HCHana Chmelickova

Hana Chmelickova

*This is an algorithmically generated author record based on publicly available information.

Hana Chmelickova has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Optical triggering of a metal-insulator transition in neodymium nickelate films

    by Alexandr Stupakov, Tomáš Kocourek, Volha Vetokhina, Joris More-Chevalier, Hana Chmelíčková, Alexandr Dejneka, Marina Tyunina


  • Properties of focusing polycapillary utilized in 57Fe Mössbauer spectroscopy

    by Jan Kočiščák, Petr Novák, Hana Chmelíčková, Vít Procházka


  • Open Access

    BENEFITS OF USE OF ACOUSTIC EMISSION IN SCRATCH TESTING

    by Lukáš Václavek, Jan Tomáštík, Hana Chmelíčková, Radim Čtvrtlík

    Scratch test is regularly used for assessment of cohesive and adhesive strength of thin films and coatings. By default, its evaluation is based on analysis of depth-load-time record and microscopic observation of residual scratch groove. The visual analysis of the residual groove provides the most detailed description of the final damage of the surface (crack patterns, extent of plastic deformation, delamination, etc.), but it may be a time demanding approach. Although the continuous recording of indenter penetration depth and applied load offers instantaneous information about the performance of the tested material, it may not provide sufficient description of the sample’s deformation behaviour. Therefore, other complementary techniques for description of the deformation response to scratch loading are desirable. Continuous recording of acoustic emissions (AE) generated during the test could be a possible solution. It is especially the ability of AE method to detect the very first and even subsurface failures of the material that is of the most importance and otherwise inaccessible by standardly used techniques. What is more, it is a non-destructive and real-time method. In principle, AE method can be beneficially employed for a wide range of materials explored via scratch test. The strength of the AE analysis of the nano/micro scratch test will be demonstrated on various types of materials including optical thin films, durable metal and hard ceramic films as well as bulk laser cladding. Selected phenomena and features of the use of AE during scratch testing will be presented, including effect of scratch load on character of AE records (burst vs. continuous) for TiO2 on glass, subsurface damage of SiC films on silicon and selective failure of hard carbide phase embedded in a metal matrix in case of laser re-melted layers.


  • Laser treatment of alumina-based ceramics using second harmonics of Q-switched Nd:YLF laser

    by Lenka Rihakova, Hana Chmelickova, Helena Hiklova

    This paper is dedicated to laser engraving and drilling process of the alumina ceramics. Both processes are characterized by exquisite features in comparison with conventional ones. The main benefits are high speed, high precision and good quality along with flexibility. Moreover ceramics are hardly processed by conventional methods due to their high hardness and brittleness. Analysis of Nd:YLF laser engraving alumina ceramics concerning the influence of parameters like output power, processing speed and number of runs on various mark characteristics was carried out. Mark width, mark depth and contrast were evaluated and it was found out that output power determines both mark depth and width. Higher power caused generation of deeper and wider marks characterized by high contrast. Processing speed controls the overlapping of spots and the laser-material interaction time, thus having impact on the mark depth and contrast. Laser drilling was examined in dependence of output power that had crucial effect on the hole depth not on diameter. The research clarified that high output powers are necessary for producing deep holes so as high output powers together with low processing speeds are the optimal parameters to get maximal mark width and depth with satisfactory quality during engraving. Samples were analyzed using confocal microscope and contact profilometer. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

  • Lateral resolution of desorption nanoelectrospray: a nanospray tip without nebulizing gas as a source of primary charged droplets

    by L. Hartmanová, I. Lorencová, M. Volný, P. Fryčák, V. Havlíček, H. Chmelíčková, T. Ingr, K. Lemr

    Desorption nanoelectrospray (nanoDESI) was described in 2007 and it represents a miniaturized version of desorption electrospray without the assistance of the nebulizing gas. Compared to DESI, a nanoelectrospray tip (2 ± 1 μm I.D.) generates primary charged droplets of smaller sizes and lower spray liquid flow rates. This is the first report on utilization of nanoDESI for mass spectrometry imaging (MSI). Its new coupling with a Q-TOF instrument allowed faster mass spectra acquisition (4 Hz) essential for MSI of fine surface details. To evaluate nanoDESI potential for mass spectrometry imaging, etched glass substrates with Rhodamine B patterns of different dimensions were prepared. The Rhodamine B lines were analysed in 1D scanning mode and their width was determined experimentally by nanoDESI measurement. The experimental data revealed that the lateral resolution of nanoDESI is close to 30 μm along the x-axis (orthogonal to the inlet). 2D scanning mode confirmed good resolution along both axes as dye squares with dimensions about 60 μm × 60 μm were easily distinguished. The low flow rate of the spray liquid reduced undesirable analyte washing effects, which allowed repeated scanning analysis of the surface. The presented results demonstrate the applicability of nanoDESI for high surface resolution mass spectrometry imaging.


  • Open Access

    Laser Micromachining of Glass, Silicon, and Ceramics

    by L. Rihakova, H. Chmelickova

    A brief review is focused on laser micromachining of materials. Micromachining of materials is highly widespread method used in many industries, including semiconductors, electronic, medical, and automotive industries, communication, and aerospace. This method is a promising tool for material processing with micron and submicron resolution. In this paper micromachining of glass, silicon, and ceramics is considered. Interaction of these materials with laser radiation and recent research held on laser material treatment is provided.


  • Open Access

    High power diode laser remelting of metals

    by H Chmelickova, J Tomastik, R Ctvrtlik, J Supik, S Nemecek, M Misek

  • Energy Losses Estimation During Pulsed-Laser Seam Welding

    by Hana Sebestova, Martina Havelkova, Hana Chmelickova


  • Laser welding control by monitoring of plasma

    by Hana Chmelickova, Hana Sebestova, Martina Havelkova, Lenka Rihakova, Libor Nozka

    Deep penetration welding is a typical industrial application of high power lasers, where plasma can be generated above the keyhole. Thanks to the plasma plume presence welding process can be controlled on-line by means of the plasma intensity measurements. Various on-line monitoring methods have been developed in research centers all over the world. Goal of them is to enable promptly operator action to avoid enormous economical looses if un-expected defect is detected. Our laboratory was participated in project CLET - “Closed loop control of the laser welding process through the measurement of plasma” as a responsible partner for developed system testing both in the laboratory with pulsed Nd:YAG laser and in the real welding facility with high power continual CO2 laser. Control system is based on the electron temperature computation from the relative intensities of couple of emission lines belong to certain metal ion present in plasma plume. Our experiment was realized using Ocean Optics HR2000+ spectrometer within the stainless steel tube longitudinal welding. Several couples of emission lines were tested to acquire a good signal at actual welding conditions. Then power calibration was made to obtain the electron temperature dependence on increasing power. Samples were prepared for microanalysis and measured by laser confocal scanning microscope to find optimal power range for full penetrations achieving without thermal distortion of the tube or weld humping. Numerical model of the remelted area cross section was made to display temperature distribution dependence on increasing power.