Pablo Navarro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pablo Navarro has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
S. Marguet
15 shared publicationsJ.-F. Ferrero
10 shared publicationsJ. Aubry
Université de Toulouse; INSA, UPS, Mines Albi, ISAE; ICA (Institut Clément Ader), 10 avenue Edouard Belin, BP54032, 31055 Toulouse Cedex 4, France
8 shared publicationsF. Pascal
6 shared publicationsP. Rauch
6 shared publicationsS. Lemaire
6 shared publications
Latest Publications
- 4 September 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 238 (4) , 766-780
Dynamic response of epoxy foam structures reinforced with aramid layers subjected to low-velocity impact
This study investigates the impact response of epoxy foam structures reinforced with aramid woven fabrics through drop weight tests. These structures are not classical sandwich panels as the fabrics are blended into the epoxy foam. The number of aramid plies and their location are varied, and the influence of the foam density is studied. Low-velocity drop weight tests are conducted. The load–displacement curves, the morphology of damage, the indentation, and the back face signature are analyzed. Results reveal that increasing the number of aramid layers in the middle of the structure reduces the crack propagation and increases the peak load. In addition, adding one layer of aramid at the back face prevents the crack propagation. Finally, the use of several foam densities, with the higher density at the impact face leads to an improved protection capacity.
- 4 September 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 238 (4) , 766-780
Dynamic response of epoxy foam structures reinforced with aramid layers subjected to low-velocity impact
This study investigates the impact response of epoxy foam structures reinforced with aramid woven fabrics through drop weight tests. These structures are not classical sandwich panels as the fabrics are blended into the epoxy foam. The number of aramid plies and their location are varied, and the influence of the foam density is studied. Low-velocity drop weight tests are conducted. The load–displacement curves, the morphology of damage, the indentation, and the back face signature are analyzed. Results reveal that increasing the number of aramid layers in the middle of the structure reduces the crack propagation and increases the peak load. In addition, adding one layer of aramid at the back face prevents the crack propagation. Finally, the use of several foam densities, with the higher density at the impact face leads to an improved protection capacity.
- 25 September 2022
- Published by Springer Nature
- p. 593-604
Optimizing Racing Wheelchair Design Through Coupled Biomechanical-Mechanical Simulation
- 25 September 2022
- Published by Springer Nature
- p. 593-604
Optimizing Racing Wheelchair Design Through Coupled Biomechanical-Mechanical Simulation
- 1 April 2018
- Published by Elsevier in Composite Structures
- Vol. 190, 32-42
Impact damage prediction in thin woven composite laminates – Part I: Modeling strategy and validation
- 1 April 2018
- Published by Elsevier in Composite Structures
- Vol. 190, 32-42
Impact damage prediction in thin woven composite laminates – Part I: Modeling strategy and validation
- 1 April 2018
- Published by Elsevier in Composite Structures
- Vol. 190, 43-51
Impact damage prediction in thin woven composite laminates – Part II: Application to normal and oblique impacts on sandwich structure
- 1 April 2018
- Published by Elsevier in Composite Structures
- Vol. 190, 43-51
Impact damage prediction in thin woven composite laminates – Part II: Application to normal and oblique impacts on sandwich structure
- 1 December 2017
- Published by Elsevier in Composites Part B: Engineering
- Vol. 130, 147-157
Semi-continuous strategy for the modelling of damage mechanisms in unidirectional composites under low velocity impacts
- 1 December 2017
- Published by Elsevier in Composites Part B: Engineering
- Vol. 130, 147-157
Semi-continuous strategy for the modelling of damage mechanisms in unidirectional composites under low velocity impacts
- 1 October 2017
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 78, 135-147
Experimental & numerical study of the Tensile/Compression-Shear Arcan test under dynamic loading
- 1 October 2017
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 78, 135-147
Experimental & numerical study of the Tensile/Compression-Shear Arcan test under dynamic loading
- 26 May 2016
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 20 (1) , 106-129
Experimental results of medium velocity impact tests for reinforced foam core braided composite structures
Absorbing impact energy at subsystem level is an attractive idea that is emphasized by new composite reinforcement techniques such as stitching or pinning. This paper reports experimental results of medium velocity impact tests carried out on several arrangements of reinforced foam/braided composite structures. The tests consisted of a steel ball shot at a velocity of 110 m/s from a gas gun impacting the structures on their leading edge. Post-mortem tomography analysis delivered very rich information which shed light on the damage mechanisms that the composite structures underwent. In addition, two fast-speed cameras were used to derive the energy absorption during the impact. Absorption capabilities were also compared with those of dynamic crushing tests (reported in a companion paper) and some designs clearly exhibited promising behavior as shock absorbers.
- 26 May 2016
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 20 (1) , 106-129
Experimental results of medium velocity impact tests for reinforced foam core braided composite structures
Absorbing impact energy at subsystem level is an attractive idea that is emphasized by new composite reinforcement techniques such as stitching or pinning. This paper reports experimental results of medium velocity impact tests carried out on several arrangements of reinforced foam/braided composite structures. The tests consisted of a steel ball shot at a velocity of 110 m/s from a gas gun impacting the structures on their leading edge. Post-mortem tomography analysis delivered very rich information which shed light on the damage mechanisms that the composite structures underwent. In addition, two fast-speed cameras were used to derive the energy absorption during the impact. Absorption capabilities were also compared with those of dynamic crushing tests (reported in a companion paper) and some designs clearly exhibited promising behavior as shock absorbers.
- 22 February 2016
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 30 (12) , 1319-1339
Numerical study of the local behaviour of adhesive bonds under dynamic loading
Nowadays, adhesively bonded structures are widely used in the transport sector for the development of lightweight vehicles. In order to guarantee passenger safety, it is thus necessary to understand the behaviour of such assemblies under dynamic and combined loadings. This paper presents a numerical study of the local behaviour of adhesively bonded assemblies under dynamic loading. In the first part, the ASTM D950-03 block impact test is studied. This device does not enable a homogeneous loading of the adhesive and causes stress concentrations. On the basis of existing quasi-static works, strategies are then implemented at a local scale. By combining a specific substrate geometry and by limiting the stiffness gradient between the substrates and the adhesive, results show that it is possible to obtain a qualitatively acceptable stress fields in the adhesive for mechanical characterization under dynamic loadings. The Arcan TCS device mentioned below uses such solutions to characterize the mechanical behaviour of bonded joints subjected to combined quasi-static loadings. In this study, the question of its extensibility to dynamic loadings by the use of an impactor guided into a drop tower is investigated. A dedicated finite element model is built under the plane stress assumption. The stress distributions in the adhesive are analysed through time and space for several loading conditions. The stress versus time signals are then compared with the results coming from modal analysis in order to highlight the vibration behaviour of the device, directly linked to the configuration.
- 22 February 2016
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 30 (12) , 1319-1339
Numerical study of the local behaviour of adhesive bonds under dynamic loading
Nowadays, adhesively bonded structures are widely used in the transport sector for the development of lightweight vehicles. In order to guarantee passenger safety, it is thus necessary to understand the behaviour of such assemblies under dynamic and combined loadings. This paper presents a numerical study of the local behaviour of adhesively bonded assemblies under dynamic loading. In the first part, the ASTM D950-03 block impact test is studied. This device does not enable a homogeneous loading of the adhesive and causes stress concentrations. On the basis of existing quasi-static works, strategies are then implemented at a local scale. By combining a specific substrate geometry and by limiting the stiffness gradient between the substrates and the adhesive, results show that it is possible to obtain a qualitatively acceptable stress fields in the adhesive for mechanical characterization under dynamic loadings. The Arcan TCS device mentioned below uses such solutions to characterize the mechanical behaviour of bonded joints subjected to combined quasi-static loadings. In this study, the question of its extensibility to dynamic loadings by the use of an impactor guided into a drop tower is investigated. A dedicated finite element model is built under the plane stress assumption. The stress distributions in the adhesive are analysed through time and space for several loading conditions. The stress versus time signals are then compared with the results coming from modal analysis in order to highlight the vibration behaviour of the device, directly linked to the configuration.
- 1 December 2015
- Published by Elsevier in Composite Structures
- Vol. 134, 302-310
On the modelling of low to medium velocity impact onto woven composite materials with a 2D semi-continuous approach
- 1 December 2015
- Published by Elsevier in Composite Structures
- Vol. 134, 302-310
On the modelling of low to medium velocity impact onto woven composite materials with a 2D semi-continuous approach
- 1 September 2015
- Published by Elsevier in Composites Part B: Engineering
- Vol. 78, 244-255
Experimental study of impact energy absorption by reinforced braided composite structures: Dynamic crushing tests
- 1 September 2015
- Published by Elsevier in Composites Part B: Engineering
- Vol. 78, 244-255
Experimental study of impact energy absorption by reinforced braided composite structures: Dynamic crushing tests