Chaitanya Kale
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chaitanya Kale has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Kiran N. Solanki
School for the Engineering of Matter, Transport, and Energy, Arizona State University, Tempe, AZ, USA
4 shared publications - M. Rajagopalan
School for Engineering of Matter, Transport, and Energy, Arizona State University, Tempe, USA
3 shared publications S. Turnage
School for the Engineering of Matter, Transport, and Energy, Arizona State University, Tempe, AZ, USA
3 shared publicationsB. Hornbuckle
U.S. Army Research Laboratory, APG, Adelphi, MD, USA
2 shared publicationsK. Darling
U.S. Army Research Laboratory, APG, Adelphi, MD, USA
2 shared publicationsS. N. Mathaudhu
Mechanical Engineering Department, University of California – Riverside, Riverside, CA, USA
2 shared publications
Latest Publications
- 14 February 2019
- Published by Springer Nature
- p. 199-200
Revealing the Role of Combined Loading on the Tension–Compression Asymmetry in a Textured AZ31 Magnesium Alloy
- 14 February 2019
- Published by Springer Nature
- p. 199-200
Revealing the Role of Combined Loading on the Tension–Compression Asymmetry in a Textured AZ31 Magnesium Alloy
- Open Access
- 12 July 2018
- Published by Springer Nature in Nature Communications
- Vol. 9 (1) , 1-10
Anomalous mechanical behavior of nanocrystalline binary alloys under extreme conditions
Fundamentally, material flow stress increases exponentially at deformation rates exceeding, typically, ~103 s−1, resulting in brittle failure. The origin of such behavior derives from the dislocation motion causing non-Arrhenius deformation at higher strain rates due to drag forces from phonon interactions. Here, we discover that this assumption is prevented from manifesting when microstructural length is stabilized at an extremely fine size (nanoscale regime). This divergent strain-rate-insensitive behavior is attributed to a unique microstructure that alters the average dislocation velocity, and distance traveled, preventing/delaying dislocation interaction with phonons until higher strain rates than observed in known systems; thus enabling constant flow-stress response even at extreme conditions. Previously, these extreme loading conditions were unattainable in nanocrystalline materials due to thermal and mechanical instability of their microstructures; thus, these anomalies have never been observed in any other material. Finally, the unique stability leads to high-temperature strength maintained up to 80% of the melting point (~1356 K).
- 12 July 2018
- Published by Springer Nature in Nature Communications
- Vol. 9 (1) , 1-10
Open AccessAnomalous mechanical behavior of nanocrystalline binary alloys under extreme conditions
Fundamentally, material flow stress increases exponentially at deformation rates exceeding, typically, ~103 s−1, resulting in brittle failure. The origin of such behavior derives from the dislocation motion causing non-Arrhenius deformation at higher strain rates due to drag forces from phonon interactions. Here, we discover that this assumption is prevented from manifesting when microstructural length is stabilized at an extremely fine size (nanoscale regime). This divergent strain-rate-insensitive behavior is attributed to a unique microstructure that alters the average dislocation velocity, and distance traveled, preventing/delaying dislocation interaction with phonons until higher strain rates than observed in known systems; thus enabling constant flow-stress response even at extreme conditions. Previously, these extreme loading conditions were unattainable in nanocrystalline materials due to thermal and mechanical instability of their microstructures; thus, these anomalies have never been observed in any other material. Finally, the unique stability leads to high-temperature strength maintained up to 80% of the melting point (~1356 K).
- 1 May 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 725, 503-509
Microstructure and dynamic strain aging behavior in oxide dispersion strengthened 91Fe-8Ni-1Zr (at%) alloy
- 1 May 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 725, 503-509
Microstructure and dynamic strain aging behavior in oxide dispersion strengthened 91Fe-8Ni-1Zr (at%) alloy
- Open Access
- 27 December 2017
- Published by Taylor & Francis in Materials Research Letters
- Vol. 6 (2) , 152-158
On the roles of stress-triaxiality and strain-rate on the deformation behavior of AZ31 magnesium alloys
The presence of complex states-of-stress and strain-rates directly influence the dominant deformation mechanisms operating in a given material under load. Mg alloys have shown limited ambient temperature formability due to the paucity of active slip-mechanisms, however, studies have focused on quasi-static strain-rates and/or simple loading conditions (primarily uniaxial or biaxial). For the first time, the influence of strain-rate and stress-triaxiality is utilized to unravel the active deformation mechanisms operating along the rolling, transverse- and normal-directions in wrought AZ31-alloy. It is discovered that the activation of various twin-mechanisms in the presence of multiaxial loading is governed by the energetics of the applied strain-rates. IMPACT STATEMENT It is shown for the first time that the higher deformation energy associated with dynamic strain-rates, coupled with high-triaxiality, promotes detwinning and texture evolution in HCP alloys with high c/a ratio. GRAPHICAL ABSTRACT
- 27 December 2017
- Published by Taylor & Francis in Materials Research Letters
- Vol. 6 (2) , 152-158
Open AccessOn the roles of stress-triaxiality and strain-rate on the deformation behavior of AZ31 magnesium alloys
The presence of complex states-of-stress and strain-rates directly influence the dominant deformation mechanisms operating in a given material under load. Mg alloys have shown limited ambient temperature formability due to the paucity of active slip-mechanisms, however, studies have focused on quasi-static strain-rates and/or simple loading conditions (primarily uniaxial or biaxial). For the first time, the influence of strain-rate and stress-triaxiality is utilized to unravel the active deformation mechanisms operating along the rolling, transverse- and normal-directions in wrought AZ31-alloy. It is discovered that the activation of various twin-mechanisms in the presence of multiaxial loading is governed by the energetics of the applied strain-rates. IMPACT STATEMENT It is shown for the first time that the higher deformation energy associated with dynamic strain-rates, coupled with high-triaxiality, promotes detwinning and texture evolution in HCP alloys with high c/a ratio. GRAPHICAL ABSTRACT
- 1 December 2017
- Published by Elsevier in Scripta Materialia
- Vol. 141, 36-40
Nanocrystalline material with anomalous modulus of resilience and springback effect
- 1 December 2017
- Published by Elsevier in Scripta Materialia
- Vol. 141, 36-40
Nanocrystalline material with anomalous modulus of resilience and springback effect
- 16 February 2017
- Published by Springer Nature
- p. 247-251
Dynamic Behavior of an AZ31 Alloy Under Varying Strain Rates and Stress Triaxialities
- 16 February 2017
- Published by Springer Nature
- p. 247-251
Dynamic Behavior of an AZ31 Alloy Under Varying Strain Rates and Stress Triaxialities