Shin-Ichiro Kawasaki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shin-Ichiro Kawasaki has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
Akira Suzuki
New Industry Creation Hatchery Center (NICHe), Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-0812, Japan
14 shared publicationsKiwamu Sue
Reseach Institute for Chemical Process Technology, National Institute of Advanced Industrial Science and Technology (AIST) Nigatake 4-2-1, Miyagino-ku, Sendai, JAPAN, 985-8551
10 shared publications- Tatsuya Fujii
Research Institute for Chemical Process Technology, National Institute of Advanced Industrial Science and Technology (AIST), 4-2-1 Nigatake, Miyagino-ku, Sendai, Miyagi 983-8551, Japan
9 shared publications Ryuto Ookawara
6 shared publications- Yukiya Hakuta
Advanced Operando-Measurement Technology Open Innovation Laboratory, National Institute of Advanced Industrial Science and Technology (AIST), 5-1-5 Kashiwanoha, Chiba, 277-8589, JAPAN
6 shared publications Kunio Arai
Tohoku University
5 shared publications
Latest Publications
- Open Access
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Visualization of paint spray using high-pressure CO2
This study investigates a CO₂-assisted painting technology in which high-pressure carbon dioxide is dissolved into paint to reduce its viscosity and subsequently sprayed continuously into an atmospheric-pressure environment. Spray behavior was analyzed through optical visualization and cross-sectional imaging to clarify the spray morphology resulting from rapid CO₂ depressurization and to assess the influence of nozzle geometry.,The results show that, upon depressurization, dissolved CO₂ vaporizes and significantly alters the spray structure. The spray mist produced spreads much less in thickness and forms a thin, leaf-like structure that appears to be enveloped by a CO₂-rich gas phase. This CO₂ envelope suppresses the lateral spread of the spray mist. Although a detailed quantitative analysis is required, the observed spray is clearly CO₂-rich, suggesting a local oxygen-displacement effect in the atomization region. This phenomenon may contribute to a reduced ignition risk during spraying of flammable paints.
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessVisualization of paint spray using high-pressure CO2
This study investigates a CO₂-assisted painting technology in which high-pressure carbon dioxide is dissolved into paint to reduce its viscosity and subsequently sprayed continuously into an atmospheric-pressure environment. Spray behavior was analyzed through optical visualization and cross-sectional imaging to clarify the spray morphology resulting from rapid CO₂ depressurization and to assess the influence of nozzle geometry.,The results show that, upon depressurization, dissolved CO₂ vaporizes and significantly alters the spray structure. The spray mist produced spreads much less in thickness and forms a thin, leaf-like structure that appears to be enveloped by a CO₂-rich gas phase. This CO₂ envelope suppresses the lateral spread of the spray mist. Although a detailed quantitative analysis is required, the observed spray is clearly CO₂-rich, suggesting a local oxygen-displacement effect in the atomization region. This phenomenon may contribute to a reduced ignition risk during spraying of flammable paints.
- Open Access
- 29 April 2026
- Published by Elsevier in SSRN Electronic Journal
Development of a Continuous Lignin Separation System Using Subcritical Water
In this study, subcritical water treatment was performed using cedar wood powder slurry under conditions of reaction temperature 300oC, pressure 10 MPa, and residence time 30 minutes. The objective of this study was component separation from woody biomass. A pilot plant-scale apparatus was constructed as a continuous treatment system. A system was adopted in which wood powder slurry was semi-continuously supplied to a cylindrical reactor heated with a heat transfer medium. Inside the reactor, a screw-shaped shaft that generates an upward flow was installed in the lower third, and a scraper-type heat exchanger that provides rotational stirring function was installed from the center to the upper two-thirds. Stable continuous treatment was achieved by supplying a solid slurry with a concentration of 15 wt%. The reaction products were separated using a high-temperature filter into low molecular weight lignin (resin-grade lignin) that is completely soluble in acetone and high molecular weight lignin that is recovered as a solid. The treated liquid was continuously recovered under high pressure using a high-pressure receiver with an internal piston mechanism. Wood powder is mainly composed of lignin, but it also contains cellulose and hemicellulose. It is believed that subcritical water treatment over-decomposes components other than lignin to the level of organic acids. The treated liquid was recovered as a paste of low molecular weight lignin. This pilot plant successfully achieved continuous operation for more than 12 hours.
- 29 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDevelopment of a Continuous Lignin Separation System Using Subcritical Water
In this study, subcritical water treatment was performed using cedar wood powder slurry under conditions of reaction temperature 300oC, pressure 10 MPa, and residence time 30 minutes. The objective of this study was component separation from woody biomass. A pilot plant-scale apparatus was constructed as a continuous treatment system. A system was adopted in which wood powder slurry was semi-continuously supplied to a cylindrical reactor heated with a heat transfer medium. Inside the reactor, a screw-shaped shaft that generates an upward flow was installed in the lower third, and a scraper-type heat exchanger that provides rotational stirring function was installed from the center to the upper two-thirds. Stable continuous treatment was achieved by supplying a solid slurry with a concentration of 15 wt%. The reaction products were separated using a high-temperature filter into low molecular weight lignin (resin-grade lignin) that is completely soluble in acetone and high molecular weight lignin that is recovered as a solid. The treated liquid was continuously recovered under high pressure using a high-pressure receiver with an internal piston mechanism. Wood powder is mainly composed of lignin, but it also contains cellulose and hemicellulose. It is believed that subcritical water treatment over-decomposes components other than lignin to the level of organic acids. The treated liquid was recovered as a paste of low molecular weight lignin. This pilot plant successfully achieved continuous operation for more than 12 hours.
- Open Access
- 17 February 2026
- Published by Elsevier in SSRN Electronic Journal
Development of Stable Spray Technology through Homogeneous Mixing Using a Multi-Stage Segmented Micromixer Suitable for Blending Molten Resin and High-Pressure CO2
We developed a technology to obtain resin microparticles by continuously supplying molten polyethylene glycol (PEG) resins PEG6000 and PEG20000 mixing them with high-pressure CO2, reducing the molten resin's viscosity, and rapidly ejecting the mixture from a high-pressure environment to atmospheric pressure.The key point of this technology is how to uniformly mix high-pressure CO2 into a high-viscosity fluid. This study developed a multi-stage split-channel micro-mixer to uniformly mix two fluids with a very large viscosity difference, such as a high-viscosity fluid and high-pressure CO2. High-pressure CO2 and molten resin are each uniformly divided and fed into separate channels. Within the micro-channel network, high-pressure CO2 is mixed into the molten resin. The channels undergo contraction and homogenization. Subsequently, non-adjacent channels are divided into dozens of smaller channels, where the mixture is further blended to form a uniform fluid. Here, whether the high-pressure CO2 is dissolved in the resin is not the issue; what is important is achieving a uniform fluid.Furthermore, by measuring this uniformity with a high-pressure differential pressure gauge, it was possible to verify that the fluid maintains its homogeneity. Ultimately, using a multi-stage split-channel micro-mixer, when ejected from the high-pressure environment to atmospheric pressure, the resulting particles were as follows: for PEG6000, the primary particles were smooth-surfaced spherical particles of approximately 10μm, and their aggregates yielded particles averaging about 50μm.For PEG20000, the primary particles were roughly 100μm in size with a rough surface, forming lump-like aggregates. Uniform particles were continuously obtained.
- 17 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDevelopment of Stable Spray Technology through Homogeneous Mixing Using a Multi-Stage Segmented Micromixer Suitable for Blending Molten Resin and High-Pressure CO2
We developed a technology to obtain resin microparticles by continuously supplying molten polyethylene glycol (PEG) resins PEG6000 and PEG20000 mixing them with high-pressure CO2, reducing the molten resin's viscosity, and rapidly ejecting the mixture from a high-pressure environment to atmospheric pressure.The key point of this technology is how to uniformly mix high-pressure CO2 into a high-viscosity fluid. This study developed a multi-stage split-channel micro-mixer to uniformly mix two fluids with a very large viscosity difference, such as a high-viscosity fluid and high-pressure CO2. High-pressure CO2 and molten resin are each uniformly divided and fed into separate channels. Within the micro-channel network, high-pressure CO2 is mixed into the molten resin. The channels undergo contraction and homogenization. Subsequently, non-adjacent channels are divided into dozens of smaller channels, where the mixture is further blended to form a uniform fluid. Here, whether the high-pressure CO2 is dissolved in the resin is not the issue; what is important is achieving a uniform fluid.Furthermore, by measuring this uniformity with a high-pressure differential pressure gauge, it was possible to verify that the fluid maintains its homogeneity. Ultimately, using a multi-stage split-channel micro-mixer, when ejected from the high-pressure environment to atmospheric pressure, the resulting particles were as follows: for PEG6000, the primary particles were smooth-surfaced spherical particles of approximately 10μm, and their aggregates yielded particles averaging about 50μm.For PEG20000, the primary particles were roughly 100μm in size with a rough surface, forming lump-like aggregates. Uniform particles were continuously obtained.
- 5 September 2025
- Published by Elsevier in The Journal of Supercritical Fluids
- Vol. 228
Effect of residence time and different micro-mixers on supercritical CO2 extraction of vanillin from aqueous solution
- 5 September 2025
- Published by Elsevier in The Journal of Supercritical Fluids
- Vol. 228
Effect of residence time and different micro-mixers on supercritical CO2 extraction of vanillin from aqueous solution
- Open Access
- 12 April 2022
- Published by MDPI AG in Separations
- Vol. 9 (4) , 97
Generation of Controlled Liquid–Liquid Slug Flow by Interlocking Two Diaphragm Pumps
From the viewpoint of resource and energy-saving, the high extraction rate of alternating liquid–liquid flow (slug flow) is important given that it enables its novel use in extraction. Additionally, a specific extraction rate must be maintained for the practical application of slug flow to chemical extraction. Although slug flow is easily generated, controlling the slug length is difficult. In this study, two diaphragm pumps were interlocked to generate a slug flow. By linking the movement of the diaphragms of the two pumps, we could successfully and efficiently control the slug length, and the interlocking diaphragms could easily control the length of the aqueous and oil phase segments of the slug flow. The lengths of the aqueous and oil phases of the slug flow, which could not be quantitatively controlled, could be expressed in terms of the linear velocity of the liquid, the kinematic viscosity, and the tube diameter using the Reynolds number. This relation aids the extraction equipment design using slug flow. Furthermore, the mass transfer coefficient of extraction obtained using the slug flow generated by the developed device was similar to that obtained by the conventional method of a syringe pump. These results indicate that slug flow can be successfully applied to extraction processes.
- 12 April 2022
- Published by MDPI AG in Separations
- Vol. 9 (4) , 97
Open AccessGeneration of Controlled Liquid–Liquid Slug Flow by Interlocking Two Diaphragm Pumps
From the viewpoint of resource and energy-saving, the high extraction rate of alternating liquid–liquid flow (slug flow) is important given that it enables its novel use in extraction. Additionally, a specific extraction rate must be maintained for the practical application of slug flow to chemical extraction. Although slug flow is easily generated, controlling the slug length is difficult. In this study, two diaphragm pumps were interlocked to generate a slug flow. By linking the movement of the diaphragms of the two pumps, we could successfully and efficiently control the slug length, and the interlocking diaphragms could easily control the length of the aqueous and oil phase segments of the slug flow. The lengths of the aqueous and oil phases of the slug flow, which could not be quantitatively controlled, could be expressed in terms of the linear velocity of the liquid, the kinematic viscosity, and the tube diameter using the Reynolds number. This relation aids the extraction equipment design using slug flow. Furthermore, the mass transfer coefficient of extraction obtained using the slug flow generated by the developed device was similar to that obtained by the conventional method of a syringe pump. These results indicate that slug flow can be successfully applied to extraction processes.
- 14 October 2021
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 6 (12) , 2248-2252
A continuous flow process for biaryls based on sequential Suzuki–Miyaura coupling and supercritical carbon dioxide extraction
A continuous flow process for the production of biaryls based on the seamless coupling of a packed-bed reactor (synthesis module) and a rapid supercritical CO2 extraction system (extraction module) is reported.
- 14 October 2021
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 6 (12) , 2248-2252
A continuous flow process for biaryls based on sequential Suzuki–Miyaura coupling and supercritical carbon dioxide extraction
A continuous flow process for the production of biaryls based on the seamless coupling of a packed-bed reactor (synthesis module) and a rapid supercritical CO2 extraction system (extraction module) is reported.
- 10 April 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 57 (16) , 5717-5721
Rapid Continuous Supercritical CO2 Extraction and Separation of Organic Compounds from Liquid Solutions
- 10 April 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 57 (16) , 5717-5721
Rapid Continuous Supercritical CO2 Extraction and Separation of Organic Compounds from Liquid Solutions
- 1 December 2017
- Published by Elsevier in The Journal of Supercritical Fluids
- Vol. 130, 172-175
Development of a solvent selection guide for CO 2 spray coating
- 1 December 2017
- Published by Elsevier in The Journal of Supercritical Fluids
- Vol. 130, 172-175
Development of a solvent selection guide for CO 2 spray coating
- 18 October 2017
- Published by Springer Nature in Frontiers of Chemical Science and Engineering
- Vol. 12 (1) , 184-193
Micronization of curcumin with biodegradable polymer by supercritical anti-solvent using micro swirl mixer
- 18 October 2017
- Published by Springer Nature in Frontiers of Chemical Science and Engineering
- Vol. 12 (1) , 184-193
Micronization of curcumin with biodegradable polymer by supercritical anti-solvent using micro swirl mixer