performed at 38°C and 42 MPa, varying CO2 concentration. To assess the level of degradation and describe the process of acid attack, compressive strengths of unexposed and exposed specimens were measured and compared. In addition, other properties of cement cores including porosity, permeability, stiffness/elasticity and Fourier Transform Infrared Spectroscopy (FTIR) measurements were obtained and used in the assessment. After 14 days of exposure, increase in CO2 concentration leads to insignificant changes in compressive strength due to combined effect of carbonation of cement hydrates (calcium silicate hydrates and calcium hydroxide) and subsequent leaching, with each process compensating for the other. Porosity, permeability and FTIR measurements are consistent with this observation. Under the experimental conditions adopted in this study, durability of Classes G and H cement are comparable. However, Class H cement becomes more elastic (i.e. less stiff) than Class G cement as CO2 concentration increases. FTIR mineralogy provides evidence that the mechanical behaviour of well cement after exposure to CO2-saturated brine is a direct consequence of interconnected chemical processes. Under carbon sequestration conditions, these processes counterbalance one another to ensure long-term integrity of the well for CO2 storage and containment.
- 17 November 2015
- Published by Society of Petroleum Engineers (SPE)
Mechanical Integrity of Well Cement Under Geologic Carbon Sequestration Conditions
Carbon dioxide (CO2) is injected into subsurface rocks either to improve hydrocarbon recovery or for permanent storage in geologic formations. At storage sites, CO2 injection wells are drilled and completed with multiple-string casings, which are cemented to the host rock. Cement is the primary means of protecting these casings from corrosive fluids and isolating storage zones from overlying fresh water aquifers by effectively sealing the casing-rock annulus. Over the life of the well, dissolved CO2 interacts with the casing-cement-rock system thereby degrading the hardened cement and resulting in loss of zonal isolation and structural integrity required to support the casing and to ensure long-term integrity of the well. Cement performance is often assessed through laboratory measurement of compressive strength, porosity and permeability. These parameters are indicators of mechanical integrity. Although compressive strength in the range of 0.7 to 5 MPa is generally sufficient to continue drilling after the casing is cemented, further hydration and chemical degradation occur throughout the operational life of the well. In CO2 injection wells, environmental conditions (i.e. CO2 concentration, pressure and temperature) around the cement result in further alteration in mechanical properties. This hostile environment causes severe mechanical damage and ultimate failure of cement sheath, potentially leading to micro-channelling and formation of micro-annuli. In this study, experiments were conducted to investigate the effect of CO2 concentration on mechanical integrity of well cements (Classes G and H) after exposure to carbonic acid environment. Cement cores were prepared and aged for 14 days in autoclave filled with 2% NaCl solution saturated with methane gas containing carbon dioxide. Aging tests were performed at 38°C and 42 MPa, varying CO2 concentration. To assess the level of degradation and describe the process of acid attack, compressive strengths of unexposed and exposed specimens were measured and compared. In addition, other properties of cement cores including porosity, permeability, stiffness/elasticity and Fourier Transform Infrared Spectroscopy (FTIR) measurements were obtained and used in the assessment. After 14 days of exposure, increase in CO2 concentration leads to insignificant changes in compressive strength due to combined effect of carbonation of cement hydrates (calcium silicate hydrates and calcium hydroxide) and subsequent leaching, with each process compensating for the other. Porosity, permeability and FTIR measurements are consistent with this observation. Under the experimental conditions adopted in this study, durability of Classes G and H cement are comparable. However, Class H cement becomes more elastic (i.e. less stiff) than Class G cement as CO2 concentration increases. FTIR mineralogy provides evidence that the mechanical behaviour of well cement after exposure to CO2-saturated brine is a direct consequence of interconnected chemical processes. Under carbon sequestration conditions, these processes counterbalance one another to ensure long-term integrity of the well for CO2 storage and containment.
- 9 November 2015
- Published by Society of Petroleum Engineers (SPE)
An Economic Approach to Horizontal Well Length Optimization
Horizontal wells offer higher productivity when compared to vertical wells due to increased contact area with the reservoir. It is now accepted that an increase in well length is not proportional to higher productivity after a certain critical well length because of frictional pressure losses in the wellbore. As the well length increases, so does the frictional pressure loss. In most cases there is an optimal well length beyond which a productivity decline will occur. The purpose of this study is to present findings on horizontal well optimization taking into consideration frictional pressure loss effects with and without perforations in the wellbore. Several horizontal well productivity equations can be found in the literature. In this study a productivity equation based on an elliptical drainage area is assumed. Other assumptions include single-phase incompressible oil, isothermal condition, and homogeneous reservoir with directional change in permeability. Parametric studies were conducted to investigate the effects of pressure drawdown, wellbore diameter, horizontal permeability, formation anisotropy, and oil viscosity on well performance. A probabilistic economic approach based on net present value (NPV) is used to determine the optimal well length for a particular set of reservoir and well parameters that will be useful for planning and designing horizontal wells. Results show the following: Horizontal well productivity is significantly affected by oil viscosity, horizontal permeability, and well diameter. Those parameters must be considered for the optimization of horizontal well length.Frictional pressure losses have a significant effect on the productivity of small diameter wellbores in high permeability formations containing relatively low viscous oil.Sensitivity analysis of economic parameters indicates that oil price had the greatest effect on NPV at a particular well length. Production taxes and operating costs ranked second and third, respectively, with negative effects on NPV.
- 9 November 2015
- Published by Society of Petroleum Engineers (SPE)
An Economic Approach to Horizontal Well Length Optimization
Horizontal wells offer higher productivity when compared to vertical wells due to increased contact area with the reservoir. It is now accepted that an increase in well length is not proportional to higher productivity after a certain critical well length because of frictional pressure losses in the wellbore. As the well length increases, so does the frictional pressure loss. In most cases there is an optimal well length beyond which a productivity decline will occur. The purpose of this study is to present findings on horizontal well optimization taking into consideration frictional pressure loss effects with and without perforations in the wellbore. Several horizontal well productivity equations can be found in the literature. In this study a productivity equation based on an elliptical drainage area is assumed. Other assumptions include single-phase incompressible oil, isothermal condition, and homogeneous reservoir with directional change in permeability. Parametric studies were conducted to investigate the effects of pressure drawdown, wellbore diameter, horizontal permeability, formation anisotropy, and oil viscosity on well performance. A probabilistic economic approach based on net present value (NPV) is used to determine the optimal well length for a particular set of reservoir and well parameters that will be useful for planning and designing horizontal wells. Results show the following: Horizontal well productivity is significantly affected by oil viscosity, horizontal permeability, and well diameter. Those parameters must be considered for the optimization of horizontal well length.Frictional pressure losses have a significant effect on the productivity of small diameter wellbores in high permeability formations containing relatively low viscous oil.Sensitivity analysis of economic parameters indicates that oil price had the greatest effect on NPV at a particular well length. Production taxes and operating costs ranked second and third, respectively, with negative effects on NPV.