Ryan Hood
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ryan Hood has a total of 147 co-authors. Here are the top co-authors by number of shared publications:
- Cedric Kar Wai Tsui
Sandia National Laboratories
6 shared publications - Filippo Scotti
Lawrence Livermore National Laboratory
5 shared publications - Alessandro Bortolon
Princeton Plasma Physics Laboratory
4 shared publications - Fenton Glass
General Atomics, San Diego, CA, United States of America
4 shared publications - Gilson Ronchi
Oak Ridge National Laboratory
4 shared publications - Igor Bykov
General Atomics 2 , San Diego, California 92121
4 shared publications
Latest Publications
- Open Access
- 10 November 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (45) , 455602
Micro-trench measurement of selective boron deposition during boron powder dropper operation in DIII-D
The selective boron (B) deposition rate is reported as measured using the micro-trench method in the DIII-D divertor during deuterium (D) H-mode outer strike point (OSP) sweeping plasma discharges with B powder injection via the impurity powder dropper (IPD). The selective deposition is defined as a result of B deposition and impurity sputtering (deposited B sputtered by B ions or other impurity ion species) in a micro-scale region geometrically shadowed from direct fuel/D + ion bombardment. To perform this work, micro-trenches 32 μ m × 32 μ m × 4 μ m deep were fabricated on a single-crystal silicon sample. The sample was exposed to DIII-D H-mode ‘cleaning’ plasma discharges with D fueling and OSP sweeping via the divertor material evaluation system (DiMES). The IPD injected B powder at rates of 5–20 mg s −1 during 2–5 s of H-mode plasmas in multiple discharges, adding up to 0.4 g injected in total. Injected B powders were ablated, ionized, and transported to PFC surfaces. Post-mortem analysis revealed that impurity deposition concentrated in a D + ion shadowed area on the micro-trench floor, while no B deposition was observed outside of the micro-trench, which implied that net impurity deposition can be significantly enhanced by rough micro-structures on PFC surfaces, i.e. selective deposition. An energy-dispersive X-ray spectroscopy (EDS) analysis detected impurity deposition containing B, carbon, oxygen, and silicon. Combining the impurity deposition height profile measured by atomic force microscopy and the relative B concentration profiles measured by EDS, we determined the selective B deposition thickness of ∼25 nm in the diverter region. The measured B deposition thickness agreed with a mass balance analysis to within half the magnitude when the B impurity flux was assumed to be concentrated near the OSP, as predicted by a real-time wall conditioning model developed to optimize IPD operations of advanced fusion reactors.
- 10 November 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (45) , 455602
Open AccessMicro-trench measurement of selective boron deposition during boron powder dropper operation in DIII-D
The selective boron (B) deposition rate is reported as measured using the micro-trench method in the DIII-D divertor during deuterium (D) H-mode outer strike point (OSP) sweeping plasma discharges with B powder injection via the impurity powder dropper (IPD). The selective deposition is defined as a result of B deposition and impurity sputtering (deposited B sputtered by B ions or other impurity ion species) in a micro-scale region geometrically shadowed from direct fuel/D + ion bombardment. To perform this work, micro-trenches 32 μ m × 32 μ m × 4 μ m deep were fabricated on a single-crystal silicon sample. The sample was exposed to DIII-D H-mode ‘cleaning’ plasma discharges with D fueling and OSP sweeping via the divertor material evaluation system (DiMES). The IPD injected B powder at rates of 5–20 mg s −1 during 2–5 s of H-mode plasmas in multiple discharges, adding up to 0.4 g injected in total. Injected B powders were ablated, ionized, and transported to PFC surfaces. Post-mortem analysis revealed that impurity deposition concentrated in a D + ion shadowed area on the micro-trench floor, while no B deposition was observed outside of the micro-trench, which implied that net impurity deposition can be significantly enhanced by rough micro-structures on PFC surfaces, i.e. selective deposition. An energy-dispersive X-ray spectroscopy (EDS) analysis detected impurity deposition containing B, carbon, oxygen, and silicon. Combining the impurity deposition height profile measured by atomic force microscopy and the relative B concentration profiles measured by EDS, we determined the selective B deposition thickness of ∼25 nm in the diverter region. The measured B deposition thickness agreed with a mass balance analysis to within half the magnitude when the B impurity flux was assumed to be concentrated near the OSP, as predicted by a real-time wall conditioning model developed to optimize IPD operations of advanced fusion reactors.
- 3 November 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 234
Design of a closed divertor with mid-leg pumping for core-edge integration in DIII-D
- 3 November 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 234
Design of a closed divertor with mid-leg pumping for core-edge integration in DIII-D
- Open Access
- 7 October 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (12) , 126041
Poloidal asymmetries of main chamber neutral fueling in DIII-D ELMy H-mode plasmas
Understanding poloidal asymmetries in main chamber neutral fueling is essential for characterizing the balance between particle sources and transport in the formation of the H-mode density pedestal. The primary goal of this work is to study changes in these fueling asymmetries and their relationship to divertor recycling across different magnetic configurations in DIII-D lower single-null (LSN) type-I ELMy H-mode plasmas, using direct measurements of the pedestal ionization source obtained with the LLAMA (Lyman-alpha Measurement Apparatus) diagnostic. By combining these direct measurements of the neutral population and studying how it influences the pedestal density structure and overall pedestal performance, this work aims to provide new insights into the role of neutrals in H-mode pedestal physics. We find that the main chamber ionization on the high-field-side (HFS) strongly dominates when the ion ∇ B drift is in the favorable direction. In contrast, reversing the drift direction to the unfavorable direction significantly reduces HFS fueling, that is only partially compensated by a moderate increase in low-field-side (LFS) fueling. The resulting changes in the edge particle source are accompanied by a decrease in pedestal electron density and an increase in pedestal temperature, such that the pedestal pressure remains approximately unchanged. Measurements of divertor recycling and divertor radiation indicate that these fueling asymmetries are also linked to the divertor regime. In particular, inner divertor detachment in the favorable drift configuration decouples main chamber fueling on the HFS from target recycling, while attached divertor conditions in unfavorable drift cases lead to a strong correlation between divertor recycling and main chamber fueling asymmetries. These results suggest that the ion ∇ B drift direction, by modifying main chamber fueling, can influence the pedestal density structure and overall pedestal performance.
- 7 October 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (12) , 126041
Open AccessPoloidal asymmetries of main chamber neutral fueling in DIII-D ELMy H-mode plasmas
Understanding poloidal asymmetries in main chamber neutral fueling is essential for characterizing the balance between particle sources and transport in the formation of the H-mode density pedestal. The primary goal of this work is to study changes in these fueling asymmetries and their relationship to divertor recycling across different magnetic configurations in DIII-D lower single-null (LSN) type-I ELMy H-mode plasmas, using direct measurements of the pedestal ionization source obtained with the LLAMA (Lyman-alpha Measurement Apparatus) diagnostic. By combining these direct measurements of the neutral population and studying how it influences the pedestal density structure and overall pedestal performance, this work aims to provide new insights into the role of neutrals in H-mode pedestal physics. We find that the main chamber ionization on the high-field-side (HFS) strongly dominates when the ion ∇ B drift is in the favorable direction. In contrast, reversing the drift direction to the unfavorable direction significantly reduces HFS fueling, that is only partially compensated by a moderate increase in low-field-side (LFS) fueling. The resulting changes in the edge particle source are accompanied by a decrease in pedestal electron density and an increase in pedestal temperature, such that the pedestal pressure remains approximately unchanged. Measurements of divertor recycling and divertor radiation indicate that these fueling asymmetries are also linked to the divertor regime. In particular, inner divertor detachment in the favorable drift configuration decouples main chamber fueling on the HFS from target recycling, while attached divertor conditions in unfavorable drift cases lead to a strong correlation between divertor recycling and main chamber fueling asymmetries. These results suggest that the ion ∇ B drift direction, by modifying main chamber fueling, can influence the pedestal density structure and overall pedestal performance.
- Open Access
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Design of a closed divertor with mid-leg pumping for core-edge integration in DIII-D
A new divertor has been designed for installation in the DIII-D tokamak with the goal of robustly achieving a detached outer divertor target while maintaining a hot plasma core. It does this by positioning a pumping duct part way up the separatrix leg in a tightly baffled divertor slot. This has the effect of allowing recycled neutral particles to accumulate near the target where they contribute to dissipative processes at low electron temperatures, while being removed before they can migrate further upstream to the main chamber and confined plasma. Simulations predict that this “chimney” design for the upper divertor enables detachment access at lower upstream plasma density, and passively stabilizes the detachment front near the location of the pump duct entrance. A summary of the engineering design, diagnostic and experimental plans is provided.
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDesign of a closed divertor with mid-leg pumping for core-edge integration in DIII-D
A new divertor has been designed for installation in the DIII-D tokamak with the goal of robustly achieving a detached outer divertor target while maintaining a hot plasma core. It does this by positioning a pumping duct part way up the separatrix leg in a tightly baffled divertor slot. This has the effect of allowing recycled neutral particles to accumulate near the target where they contribute to dissipative processes at low electron temperatures, while being removed before they can migrate further upstream to the main chamber and confined plasma. Simulations predict that this “chimney” design for the upper divertor enables detachment access at lower upstream plasma density, and passively stabilizes the detachment front near the location of the pump duct entrance. A summary of the engineering design, diagnostic and experimental plans is provided.
- Open Access
- 24 June 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (8) , 086051
Effect of outer divertor leg detachment on the high field side scrape-off layer in DIII-D and ASDEX Upgrade
In this work, evidence is presented that detachment of the outer divertor leg leads to a reduction of electron density and neutral pressure in the high-field side (HFS) scrape-off layer (SOL) of the ASDEX Upgrade (AUG) and DIII-D tokamaks with ion B×∇B drift directed toward the X-point (favorable configuration). These results are observed across multiple diagnostics and without the use of impurity seeding to reach detachment. In AUG, outer divertor leg detachment correlates with a decrease in electron density near the separatrix at the inner midplane, measured with HFS reflectometry. A concurrent reduction in inner divertor density and neutral pressure at the inner target is observed using divertor Thomson scattering and neutral pressure gauges. These effects are present in both L- and H-mode plasmas. In DIII-D, a similar reduction is detected through analysis of line-integrated hydrogenic emission measured by multiple diagnostics in the HFS SOL close to the separatrix. The consistent trends in both devices indicate that high electron density and strong hydrogenic emissivity in the HFS SOL are common features of high-density H-mode plasmas in the favorable configuration, independent of wall material and divertor geometry. In L-mode plasmas, the reduction in electron density and neutral pressure is not observed in DIII-D, possibly due to differences in wall material. These results emphasize the importance of the divertor state in determining the two-dimensional neutral distribution and edge fueling.
- 24 June 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (8) , 086051
Open AccessEffect of outer divertor leg detachment on the high field side scrape-off layer in DIII-D and ASDEX Upgrade
In this work, evidence is presented that detachment of the outer divertor leg leads to a reduction of electron density and neutral pressure in the high-field side (HFS) scrape-off layer (SOL) of the ASDEX Upgrade (AUG) and DIII-D tokamaks with ion B×∇B drift directed toward the X-point (favorable configuration). These results are observed across multiple diagnostics and without the use of impurity seeding to reach detachment. In AUG, outer divertor leg detachment correlates with a decrease in electron density near the separatrix at the inner midplane, measured with HFS reflectometry. A concurrent reduction in inner divertor density and neutral pressure at the inner target is observed using divertor Thomson scattering and neutral pressure gauges. These effects are present in both L- and H-mode plasmas. In DIII-D, a similar reduction is detected through analysis of line-integrated hydrogenic emission measured by multiple diagnostics in the HFS SOL close to the separatrix. The consistent trends in both devices indicate that high electron density and strong hydrogenic emissivity in the HFS SOL are common features of high-density H-mode plasmas in the favorable configuration, independent of wall material and divertor geometry. In L-mode plasmas, the reduction in electron density and neutral pressure is not observed in DIII-D, possibly due to differences in wall material. These results emphasize the importance of the divertor state in determining the two-dimensional neutral distribution and edge fueling.
- Open Access
- 14 January 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 46
Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D
- 14 January 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 46
Open AccessOverview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D
- Open Access
- 5 September 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 45
Recrystallization, cracking, and erosion of dispersoid-strengthened tungsten materials during exposure to divertor plasmas
- 5 September 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 45
Open AccessRecrystallization, cracking, and erosion of dispersoid-strengthened tungsten materials during exposure to divertor plasmas
- Open Access
- 7 March 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 43
Deuterium retention in pre-lithiated samples and Li–D co-deposits in the DIII-D tokamak
- 7 March 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 43
Open AccessDeuterium retention in pre-lithiated samples and Li–D co-deposits in the DIII-D tokamak
- Open Access
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Sandia National Laboratories Boundary Physics Research at DIII-D
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessSandia National Laboratories Boundary Physics Research at DIII-D