Hochang Jang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hochang Jang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jeonghwan Lee
Chonnam National University
10 shared publications Jeonghwan Lee
7 shared publicationsYoungmin Kim
4 shared publicationsChangjae Kim
Department of Energy & Resources Engineering, Chonnam National University, Buk-Gu, Gwangju, Korea
3 shared publicationsJunggyun Kim
2 shared publications- Seungmo Ko
Department of Energy and Mineral Resources Engineering, Kangwon National University, Samcheok 25913, Republic of Korea
2 shared publications
Latest Publications
- Open Access
Simulation Study on Injection/Withdrawal Scenarios of Hydrogen-Blended Methane in a Depleted Gas Reservoir
This study presents a quantitative simulation analysis of hydrogen-enriched methane (HENG) storage with nitrogen as the cushion-gas in a depleted gas reservoir by varying three key operational parameters: the injection/withdrawal period, hydrogen blending ratio (5–20%), and injection depth. Ten injection–withdrawal cycles were modeled for each scenario, and performance was evaluated using cycle-averaged and cumulative hydrogen purity, recovery factors, and the mixing zone size. Extending the injection period increased hydrogen purity to 20.00–20.26% and reduced nitrogen to 0.001–0.003%, but recovery decreased from 65.63 to 53.83–41.09% due to enhanced dispersion and residual trapping. The blending ratio was the dominant control: 20% blending yielded 19.9–20.0% purity with nitrogen as low as 0.00–0.03%, whereas 5–10% blending produced lower purity but minimized nitrogen production to 0.97–1.08%. Injection depth affected nitrogen recovery more than purity, increasing from 0.72–1.20% (upper) to 1.46–1.61% (lower), along with thicker mixing zones. Final mixing zone size ranged from 3176 to 5546 blocks, with smaller zones consistently linked to higher purity and lower nitrogen breakthrough. The shut-in period further reduced nitrogen recovery from 6.49 to 1.33% and stabilized mixing behavior. Overall, minimizing late-cycle mixing zone thickness is essential for maintaining HENG storage performance. Although this study provides quantitative insights into HENG operational strategies, the use of a homogeneous grid and simplified fluid properties limits representation of geological heterogeneity and reactive processes. Future work will incorporate heterogeneity and reaction modeling into field-scale simulations to validate and refine these operating strategies for practical deployment.
Open AccessSimulation Study on Injection/Withdrawal Scenarios of Hydrogen-Blended Methane in a Depleted Gas Reservoir
This study presents a quantitative simulation analysis of hydrogen-enriched methane (HENG) storage with nitrogen as the cushion-gas in a depleted gas reservoir by varying three key operational parameters: the injection/withdrawal period, hydrogen blending ratio (5–20%), and injection depth. Ten injection–withdrawal cycles were modeled for each scenario, and performance was evaluated using cycle-averaged and cumulative hydrogen purity, recovery factors, and the mixing zone size. Extending the injection period increased hydrogen purity to 20.00–20.26% and reduced nitrogen to 0.001–0.003%, but recovery decreased from 65.63 to 53.83–41.09% due to enhanced dispersion and residual trapping. The blending ratio was the dominant control: 20% blending yielded 19.9–20.0% purity with nitrogen as low as 0.00–0.03%, whereas 5–10% blending produced lower purity but minimized nitrogen production to 0.97–1.08%. Injection depth affected nitrogen recovery more than purity, increasing from 0.72–1.20% (upper) to 1.46–1.61% (lower), along with thicker mixing zones. Final mixing zone size ranged from 3176 to 5546 blocks, with smaller zones consistently linked to higher purity and lower nitrogen breakthrough. The shut-in period further reduced nitrogen recovery from 6.49 to 1.33% and stabilized mixing behavior. Overall, minimizing late-cycle mixing zone thickness is essential for maintaining HENG storage performance. Although this study provides quantitative insights into HENG operational strategies, the use of a homogeneous grid and simplified fluid properties limits representation of geological heterogeneity and reactive processes. Future work will incorporate heterogeneity and reaction modeling into field-scale simulations to validate and refine these operating strategies for practical deployment.
- Open Access
- 15 October 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Compositional simulation of the synergistic impact of impurities and geochemical reactions on the efficiency of impure CO₂ sequestration at a Korean CCS site
- 15 October 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Open AccessCompositional simulation of the synergistic impact of impurities and geochemical reactions on the efficiency of impure CO₂ sequestration at a Korean CCS site
- Open Access
Nano-Water-Alternating-Gas Simulation Study Considering Rock–Fluid Interaction in Heterogeneous Carbonate Reservoirs
In carbonate reservoirs, nanoparticles can adhere to rock surfaces, potentially altering the rock wettability and modifying the absolute permeability. In the water-alternating-gas (WAG) process, the introduction of nanoparticles into the water phase, termed nano-water-alternating gas (NWAG), is a promising approach for enhancing oil recovery and CO2 storage. The NWAG process can alter rock wettability and absolute permeability through the adsorption of nanoparticles on the rock surface. This study investigated the efficiency of the NWAG method, which utilizes nanofluids in CO2-enhanced oil recovery (EOR) processes to simultaneously recover oil and store CO2 using 1D core and 3D heterogeneous reservoir models. The simulation results of the 1D core model showed that applying the NWAG method enhanced both oil recovery and CO2 storage efficiency by increasing to 3%. In a 3D reservoir model, a Dykstra–Parsons coefficient of 0.4 was selected to represent reservoir heterogeneity. Additionally, the capillary trapping of CO2 during WAG injection was computed using Larsen and Skauge’s three-phase relative permeability hysteresis model. A sensitivity analysis was performed using the NWAG ratio, slug size, injection period, injection cycle, and nanofluid concentration. The results confirmed an increase of 0.8% in oil recovery and 15.2% in CO2 storage compared with the conventional WAG process. This mechanism suggests that nanofluids can enhance oil recovery and expand CO2 storage, improving the efficiency of both the oil production rate and CO2 storage compared to conventional WAG methods.
Open AccessNano-Water-Alternating-Gas Simulation Study Considering Rock–Fluid Interaction in Heterogeneous Carbonate Reservoirs
In carbonate reservoirs, nanoparticles can adhere to rock surfaces, potentially altering the rock wettability and modifying the absolute permeability. In the water-alternating-gas (WAG) process, the introduction of nanoparticles into the water phase, termed nano-water-alternating gas (NWAG), is a promising approach for enhancing oil recovery and CO2 storage. The NWAG process can alter rock wettability and absolute permeability through the adsorption of nanoparticles on the rock surface. This study investigated the efficiency of the NWAG method, which utilizes nanofluids in CO2-enhanced oil recovery (EOR) processes to simultaneously recover oil and store CO2 using 1D core and 3D heterogeneous reservoir models. The simulation results of the 1D core model showed that applying the NWAG method enhanced both oil recovery and CO2 storage efficiency by increasing to 3%. In a 3D reservoir model, a Dykstra–Parsons coefficient of 0.4 was selected to represent reservoir heterogeneity. Additionally, the capillary trapping of CO2 during WAG injection was computed using Larsen and Skauge’s three-phase relative permeability hysteresis model. A sensitivity analysis was performed using the NWAG ratio, slug size, injection period, injection cycle, and nanofluid concentration. The results confirmed an increase of 0.8% in oil recovery and 15.2% in CO2 storage compared with the conventional WAG process. This mechanism suggests that nanofluids can enhance oil recovery and expand CO2 storage, improving the efficiency of both the oil production rate and CO2 storage compared to conventional WAG methods.
- Open Access
- 9 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (19) , 11105
Enhancing Oil Recovery and Altering Wettability in Carbonate Reservoir Rocks through (3-Glycidoxypropyl)trimethoxysilane–SiO2 Nanofluid Injection
This study analyzes the impact of injection condition design factors of (3-glycidoxypropyl)trimethoxysilane (GPTMS)–SiO2 nanofluid on improving wettability and oil recovery through flotation and core flooding tests, respectively. Flotation tests were conducted to assess improvements in wettability that resulted from varying nanoparticle concentration, reaction time, and treatment temperature. The test results demonstrated that the hydrophilic sample ratio increased by up to 97.75% based on the nanoparticle reaction, confirming significant wettability improvement in all samples. Additionally, time-dependent fluid-flow experiments were conducted to validate oil recovery and rock–fluid interactions. In these experiments, for a 24-h reaction time, nanofluid injection caused a decrease in the maximum contact angle (43.4° from 166.5°) and a remarkable enhancement in the oil recovery rate by over 25%. Moreover, variations in contact angle and sample permeability were observed as the reaction time increased. Subsequently, the core flooding test revealed a critical reaction time of 24 h, maximizing oil recovery while minimizing permeability. Below this point in time, wettability improvement did not significantly enhance oil recovery. Conversely, beyond this threshold, additional adsorption due to particle aggregation decreased permeability, causing reduced oil recovery. Therefore, GPTMS–SiO2 nanofluid can be utilized as an injection fluid to enhance oil recovery in high-temperature and high-salinity carbonate reservoirs.
- 9 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (19) , 11105
Open AccessEnhancing Oil Recovery and Altering Wettability in Carbonate Reservoir Rocks through (3-Glycidoxypropyl)trimethoxysilane–SiO2 Nanofluid Injection
This study analyzes the impact of injection condition design factors of (3-glycidoxypropyl)trimethoxysilane (GPTMS)–SiO2 nanofluid on improving wettability and oil recovery through flotation and core flooding tests, respectively. Flotation tests were conducted to assess improvements in wettability that resulted from varying nanoparticle concentration, reaction time, and treatment temperature. The test results demonstrated that the hydrophilic sample ratio increased by up to 97.75% based on the nanoparticle reaction, confirming significant wettability improvement in all samples. Additionally, time-dependent fluid-flow experiments were conducted to validate oil recovery and rock–fluid interactions. In these experiments, for a 24-h reaction time, nanofluid injection caused a decrease in the maximum contact angle (43.4° from 166.5°) and a remarkable enhancement in the oil recovery rate by over 25%. Moreover, variations in contact angle and sample permeability were observed as the reaction time increased. Subsequently, the core flooding test revealed a critical reaction time of 24 h, maximizing oil recovery while minimizing permeability. Below this point in time, wettability improvement did not significantly enhance oil recovery. Conversely, beyond this threshold, additional adsorption due to particle aggregation decreased permeability, causing reduced oil recovery. Therefore, GPTMS–SiO2 nanofluid can be utilized as an injection fluid to enhance oil recovery in high-temperature and high-salinity carbonate reservoirs.
- Open Access
- 12 September 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (18) , 13620
A Simulation Study on Evaluating the Influence of Impurities on Hydrogen Production in Geological Carbon Dioxide Storage
In this study, we examined the effect of CO2 injection into deep saline aquifers, considering impurities present in blue hydrogen production. A fluid model was designed for reservoir conditions with impurity concentrations of 3.5 and 20%. The results showed that methane caused density decreases of 95.16 and 76.16% at 3.5 and 20%, respectively, whereas H2S caused decreases of 99.56 and 98.77%, respectively. Viscosity decreased from 0.045 to 0.037 cp with increasing methane content up to 20%; however, H2S did not affect the viscosity. Notably, CO2 with H2S impacted these properties less than methane. Our simulation model was based on the Gorae-V properties and simulated injections for 10 years, followed by 100 years of monitoring. Compared with the pure CO2 injection, methane reached its maximum pressure after eight years and eleven months at 3.5% and eight years at 20%, whereas H2S reached maximum pressure after nine years and two months and nine years and six months, respectively. These timings affected the amount of CO2 injected. With methane as an impurity, injection efficiency decreased up to 73.16%, whereas with H2S, it decreased up to 81.99% with increasing impurity concentration. The efficiency of CO2 storage in the dissolution and residual traps was analyzed to examine the impact of impurities. The residual trap efficiency consistently decreased with methane but increased with H2S. At 20% concentration, the methane trap exhibited higher efficiency at the end of injection; however, H2S had a higher efficiency at the monitoring endpoint. In carbon capture and storage projects, methane impurities require removal, whereas H2S may not necessitate desulfurization due to its minimal impact on CO2 storage efficiency. Thus, the application of carbon capture and storage (CCS) to CO2 emissions containing H2S as an impurity may enable economically viable operations by reducing additional costs.
- 12 September 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (18) , 13620
Open AccessA Simulation Study on Evaluating the Influence of Impurities on Hydrogen Production in Geological Carbon Dioxide Storage
In this study, we examined the effect of CO2 injection into deep saline aquifers, considering impurities present in blue hydrogen production. A fluid model was designed for reservoir conditions with impurity concentrations of 3.5 and 20%. The results showed that methane caused density decreases of 95.16 and 76.16% at 3.5 and 20%, respectively, whereas H2S caused decreases of 99.56 and 98.77%, respectively. Viscosity decreased from 0.045 to 0.037 cp with increasing methane content up to 20%; however, H2S did not affect the viscosity. Notably, CO2 with H2S impacted these properties less than methane. Our simulation model was based on the Gorae-V properties and simulated injections for 10 years, followed by 100 years of monitoring. Compared with the pure CO2 injection, methane reached its maximum pressure after eight years and eleven months at 3.5% and eight years at 20%, whereas H2S reached maximum pressure after nine years and two months and nine years and six months, respectively. These timings affected the amount of CO2 injected. With methane as an impurity, injection efficiency decreased up to 73.16%, whereas with H2S, it decreased up to 81.99% with increasing impurity concentration. The efficiency of CO2 storage in the dissolution and residual traps was analyzed to examine the impact of impurities. The residual trap efficiency consistently decreased with methane but increased with H2S. At 20% concentration, the methane trap exhibited higher efficiency at the end of injection; however, H2S had a higher efficiency at the monitoring endpoint. In carbon capture and storage projects, methane impurities require removal, whereas H2S may not necessitate desulfurization due to its minimal impact on CO2 storage efficiency. Thus, the application of carbon capture and storage (CCS) to CO2 emissions containing H2S as an impurity may enable economically viable operations by reducing additional costs.
- 1 February 2020
- Published by Elsevier in Journal of Industrial and Engineering Chemistry
- Vol. 82, 349-358
Prevention of hydrate plugging by kinetic inhibitor in subsea flowline considering the system availability of offshore gas platform
- 1 February 2020
- Published by Elsevier in Journal of Industrial and Engineering Chemistry
- Vol. 82, 349-358
Prevention of hydrate plugging by kinetic inhibitor in subsea flowline considering the system availability of offshore gas platform
- 1 August 2019
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 106, 38-45
Rheological characteristics of non-Newtonian GPTMS-SiO2 nanofluids
- 1 August 2019
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 106, 38-45
Rheological characteristics of non-Newtonian GPTMS-SiO2 nanofluids
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Oil, Gas and Coal Technology
- Vol. 20 (2) , 143
Prediction of production performance by comprehensive methodology for hydraulically fractured well in coalbed methane reservoirs
Production data from hydraulically fractured well in coalbed methane (CBM) reservoirs was analysed using decline curve analysis (DCA), flow regime analysis, and flowing material balance to forecast the production performance and to determine estimated ultimate recovery (EUR) and timing for applying the DCA. To generate synthetic production data, reservoir models were built based on the CBM properties of the San Juan Basin and Appalachian Basin. Production data analysis shows that the transient flow (TF) occurs for 1~3 years in the vertical well and 6~16 years in the horizontal well and then the boundary dominated flow (BDF) was reached. In the TF period, it is impossible to forecast the production performance. In case of vertical well, if the production data are available for more than three years after the BDF has been reached, the production rate and EUR can be predicted with EUR error of approximately 5%. In the case of a horizontal well, the prediction can be conducted using the production data of more than a year after reached BDF with EUR error of approximately 5%. [Received: January 30, 2016; Accepted: February 3, 2017]
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Oil, Gas and Coal Technology
- Vol. 20 (2) , 143
Prediction of production performance by comprehensive methodology for hydraulically fractured well in coalbed methane reservoirs
Production data from hydraulically fractured well in coalbed methane (CBM) reservoirs was analysed using decline curve analysis (DCA), flow regime analysis, and flowing material balance to forecast the production performance and to determine estimated ultimate recovery (EUR) and timing for applying the DCA. To generate synthetic production data, reservoir models were built based on the CBM properties of the San Juan Basin and Appalachian Basin. Production data analysis shows that the transient flow (TF) occurs for 1~3 years in the vertical well and 6~16 years in the horizontal well and then the boundary dominated flow (BDF) was reached. In the TF period, it is impossible to forecast the production performance. In case of vertical well, if the production data are available for more than three years after the BDF has been reached, the production rate and EUR can be predicted with EUR error of approximately 5%. In the case of a horizontal well, the prediction can be conducted using the production data of more than a year after reached BDF with EUR error of approximately 5%. [Received: January 30, 2016; Accepted: February 3, 2017]