Peter Grimm
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peter Grimm has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
Rakesh Chawla
Paul Scherrer Institute (PSI), Villigen CH-5232, Switzerland; École Polytechnique Fédérale de Lausanne, Lausanne CH-1015, Switzerland
6 shared publicationsF. Jatuff
Paul Scherrer Institute, Laboratory for Reactor Physics and Systems Behaviour CH-5232 Villigen-PSI, Switzerland
5 shared publicationsR. Chawla
Paul Scherrer Institute, Laboratory for Reactor Physics and Systems Behaviour CH-5232 Villigen-PSI, Switzerland
5 shared publicationsR. Seiler
Nuclear Energy and Safety Department, Paul Scherrer Institute, CH-5232 Villigen PSI, Switzerland
4 shared publicationsR. van Geemert
Nuclear Energy and Safety Department, Paul Scherrer Institute, CH-5232 Villigen PSI, Switzerland
4 shared publicationsA. Lüthi
Paul Scherrer Institut, CH-5232 Villigen PSI, Switzerland
3 shared publications
Latest Publications
- 1 November 2017
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 101, 280-287
Analysis of reactivity worths of burnt PWR fuel samples measured in LWR-PROTEUS Phase II using a CASMO-5 reflected-assembly model
- 1 November 2017
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 101, 280-287
Analysis of reactivity worths of burnt PWR fuel samples measured in LWR-PROTEUS Phase II using a CASMO-5 reflected-assembly model
- 1 November 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 97, 153-164
Validation of Monte Carlo based burnup codes against LWR-PROTEUS Phase-II experimental data
- 1 November 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 97, 153-164
Validation of Monte Carlo based burnup codes against LWR-PROTEUS Phase-II experimental data
- 1 August 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 94, 603-611
Nuclear data uncertainty propagation on spent fuel nuclide compositions
- 1 August 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 94, 603-611
Nuclear data uncertainty propagation on spent fuel nuclide compositions
- 13 December 2010
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (5) , 052909
Experimental Comparisons of 3D Reconstructed Pin-Power Distributions in Full-Scale BWR Fuel Assemblies
In this paper, reconstructed local fission rates obtained with the two-group nodal diffusion program PRESTO-2 , used at the Leibstadt Nuclear Power Plant (KKL) in Switzerland, are compared with experimental results and MCNPX calculations. The experimental facility consists of a test zone, where the measurements are made, surrounded by a buffer zone and two driver zones that render the system critical and also contain the control rods. The test zone consists of a tank that contains a array of BWR fuel assemblies of type . Four cases are considered, all corresponding to a 1.23 m high active zone moderated with light water at room temperature: (1) axially uniform enrichment and gadolinium content, (2) like case 1 but with an L-shaped control blade completely inserted, (3) enrichment and gadolinium content change at the core midplane, and (4) like case 2 but with the control blade partially inserted. The comparisons give insight into the accuracy of the pin-power reconstruction methodology. The axially uniform case without control blade shows a good radial agreement and a well predicted axial curvature of the flux. On the other hand, systematic deviations are observed in the radial direction for the controlled cases, with the axial heterogeneities causing deviations around the discontinuity and also in the axial curvature of the flux.- 13 December 2010
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (5) , 052909
Experimental Comparisons of 3D Reconstructed Pin-Power Distributions in Full-Scale BWR Fuel Assemblies
In this paper, reconstructed local fission rates obtained with the two-group nodal diffusion program PRESTO-2 , used at the Leibstadt Nuclear Power Plant (KKL) in Switzerland, are compared with experimental results and MCNPX calculations. The experimental facility consists of a test zone, where the measurements are made, surrounded by a buffer zone and two driver zones that render the system critical and also contain the control rods. The test zone consists of a tank that contains a array of BWR fuel assemblies of type . Four cases are considered, all corresponding to a 1.23 m high active zone moderated with light water at room temperature: (1) axially uniform enrichment and gadolinium content, (2) like case 1 but with an L-shaped control blade completely inserted, (3) enrichment and gadolinium content change at the core midplane, and (4) like case 2 but with the control blade partially inserted. The comparisons give insight into the accuracy of the pin-power reconstruction methodology. The axially uniform case without control blade shows a good radial agreement and a well predicted axial curvature of the flux. On the other hand, systematic deviations are observed in the radial direction for the controlled cases, with the axial heterogeneities causing deviations around the discontinuity and also in the axial curvature of the flux.- 1 December 2010
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 37 (12) , 1629-1639
Experimental validation of radial reconstructed pin-power distributions in full-scale BWR fuel assemblies with and without control blade
- 1 December 2010
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 37 (12) , 1629-1639
Experimental validation of radial reconstructed pin-power distributions in full-scale BWR fuel assemblies with and without control blade
- 1 January 2010
- Published by ASME International
- p. 227-236
Experimental Comparisons of 3D Reconstructed Pin-Power Distributions in Full-Scale BWR Fuel Assemblies
In this paper, reconstructed local fission rates obtained with the two-group nodal diffusion program PRESTO-2, used at the Leibstadt Nuclear Power Plant (KKL) in Switzerland, are compared with experimental results and MCNPX calculations. The experimental facility consists of a test zone, where the measurements are made, surrounded by a buffer zone and two driver zones that render the system critical and also contain the control rods. The test zone consists of a tank that contains a 3×3 array of BWR fuel assemblies of type SVEA-96+. Four cases are considered, all corresponding to a 1.23 m high active zone moderated with light water at room temperature: 1) axially uniform enrichment and gadolinium content, 2) like case 1 but with a L-shaped control blade completely inserted, 3) enrichment and gadolinium content change at the core mid-plane, 4) like case 2 but with the control blade partially inserted. The comparisons give insight into the accuracy of the pin power reconstruction methodology. The axially uniform case without control blade shows a good radial agreement and a well predicted axial curvature of the flux. On the other hand, systematic deviations are observed in the radial direction for the controlled cases, with the axial heterogeneities causing deviations around the discontinuity and also in the axial curvature of the flux.
- 1 January 2010
- Published by ASME International
- p. 227-236
Experimental Comparisons of 3D Reconstructed Pin-Power Distributions in Full-Scale BWR Fuel Assemblies
In this paper, reconstructed local fission rates obtained with the two-group nodal diffusion program PRESTO-2, used at the Leibstadt Nuclear Power Plant (KKL) in Switzerland, are compared with experimental results and MCNPX calculations. The experimental facility consists of a test zone, where the measurements are made, surrounded by a buffer zone and two driver zones that render the system critical and also contain the control rods. The test zone consists of a tank that contains a 3×3 array of BWR fuel assemblies of type SVEA-96+. Four cases are considered, all corresponding to a 1.23 m high active zone moderated with light water at room temperature: 1) axially uniform enrichment and gadolinium content, 2) like case 1 but with a L-shaped control blade completely inserted, 3) enrichment and gadolinium content change at the core mid-plane, 4) like case 2 but with the control blade partially inserted. The comparisons give insight into the accuracy of the pin power reconstruction methodology. The axially uniform case without control blade shows a good radial agreement and a well predicted axial curvature of the flux. On the other hand, systematic deviations are observed in the radial direction for the controlled cases, with the axial heterogeneities causing deviations around the discontinuity and also in the axial curvature of the flux.
- 1 January 2009
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 46 (9) , 933-943
Experimental Validation of Reaction Rate Distributions for a SVEA-96+ BWR Assembly with Hafnium Control Blades
The accurate estimation of reactor physics parameters related to the presence of cruciform absorber blades in boiling water reactors (BWRs) is important for safety assessment and for achieving flex...
- 1 January 2009
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 46 (9) , 933-943
Experimental Validation of Reaction Rate Distributions for a SVEA-96+ BWR Assembly with Hafnium Control Blades
The accurate estimation of reactor physics parameters related to the presence of cruciform absorber blades in boiling water reactors (BWRs) is important for safety assessment and for achieving flex...
- 1 January 2007
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 155 (1) , 96-101
Radial and Azimuthal 235U Fission and 238U Capture Distributions in BWR UO2 Pins: CASMO-4 and MCNP4C versus Activation Foil Measurements
- 1 January 2007
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 155 (1) , 96-101
Radial and Azimuthal 235U Fission and 238U Capture Distributions in BWR UO2 Pins: CASMO-4 and MCNP4C versus Activation Foil Measurements
- 1 January 2006
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 43 (3) , 223-230
Experimental Validation of Channel Bowing Effects on Pin Power Distributions in a Westinghouse SVEA-96+ Assembly
Effects of channel bowing on the pin power and 238U capture rate distributions have been studied experimentally and analytically in a test zone consisting of 9 full-size Westinghouse Atom SVEA-96+ fuel assemblies in the PROTEUS critical facility. A very significant bowing was simulated by displacing the central test assembly by ∽9 mm in the two horizontal directions from its centred position in the 3x3 assemblies array. Calculations were performed for a whole-reactor model using the HELIOS and BOXER codes and for a reflected assembly using CASMO-4. The agreement between calculated and measured reaction rate distributions in this configuration is found to be of a quality similar to that for the case with the central assembly in its nominal position. The direct comparison of measured and calculated effects of the central assembly displacement on the reaction rate distributions (based on the results obtained in the two different LWR-PROTEUS configurations) confirms that, for a well-characterized displacement, the codes are capable of predicting the changes with high accuracy.
- 1 January 2006
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 43 (3) , 223-230
Experimental Validation of Channel Bowing Effects on Pin Power Distributions in a Westinghouse SVEA-96+ Assembly
Effects of channel bowing on the pin power and 238U capture rate distributions have been studied experimentally and analytically in a test zone consisting of 9 full-size Westinghouse Atom SVEA-96+ fuel assemblies in the PROTEUS critical facility. A very significant bowing was simulated by displacing the central test assembly by ∽9 mm in the two horizontal directions from its centred position in the 3x3 assemblies array. Calculations were performed for a whole-reactor model using the HELIOS and BOXER codes and for a reflected assembly using CASMO-4. The agreement between calculated and measured reaction rate distributions in this configuration is found to be of a quality similar to that for the case with the central assembly in its nominal position. The direct comparison of measured and calculated effects of the central assembly displacement on the reaction rate distributions (based on the results obtained in the two different LWR-PROTEUS configurations) confirms that, for a well-characterized displacement, the codes are capable of predicting the changes with high accuracy.
- 31 May 2003
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 30 (8) , 911-930
Validation of axial pin power distributions in a 10×10 BWR assembly across an enrichment boundary under full-density water moderation conditions
- 31 May 2003
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 30 (8) , 911-930
Validation of axial pin power distributions in a 10×10 BWR assembly across an enrichment boundary under full-density water moderation conditions