Sida Xing
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sida Xing has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
Svyatoslav Kharitonov
Ecole Polytechnique Fédérale de Lausanne (EPFL), Photonic Systems Laboratory, STI-IEL, Station 11, CH-1015, Lausanne, Switzerland
12 shared publicationsCamille-Sophie Brès
Ecole Polytechnique Fédérale de Lausanne (EPFL), Photonic Systems Laboratory, STI-IEL, Station 11, CH-1015, Lausanne, Switzerland
7 shared publications- Davide Grassani
Centre Suisse d’Electronique et de Microtechnique
7 shared publications Alexander J. Lind
Time and Frequency Division, NIST 1 , 325 Broadway, Boulder, Colorado 80305
5 shared publications- Scott A. Diddams
University of Colorado
5 shared publications Yanyan Zhang
Northwestern Polytechnical University, School of Artificial Intelligence, Optics and Electronics, Xi’an 710072, China
5 shared publications
Latest Publications
- Open Access
- 15 January 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13513, 66-391
Temporal measurement of high repetition rate frequency combs down to 3-optical-cycles
High repetition frequency near-infrared ultra-short lasers are crucial for efficient generation of low-noise mid-infrared frequency combs due to their broad in-phase spectrum and high peak power. In this paper, we present an improved structure of second harmonic generation-frequency resolved optical gating (SHG-FROG) for characterizing few-cycle pulses by retrieving their spectral power, temporal shape, and phase using a ptychographic reconstruction algorithm. We managed to characterize frequency combs with repetition rate from 100 MHz to 1 GHz; and measured pulses as short as sub-4 cycle pulses (< 20 fs) using this FROG.
- 15 January 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13513, 66-391
Open AccessTemporal measurement of high repetition rate frequency combs down to 3-optical-cycles
High repetition frequency near-infrared ultra-short lasers are crucial for efficient generation of low-noise mid-infrared frequency combs due to their broad in-phase spectrum and high peak power. In this paper, we present an improved structure of second harmonic generation-frequency resolved optical gating (SHG-FROG) for characterizing few-cycle pulses by retrieving their spectral power, temporal shape, and phase using a ptychographic reconstruction algorithm. We managed to characterize frequency combs with repetition rate from 100 MHz to 1 GHz; and measured pulses as short as sub-4 cycle pulses (< 20 fs) using this FROG.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS122_6
Mid-infrared frequency combs avoiding water windows
We demonstrate 3~5 µm and 8~12 µm frequency combs (5 mW) via intra-pulse difference-frequency generation, with 40 dB SNR carrier-envelope-offset frequency detection at 300 kHz RBW from residual single-cycle pump.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS122_6
Mid-infrared frequency combs avoiding water windows
We demonstrate 3~5 µm and 8~12 µm frequency combs (5 mW) via intra-pulse difference-frequency generation, with 40 dB SNR carrier-envelope-offset frequency detection at 300 kHz RBW from residual single-cycle pump.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS123_6
Towards the shot-noise limit of carrier-envelope-offset frequency retrieval
We showcase signal-to-noise ratio (SNR) maximization for carrier-envelope offset frequency (f0) in Er:fiber combs. With high supercontinuum coherence and small temporal walk-off, our homemade 200 MHz seed yields f0 with 62 dB SNR.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS123_6
Towards the shot-noise limit of carrier-envelope-offset frequency retrieval
We showcase signal-to-noise ratio (SNR) maximization for carrier-envelope offset frequency (f0) in Er:fiber combs. With high supercontinuum coherence and small temporal walk-off, our homemade 200 MHz seed yields f0 with 62 dB SNR.
- 6 September 2024
- Published by Optica Publishing Group in Photonics Research
- Vol. 12 (10) , 2115-2122
Two-octave frequency combs from an all-silica-fiber implementation
Mid-infrared frequency-comb spectroscopy enables measurement of molecules at megahertz spectral resolution, sub-hertz frequency accuracy, and microsecond acquisition speed. However, the widespread adoption of this technique has been hindered by the complexity and alignment sensitivity of mid-infrared frequency-comb sources. Leveraging the underexplored mid-infrared window of silica fibers presents a promising approach to address these challenges. In this study, we present the first, to the best of our knowledge, experimental demonstration and quantitative numerical description of mid-infrared frequency-comb generation in silica fibers. Our all-silica-fiber frequency comb spans over two octaves (0.8 μm to 3.4 μm) with a power output of 100 mW in the mid-infrared region. The amplified quantum noise is suppressed using four-cycle (25 fs) driving pulses, with the carrier-envelope offset frequency exhibiting a signal-to-noise ratio of 40 dB and a free-running bandwidth of 90 kHz. Our developed model provides quantitative guidelines for mid-infrared frequency-comb generation in silica fibers, enabling all-fiber frequency-comb spectroscopy in diverse fields such as organic synthesis, pharmacokinetics processes, and environmental monitoring.
- 6 September 2024
- Published by Optica Publishing Group in Photonics Research
- Vol. 12 (10) , 2115-2122
Two-octave frequency combs from an all-silica-fiber implementation
Mid-infrared frequency-comb spectroscopy enables measurement of molecules at megahertz spectral resolution, sub-hertz frequency accuracy, and microsecond acquisition speed. However, the widespread adoption of this technique has been hindered by the complexity and alignment sensitivity of mid-infrared frequency-comb sources. Leveraging the underexplored mid-infrared window of silica fibers presents a promising approach to address these challenges. In this study, we present the first, to the best of our knowledge, experimental demonstration and quantitative numerical description of mid-infrared frequency-comb generation in silica fibers. Our all-silica-fiber frequency comb spans over two octaves (0.8 μm to 3.4 μm) with a power output of 100 mW in the mid-infrared region. The amplified quantum noise is suppressed using four-cycle (25 fs) driving pulses, with the carrier-envelope offset frequency exhibiting a signal-to-noise ratio of 40 dB and a free-running bandwidth of 90 kHz. Our developed model provides quantitative guidelines for mid-infrared frequency-comb generation in silica fibers, enabling all-fiber frequency-comb spectroscopy in diverse fields such as organic synthesis, pharmacokinetics processes, and environmental monitoring.
- 18 January 2024
- Published by Optica Publishing Group in Optics Letters
- Vol. 49 (3) , 538-541
Broadband, high-power optical frequency combs covering visible to near-infrared spectral range
Optical frequency combs (OFCs) have become essential tools in a wide range of metrological and scientific research fields. However, in the reported literature, OFCs that cover the visible spectral range have a limited bandwidth and pulse energy. These drawbacks limit their potential applications, such as high-signal-to-noise ratio spectroscopic measurements. In this work, we demonstrate a broadband, high-power optical frequency comb covering the visible to near-infrared range (550 nm to 900 nm) with a high average power of approximately 300 mW. This is accomplished by the power scaling of optical pulses from a fully stabilized Er:fiber comb, coherent spectral broadening and finally the utilization of a PPLN’s χ(2) nonlinearity. The broadband, high-power, fully stabilized visible OFCs showcased in this work offer reliable laser sources for high-precision spectroscopic measurements, imaging, and comparisons of optical clocks.
- 18 January 2024
- Published by Optica Publishing Group in Optics Letters
- Vol. 49 (3) , 538-541
Broadband, high-power optical frequency combs covering visible to near-infrared spectral range
Optical frequency combs (OFCs) have become essential tools in a wide range of metrological and scientific research fields. However, in the reported literature, OFCs that cover the visible spectral range have a limited bandwidth and pulse energy. These drawbacks limit their potential applications, such as high-signal-to-noise ratio spectroscopic measurements. In this work, we demonstrate a broadband, high-power optical frequency comb covering the visible to near-infrared range (550 nm to 900 nm) with a high average power of approximately 300 mW. This is accomplished by the power scaling of optical pulses from a fully stabilized Er:fiber comb, coherent spectral broadening and finally the utilization of a PPLN’s χ(2) nonlinearity. The broadband, high-power, fully stabilized visible OFCs showcased in this work offer reliable laser sources for high-precision spectroscopic measurements, imaging, and comparisons of optical clocks.
- 1 January 2024
- Published by Optica Publishing Group
- p. ATh2A.5
1 GHz single-cycle frequency comb at 2 Watt
We demonstrate a 1 GHz frequency comb emitting 7.1 fs pulses at 1.8 W average power. The pulse center contains 57% energy, yielding 110 kW peak power. The retrieved carrier-envelope-offset frequency enables future comb stabilization.
- 1 January 2024
- Published by Optica Publishing Group
- p. ATh2A.5
1 GHz single-cycle frequency comb at 2 Watt
We demonstrate a 1 GHz frequency comb emitting 7.1 fs pulses at 1.8 W average power. The pulse center contains 57% energy, yielding 110 kW peak power. The retrieved carrier-envelope-offset frequency enables future comb stabilization.
- 1 January 2024
- Published by Optica Publishing Group
- p. SM3Q.4
All-silica fiber laser emitting two-octave frequency combs
We describe the conditions for generating multi-octave frequency combs in all-silica-fiber configuration. Experimental demonstration of a 200 MHz frequency comb covering 0.8 μm to 3.5 μm with a smooth mid-infrared part proved its validity.
- 1 January 2024
- Published by Optica Publishing Group
- p. SM3Q.4
All-silica fiber laser emitting two-octave frequency combs
We describe the conditions for generating multi-octave frequency combs in all-silica-fiber configuration. Experimental demonstration of a 200 MHz frequency comb covering 0.8 μm to 3.5 μm with a smooth mid-infrared part proved its validity.
- 24 November 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12935, 119-656
A polarization-maintaining mode-locked laser consuming 30mW of pump power: design and characterization
In order to bring frequency combs out of well-controlled laboratory environments, a robust mode-locked fiber laser is preferable with enhanced self-starting capability, and reduced size, weight, and power (SWaP). We try to reduce cavity loss as much as possible to lower the self-starting threshold and operation power. A lower concentration doped-fiber could restrain non-radiative transitions and scattering from color centers, which are two main loss sources of active fibers. We performed comparison experiments using two fibers with different rare-earth doping concentrations for better SWaP performance. Experimental results match with our predictions. Pumped by a 980nm semiconductor external-cavity stabilized diode laser, a mode-locking self-starts at about 60mW. The net-dispersion is managed by balancing the lengths of the positively dispersive Er-doped fiber with the negatively dispersive PM1550 fiber. It is worth noting that the passive mode-locking can be maintained with pump power as low as 30mW. The laser central wavelength is 1560nm and 3db bandwidth is about 42nm, corresponding to a transform-limited pulse duration of 61.43fs assuming sech2 pulse shape. The repetition frequency is 47.41MHz with more than 90dB signal-to-noise ration at 1KHz resolution bandwidth. At the minimum pump power, the laser output is at 4.2mW average power.
- 24 November 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12935, 119-656
A polarization-maintaining mode-locked laser consuming 30mW of pump power: design and characterization
In order to bring frequency combs out of well-controlled laboratory environments, a robust mode-locked fiber laser is preferable with enhanced self-starting capability, and reduced size, weight, and power (SWaP). We try to reduce cavity loss as much as possible to lower the self-starting threshold and operation power. A lower concentration doped-fiber could restrain non-radiative transitions and scattering from color centers, which are two main loss sources of active fibers. We performed comparison experiments using two fibers with different rare-earth doping concentrations for better SWaP performance. Experimental results match with our predictions. Pumped by a 980nm semiconductor external-cavity stabilized diode laser, a mode-locking self-starts at about 60mW. The net-dispersion is managed by balancing the lengths of the positively dispersive Er-doped fiber with the negatively dispersive PM1550 fiber. It is worth noting that the passive mode-locking can be maintained with pump power as low as 30mW. The laser central wavelength is 1560nm and 3db bandwidth is about 42nm, corresponding to a transform-limited pulse duration of 61.43fs assuming sech2 pulse shape. The repetition frequency is 47.41MHz with more than 90dB signal-to-noise ration at 1KHz resolution bandwidth. At the minimum pump power, the laser output is at 4.2mW average power.
- Open Access
POGD: Gradient Descent with New Stochastic Rules
There introduce Particle Optimized Gradient Descent (POGD), an algorithm based on the gradient descent but integrates the particle swarm optimization (PSO) principle to achieve the iteration. From the experiments, this algorithm has adaptive learning ability. The experiments in this paper mainly focus on the training speed to reach the target value and the ability to prevent the local minimum. The experiments in this paper are achieved by the convolutional neural network (CNN) image classification on the MNIST and cifar-10 datasets.
Open AccessPOGD: Gradient Descent with New Stochastic Rules
There introduce Particle Optimized Gradient Descent (POGD), an algorithm based on the gradient descent but integrates the particle swarm optimization (PSO) principle to achieve the iteration. From the experiments, this algorithm has adaptive learning ability. The experiments in this paper mainly focus on the training speed to reach the target value and the ability to prevent the local minimum. The experiments in this paper are achieved by the convolutional neural network (CNN) image classification on the MNIST and cifar-10 datasets.
- 1 January 2022
- Published by Optica Publishing Group
- Vol. 3, SF4O.4
1 GHz mid-infrared dual-comb spectrometer spanning more than 30 THz
We demonstrate a broadband 1 GHz mid-infrared dual comb spectrometer based on intra-pulse difference frequency generation, addressing the 3 – 5 µm wavelength region for the characterization of dynamic molecular systems.
- 1 January 2022
- Published by Optica Publishing Group
- Vol. 3, SF4O.4
1 GHz mid-infrared dual-comb spectrometer spanning more than 30 THz
We demonstrate a broadband 1 GHz mid-infrared dual comb spectrometer based on intra-pulse difference frequency generation, addressing the 3 – 5 µm wavelength region for the characterization of dynamic molecular systems.