Hüseyin Turhan
Research Subjects
Research Interests
Hüseyin Turhan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
M Aksoy
2 shared publicationsO. Yilmaz
2 shared publicationsSerkan Özel
Bitlis
2 shared publicationsV Kuzucu
2 shared publicationsM.M Yıldırım
1 shared publication- Mehmet Yaz
Firat Universitesi
1 shared publication
Latest Publications
- 1 April 2010
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 52 (4) , 252-256
Plasma Spray Coating of an AA 2024-T4 Al Alloy with Oxide Powders
In this study, the surface of AA2024-T4 Al alloy substrate was coated by Al2O3 + TiO2 powders without and with NiAl bond coat by using a plasma spray process. The TiO2 content was added at different concentrations (3, 13 and 40 wt.-%) to the Al2O3 content. The coated samples were characterized by means of an optical microscope, scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and the hardness as well as the bond strength were tested. These results showed that the hardness and porosity decreased with the increasing of the TiO2 content of the Al2O3 + TiO2 coatings. The bonding strength of the coated specimens was increased by using the NiAl bond coat.
- 1 April 2010
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 52 (4) , 252-256
Plasma Spray Coating of an AA 2024-T4 Al Alloy with Oxide Powders
In this study, the surface of AA2024-T4 Al alloy substrate was coated by Al2O3 + TiO2 powders without and with NiAl bond coat by using a plasma spray process. The TiO2 content was added at different concentrations (3, 13 and 40 wt.-%) to the Al2O3 content. The coated samples were characterized by means of an optical microscope, scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and the hardness as well as the bond strength were tested. These results showed that the hardness and porosity decreased with the increasing of the TiO2 content of the Al2O3 + TiO2 coatings. The bonding strength of the coated specimens was increased by using the NiAl bond coat.
- 1 July 2009
- Published by Walter de Gruyter GmbH in Practical Metallography
- Vol. 46 (7) , 337-356
Effects of Heat Treatment on the Machinability of Cr-Ni Stainless Steels with Si and Mn Additives
In this work, the machinability of Cr-Ni austenitic stainless steels with Si and Mn additives was investigated based on tool life and tool wear by turning process without coolant on twelve different specimens in as-cast and heat-treated states. Metal removing process was carried out for four different cutting speeds using HSS cutting tools, while a cutting depth of 1.5 mm and a feed rate of 0.1 mm/min were kept constant. The effects of changes in microstructure with respect to addition elements and heat treatments on the tool wear and the hardness were examined. It was seen that the machinability for all of the specimens was not so good with the tools used. Although the hardness of the materials, which were as-casting, increased slightly with increasing the content of Cr and Ni addition elements, the machinability of these materials was not affected positively or negatively with respect to these elements. As heat treatments increased the hardness of the materials, the optimum tool lives were obtained in the machining of water quenched specimens. It was found that cutting speed was the most influential parameter on tool life.
- 1 July 2009
- Published by Walter de Gruyter GmbH in Practical Metallography
- Vol. 46 (7) , 337-356
Effects of Heat Treatment on the Machinability of Cr-Ni Stainless Steels with Si and Mn Additives
In this work, the machinability of Cr-Ni austenitic stainless steels with Si and Mn additives was investigated based on tool life and tool wear by turning process without coolant on twelve different specimens in as-cast and heat-treated states. Metal removing process was carried out for four different cutting speeds using HSS cutting tools, while a cutting depth of 1.5 mm and a feed rate of 0.1 mm/min were kept constant. The effects of changes in microstructure with respect to addition elements and heat treatments on the tool wear and the hardness were examined. It was seen that the machinability for all of the specimens was not so good with the tools used. Although the hardness of the materials, which were as-casting, increased slightly with increasing the content of Cr and Ni addition elements, the machinability of these materials was not affected positively or negatively with respect to these elements. As heat treatments increased the hardness of the materials, the optimum tool lives were obtained in the machining of water quenched specimens. It was found that cutting speed was the most influential parameter on tool life.
- 1 March 2009
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 51 (3) , 133-140
Wear Behavior of Cu-Cr-Zr Alloy under Electric Current
A Cu-Cr-Zr alloy (Alloy C18150) was investigated for tribological behavior in the presence of electric current flow. Experiments involving adhesive wear were conducted under atmospheric conditions at a constant load of approximately 40 N over a duration of 30 minutes, at three different current values (1 A, 2.5 A and 10 A) and two different DC polarities (%/—), and at three different rotational speeds (1 m/s, 2 m/s and 4.2 m/s). Weight loss measurements were noted and wear behavior was evaluated using surface analysis including SEM and EDS. It was observed that friction speed and its related temperature affected the material loss. It has been considered that the compounds Cr2O3 and Cr2Zr, which form at the surface for positive and negative current flow, respectively, are responsible for this material loss. The wear behavior demonstrated favorable results with current, with wear resistance increasing at higher current intensity, regardless of polarity.
- 1 March 2009
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 51 (3) , 133-140
Wear Behavior of Cu-Cr-Zr Alloy under Electric Current
A Cu-Cr-Zr alloy (Alloy C18150) was investigated for tribological behavior in the presence of electric current flow. Experiments involving adhesive wear were conducted under atmospheric conditions at a constant load of approximately 40 N over a duration of 30 minutes, at three different current values (1 A, 2.5 A and 10 A) and two different DC polarities (%/—), and at three different rotational speeds (1 m/s, 2 m/s and 4.2 m/s). Weight loss measurements were noted and wear behavior was evaluated using surface analysis including SEM and EDS. It was observed that friction speed and its related temperature affected the material loss. It has been considered that the compounds Cr2O3 and Cr2Zr, which form at the surface for positive and negative current flow, respectively, are responsible for this material loss. The wear behavior demonstrated favorable results with current, with wear resistance increasing at higher current intensity, regardless of polarity.
- 1 March 2009
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 51 (3) , 141-146
Properties of Cu/Fe-Mn and Cu/Fe-Cr Metal Matrix Composites Produced by Powder Metallurgy
Ferro-manganese and ferro-chromium particles (FeMnp and FeCrp) were added to a copper matrix and examined for applications requiring wear resistance and rupture strength. Cu/FeMnp, Cu/FeCrp and Cu/FeMnp/FeCrp metal matrix composites (MMCs) were prepared using a powder metallurgy technique to get a homogeneous distribution of particles in controlled amounts. Powders were mixed, compacted, and sintered in a protective argon gas environment. In a wear test, the MMCs showed a favorable resistance to weight loss when pressed against a moving AISI 304 stainless steel wear plate. Rupture strength was determined using a standard transverse rupture test. Fractographs taken of wear and ruptured surfaces together with rupture strength measurements were correlated with the amount and type of particle reinforcement and MMC hardness. The formation of Metal Carbide (MC) and Metal Oxide (MO) around reinforcing particles was also considered. Transverse rupture strength was found to decrease after exceeding a specific amount of reinforcement.
- 1 March 2009
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 51 (3) , 141-146
Properties of Cu/Fe-Mn and Cu/Fe-Cr Metal Matrix Composites Produced by Powder Metallurgy
Ferro-manganese and ferro-chromium particles (FeMnp and FeCrp) were added to a copper matrix and examined for applications requiring wear resistance and rupture strength. Cu/FeMnp, Cu/FeCrp and Cu/FeMnp/FeCrp metal matrix composites (MMCs) were prepared using a powder metallurgy technique to get a homogeneous distribution of particles in controlled amounts. Powders were mixed, compacted, and sintered in a protective argon gas environment. In a wear test, the MMCs showed a favorable resistance to weight loss when pressed against a moving AISI 304 stainless steel wear plate. Rupture strength was determined using a standard transverse rupture test. Fractographs taken of wear and ruptured surfaces together with rupture strength measurements were correlated with the amount and type of particle reinforcement and MMC hardness. The formation of Metal Carbide (MC) and Metal Oxide (MO) around reinforcing particles was also considered. Transverse rupture strength was found to decrease after exceeding a specific amount of reinforcement.
- 1 October 2007
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 49 (10) , 515-523
Investigation of a TIG-Welded Layer Alloyed with Ferromanganese Powder on the Surface of a Copper Alloy
In this study, alloyed layers of 1.5-1.8 mm thickness were formed on the Cu based material surface using the Gas Tungsten Arc welding (GTAW) process. After the preliminary studies and sample preparation as groups I, II, and III, the surface alloying process was performed with 115 A, 125 A and 140 A current values, 6 g, 9 g and 12 g powder feed contents, and by determining voltage coefficients at 25 V and 28 V, respectively. Penetration of ferromanganese on the underlay was ensured using optimized coating parameters. In the ferromanganese layer different hardness values were determined according to the amount of powder fed. These hardness values were correlated to the thermal conductivity of Cu at the respective energy input. The impact resist of the coated specimens was increased. These toughness increments were attributed to newly formed structures in the microstructure with the effect of thermal conductivity and hardness of coated surface. Changes in powder feed time and powder feed rate and energy input were calculated from application parameters.
- 1 October 2007
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 49 (10) , 515-523
Investigation of a TIG-Welded Layer Alloyed with Ferromanganese Powder on the Surface of a Copper Alloy
In this study, alloyed layers of 1.5-1.8 mm thickness were formed on the Cu based material surface using the Gas Tungsten Arc welding (GTAW) process. After the preliminary studies and sample preparation as groups I, II, and III, the surface alloying process was performed with 115 A, 125 A and 140 A current values, 6 g, 9 g and 12 g powder feed contents, and by determining voltage coefficients at 25 V and 28 V, respectively. Penetration of ferromanganese on the underlay was ensured using optimized coating parameters. In the ferromanganese layer different hardness values were determined according to the amount of powder fed. These hardness values were correlated to the thermal conductivity of Cu at the respective energy input. The impact resist of the coated specimens was increased. These toughness increments were attributed to newly formed structures in the microstructure with the effect of thermal conductivity and hardness of coated surface. Changes in powder feed time and powder feed rate and energy input were calculated from application parameters.
- 1 May 2005
- Published by Elsevier in Materials Letters
- Vol. 59 (12) , 1463-1469
Adhesive wear resistance of Cu–Sn–Zn–Pb bronze with additions of Fe, Mn and P
- 1 May 2005
- Published by Elsevier in Materials Letters
- Vol. 59 (12) , 1463-1469
Adhesive wear resistance of Cu–Sn–Zn–Pb bronze with additions of Fe, Mn and P
- 1 June 2002
- Published by Walter de Gruyter GmbH in Zeitschrift für Metallkunde
- Vol. 93 (6) , 572-577
Wear behavior of A356/M7C3and A356/SiC particulate metal matrix composites
- 1 June 2002
- Published by Walter de Gruyter GmbH in Zeitschrift für Metallkunde
- Vol. 93 (6) , 572-577
Wear behavior of A356/M7C3and A356/SiC particulate metal matrix composites
- 1 June 2002
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 124 (1-2) , 113-119
A note on the effect of phosphorus on the microstructure and mechanical properties of leaded-tin bronze
- 1 June 2002
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 124 (1-2) , 113-119
A note on the effect of phosphorus on the microstructure and mechanical properties of leaded-tin bronze
- 1 April 2002
- Published by SAGE Publications in Materials Science and Technology
- Vol. 18 (4) , 401-406
Wear behaviour of ZnAl27/TiCpmetal matrix composites under sliding conditions
- 1 April 2002
- Published by SAGE Publications in Materials Science and Technology
- Vol. 18 (4) , 401-406
Wear behaviour of ZnAl27/TiCpmetal matrix composites under sliding conditions
- 1 February 2002
- Published by SAGE Publications in Materials Science and Technology
- Vol. 18 (2) , 187-192
Microstructure, and mechanical and thermal properties of CuSn/FeCrpmetal matrix composites processed by powder metallurgy
- 1 February 2002
- Published by SAGE Publications in Materials Science and Technology
- Vol. 18 (2) , 187-192
Microstructure, and mechanical and thermal properties of CuSn/FeCrpmetal matrix composites processed by powder metallurgy