Rameez R. Tamboli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rameez R. Tamboli has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Suhash Ranjan Dey
Department of Materials Science and Metallurgical Engineering, Indian Institute of Technology Hyderabad, Kandi, Sangareddy, India
2 shared publications Basanth K. Kodli
Department of Materials Science and Metallurgical Engineering, Indian Institute of Technology Hyderabad, Kandi, Sangareddy, India
1 shared publicationBasudev Bhattacharya
1 shared publication- Benjamin Guennec
Mechanical Engineering Department, Faculty of Engineering Tokyo Denki University Adachi, Tokyo Japan
1 shared publication - Dustin Andersen
Advanced Instrumentation for Nano-Analytics (AINA), MRT Department, Luxembourg Institute of Science and Technology (LIST) , Belvaux , Luxembourg
1 shared publication Hiroshi Fujiwara
1 shared publication
Latest Publications
- 12 June 2022
- Published by Elsevier in Scripta Materialia
- Vol. 219
Quantitative prediction of Al and learning grain boundary character in Al-rich interstitial free steel
- 12 June 2022
- Published by Elsevier in Scripta Materialia
- Vol. 219
Quantitative prediction of Al and learning grain boundary character in Al-rich interstitial free steel
- 11 December 2017
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 4 (2) , 244-254
Texture analyses of friction stir welded austenitic stainless steel AISI-316L
Low stacking fault energy AISI-316L stainless steel of 4 mm thick plates are friction stir welded at 1100 RPM and 8 mm/min welding speed using cubic boron nitride-tungsten rhenium composite tool. Large area orientation image mapping of the stir zone using electron backscatter diffraction scanning electron microscopy is performed to comprehensively characterise its microstructure and is searched for torsion shear texture components. Kernel average misorientation analysis revealed that top layer of the stir zone is almost fully recrystallised which experienced highest temperature and strain; middle layer has more deformed grains than recrystallised, showing partial recrystallisation while the bottom layer which encountered low strain but high temperature is almost fully recrystallised. Texture analyses showed variation from A {111} partial fiber type of texture in the top layer and C {001} and A {1 1} type shear texture components in the middle layer followed by {1 1} < 0> type of shear texture in the bottom layer. It is evident from Kernel average misorientation analysis and texture evolution studies that recrystallised region produced A {111} partial fiber/ {1 1} < 0> shear component while deformed region produced C {001} shear component.
- 11 December 2017
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 4 (2) , 244-254
Texture analyses of friction stir welded austenitic stainless steel AISI-316L
Low stacking fault energy AISI-316L stainless steel of 4 mm thick plates are friction stir welded at 1100 RPM and 8 mm/min welding speed using cubic boron nitride-tungsten rhenium composite tool. Large area orientation image mapping of the stir zone using electron backscatter diffraction scanning electron microscopy is performed to comprehensively characterise its microstructure and is searched for torsion shear texture components. Kernel average misorientation analysis revealed that top layer of the stir zone is almost fully recrystallised which experienced highest temperature and strain; middle layer has more deformed grains than recrystallised, showing partial recrystallisation while the bottom layer which encountered low strain but high temperature is almost fully recrystallised. Texture analyses showed variation from A {111} partial fiber type of texture in the top layer and C {001} and A {1 1} type shear texture components in the middle layer followed by {1 1} < 0> type of shear texture in the bottom layer. It is evident from Kernel average misorientation analysis and texture evolution studies that recrystallised region produced A {111} partial fiber/ {1 1} < 0> shear component while deformed region produced C {001} shear component.