Naohiro Matsukawa
Research Subjects
Research Interests
Naohiro Matsukawa has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
H. Nozawa
Semiconductor Device Engineering Laboratory, Toshiba Corporation, 1, Komukai Toshiba-cho, Saiwai-ku, Kawasaki, Japan 210
7 shared publicationsJ. Matsunaga
4 shared publicationsS. Kohyama
4 shared publicationsK. Masuda
3 shared publicationsS. Morita
Semiconductor Device Engineering Laboratory, Toshiba Corporation, 1, Komukai Toshiba-cho, Saiwai-ku, Kawasaki, Japan 210
3 shared publicationsH. Araki
2 shared publications
Latest Publications
- 24 September 2008
- Published by Japan Society of Applied Physics
Distributed-cycling Effects for Data Retention Characteristics of Flash Memories
2008 International Conference on Solid State Devices and Materials,Search for presentations
- 24 September 2008
- Published by Japan Society of Applied Physics
Distributed-cycling Effects for Data Retention Characteristics of Flash Memories
2008 International Conference on Solid State Devices and Materials,Search for presentations
- 19 November 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 283-287
A new technique for measuring threshold voltage distribution in flash EEPROM devices
- 19 November 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 283-287
A new technique for measuring threshold voltage distribution in flash EEPROM devices
- 1 September 1999
- Published by Elsevier in Microelectronic Engineering
- Vol. 48 (1-4) , 121-124
A new model for TDDB lifetime distribution of SiO2
- 1 September 1999
- Published by Elsevier in Microelectronic Engineering
- Vol. 48 (1-4) , 121-124
A new model for TDDB lifetime distribution of SiO2
- 1 November 1996
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 43 (11) , 1924-1929
A hot hole-induced low-level leakage current in thin silicon dioxide films
A new kind of stress-induced low-level leakage current (LLLC) in thin silicon dioxide is reported. It is observed after the stress of hot hole injection at the gate edge. Since voltage dependence of this new kind of LLLC is steeper than that of conventional FN stress-induced LLLC, each conduction mechanism may be different. This LLLC is reduced by both hot electron injection and UV irradiation. These reductions are never observed in FN stress-induced LLLC. The most promising mechanism is sequential tunneling via trapped holes.
- 1 November 1996
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 43 (11) , 1924-1929
A hot hole-induced low-level leakage current in thin silicon dioxide films
A new kind of stress-induced low-level leakage current (LLLC) in thin silicon dioxide is reported. It is observed after the stress of hot hole injection at the gate edge. Since voltage dependence of this new kind of LLLC is steeper than that of conventional FN stress-induced LLLC, each conduction mechanism may be different. This LLLC is reduced by both hot electron injection and UV irradiation. These reductions are never observed in FN stress-induced LLLC. The most promising mechanism is sequential tunneling via trapped holes.
- 1 January 1990
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 127-128
Process technologies for a 16 ns high speed 1 Mb CMOS EPROM
- 1 January 1990
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 127-128
Process technologies for a 16 ns high speed 1 Mb CMOS EPROM
- 1 January 1990
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 25 (5) , 1141-1146
A 16-ns 1-Mb CMOS EPROM
- 1 January 1990
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 25 (5) , 1141-1146
A 16-ns 1-Mb CMOS EPROM
- 1 January 1987
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 556-559
Novel process and device technologies for submicron 4Mb CMOS EPROMs
High performance and reliable submicron EPROM technologies to realize 4Mb density and fast operation speed have been developed. The main key process technologies are (a) thin reliable inter-poly dielectrics, (b) SAC (Self Aligned Contact) using RTA (Rapid Thermal Annealing), and (c) low resistance polycide gate. The device uses 0.8µm N-well CMOS technology. Masked MLDD(Moderately Lightly Doped Drain) NMOS transistors are used in peripheral circuits. Submicron EPROM cell offers sufficiently fast write speed and soft-write endurance.
- 1 January 1987
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 556-559
Novel process and device technologies for submicron 4Mb CMOS EPROMs
High performance and reliable submicron EPROM technologies to realize 4Mb density and fast operation speed have been developed. The main key process technologies are (a) thin reliable inter-poly dielectrics, (b) SAC (Self Aligned Contact) using RTA (Rapid Thermal Annealing), and (c) low resistance polycide gate. The device uses 0.8µm N-well CMOS technology. Masked MLDD(Moderately Lightly Doped Drain) NMOS transistors are used in peripheral circuits. Submicron EPROM cell offers sufficiently fast write speed and soft-write endurance.
- 1 April 1986
- Published by Institute of Electrical and Electronics Engineers (IEEE) in 8th Reliability Physics Symposium
- No. 07350791,p. 247-252
Reliability of Thin Oxide Grown on Heavily Doped Polysilicon
The reliability of 100 - 200 A poly-oxide grown on heavily doped polysilicon was investigated mainly by TDDB measurements, compared with ~ 100 A tunnel oxide grown on high dose implanted Si substrate. For the lower phosphorus concentration polyoxide, cumulative failure rate is high at short stress time, slightly depending on stress electric field. The poly-oxide for the higher concentration wears out under the high stress electric field. The wearout phenomenon is considered to be attributed to positive charge generation, due to phosphorus atoms incorporated into poly-oxide. No wearout is observed for tunnel oxide on high dose implanted Si substrate. The TDDB characteristics can be explained by reduction in effective thickness for stoichiometric oxide.
- 1 April 1986
- Published by Institute of Electrical and Electronics Engineers (IEEE) in 8th Reliability Physics Symposium
- No. 07350791,p. 247-252
Reliability of Thin Oxide Grown on Heavily Doped Polysilicon
The reliability of 100 - 200 A poly-oxide grown on heavily doped polysilicon was investigated mainly by TDDB measurements, compared with ~ 100 A tunnel oxide grown on high dose implanted Si substrate. For the lower phosphorus concentration polyoxide, cumulative failure rate is high at short stress time, slightly depending on stress electric field. The poly-oxide for the higher concentration wears out under the high stress electric field. The wearout phenomenon is considered to be attributed to positive charge generation, due to phosphorus atoms incorporated into poly-oxide. No wearout is observed for tunnel oxide on high dose implanted Si substrate. The TDDB characteristics can be explained by reduction in effective thickness for stoichiometric oxide.
- 1 February 1986
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 33 (2) , 275-281
An EEPROM cell using a low barrier height tunnel oxide
A new simple method to fabricate a thin oxide with low barrier height is proposed. An oxide is grown on a heavily implanted silicon substrate with As or P in excess of 5 × 10 14 /cm 2 . When the oxide was grown in H 2 O + Ar gas after Ar annealing, the barrier height of the oxide conduction band with respect to the silicon conduction band decreased to 1.8 eV, about one half of the ordinary value of 3.2 eV. This phenomenon was applied to an EEPROM cell, which showed superior WRITE/ERASE characteristics. A moderately implanted As (2.5 × 10 15 / cm 2 ) sample shows excellent WRITE/ERASE endurance, over 10 6 cycles with 2-V V th window, which could not realized by using an ordinary oxide.
- 1 February 1986
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 33 (2) , 275-281
An EEPROM cell using a low barrier height tunnel oxide
A new simple method to fabricate a thin oxide with low barrier height is proposed. An oxide is grown on a heavily implanted silicon substrate with As or P in excess of 5 × 10 14 /cm 2 . When the oxide was grown in H 2 O + Ar gas after Ar annealing, the barrier height of the oxide conduction band with respect to the silicon conduction band decreased to 1.8 eV, about one half of the ordinary value of 3.2 eV. This phenomenon was applied to an EEPROM cell, which showed superior WRITE/ERASE characteristics. A moderately implanted As (2.5 × 10 15 / cm 2 ) sample shows excellent WRITE/ERASE endurance, over 10 6 cycles with 2-V V th window, which could not realized by using an ordinary oxide.