Yashabanta N. Singhbabu
Research Subjects
Yashabanta N. Singhbabu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ranjan K. Sahu
Academic of Scientific and Innovative Research (AcSIR), New Delhi, India
3 shared publications A. K. Pramanick
CSIR-National Metallurgical Laboratory, Jamshedpur-831007, India
2 shared publicationsB. Sivakumar
2 shared publicationsD. Dadhich
2 shared publicationsRanjan K. Sahu
2 shared publicationsS. Das
2 shared publications
Latest Publications
- 3 June 2020
- Published by Wiley in Batteries & Supercaps
- Vol. 3 (10) , 1099-1111
Biowaste Orange Peel‐Derived Mesoporous Carbon as a Cost‐Effective Anode Material with Ultra‐Stable Cyclability for Potassium‐Ion Batteries
Potassium‐ion batteries (PIBs) are promising alternative to Lithium‐ion batteries (LIBs) owing to their economic merits. However, the PIBs have not met suitable anode materials comparable to graphite in LIBs. We synthesised an orange peel‐derived mesoporous carbon (OPDMC) as a potential anode material for high performance PIBs via facile one‐step carbonisation with self‐activation from waste orange peel. The OPDMC‐1000, which were carbonised at 1000 °C, exhibited impressive initial discharge/charge capacities of 408/224 mAh g−1 at 30 mA g−1 and retained the reversible capacity of 208.57 mAh g−1 over 100 cycles. Even after 2000 and 3000 cycles at specific currents of 200 and 500 mA g−1, it maintained the reversible capacities of 150.37 and 112 mAh g−1, respectively. A full cell employing the OPDMC exhibited an initial reversible discharge capacity of 185.32 mAh g−1 at 50 mA g−1 with capacity retention of 71.60 % after 50 cycles, indicating its practical applicability.
- 3 June 2020
- Published by Wiley in Batteries & Supercaps
- Vol. 3 (10) , 1099-1111
Biowaste Orange Peel‐Derived Mesoporous Carbon as a Cost‐Effective Anode Material with Ultra‐Stable Cyclability for Potassium‐Ion Batteries
Potassium‐ion batteries (PIBs) are promising alternative to Lithium‐ion batteries (LIBs) owing to their economic merits. However, the PIBs have not met suitable anode materials comparable to graphite in LIBs. We synthesised an orange peel‐derived mesoporous carbon (OPDMC) as a potential anode material for high performance PIBs via facile one‐step carbonisation with self‐activation from waste orange peel. The OPDMC‐1000, which were carbonised at 1000 °C, exhibited impressive initial discharge/charge capacities of 408/224 mAh g−1 at 30 mA g−1 and retained the reversible capacity of 208.57 mAh g−1 over 100 cycles. Even after 2000 and 3000 cycles at specific currents of 200 and 500 mA g−1, it maintained the reversible capacities of 150.37 and 112 mAh g−1, respectively. A full cell employing the OPDMC exhibited an initial reversible discharge capacity of 185.32 mAh g−1 at 50 mA g−1 with capacity retention of 71.60 % after 50 cycles, indicating its practical applicability.
- 1 September 2018
- Published by Elsevier in Surface and Coatings Technology
- Vol. 349, 119-132
Corrosion-protective reduced graphene oxide coated cold rolled steel prepared using industrial setup: A study of protocol feasibility for commercial production
- 1 September 2018
- Published by Elsevier in Surface and Coatings Technology
- Vol. 349, 119-132
Corrosion-protective reduced graphene oxide coated cold rolled steel prepared using industrial setup: A study of protocol feasibility for commercial production
- 26 March 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (17) , 8035-8047
Efficient anti-corrosive coating of cold-rolled steel in a seawater environment using an oil-based graphene oxide ink
We report the production of an efficient anti-corrosive coating of cold-rolled (CR) steel in a seawater environment (∼3.5 wt% NaCl aqueous solution) using an oil-based graphene oxide ink. The graphene oxide was produced by heating Aeschynomene aspera plant as a carbon source at 1600 °C in an argon atmosphere. The ink was prepared by cup-milling the mixture of graphene oxide and sunflower oil for 10 min. The coating of ink on the CR steel was made using the dip-coating method, followed by curing at 350 °C for 10 min in air atmosphere. The results of the potentiodynamic polarization show that the corrosion rate of bare CR steel decreases nearly 10 000-fold by the ink coating. Furthermore, the salt spray test results show that the red rusting in the ink-coated CR steel is initiated after 100 h, in contrast to 24 h and 6 h in the case of oil-coated and bare CR steel, respectively. The significant decrease in the corrosion rate by the ink-coating is discussed based on the impermeability of graphene oxide to the corrosive ions.
- 26 March 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (17) , 8035-8047
Efficient anti-corrosive coating of cold-rolled steel in a seawater environment using an oil-based graphene oxide ink
We report the production of an efficient anti-corrosive coating of cold-rolled (CR) steel in a seawater environment (∼3.5 wt% NaCl aqueous solution) using an oil-based graphene oxide ink. The graphene oxide was produced by heating Aeschynomene aspera plant as a carbon source at 1600 °C in an argon atmosphere. The ink was prepared by cup-milling the mixture of graphene oxide and sunflower oil for 10 min. The coating of ink on the CR steel was made using the dip-coating method, followed by curing at 350 °C for 10 min in air atmosphere. The results of the potentiodynamic polarization show that the corrosion rate of bare CR steel decreases nearly 10 000-fold by the ink coating. Furthermore, the salt spray test results show that the red rusting in the ink-coated CR steel is initiated after 100 h, in contrast to 24 h and 6 h in the case of oil-coated and bare CR steel, respectively. The significant decrease in the corrosion rate by the ink-coating is discussed based on the impermeability of graphene oxide to the corrosive ions.
- 3 March 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (15) , 6510-6519
Observation of large positive magneto-resistance in bubble decorated graphene oxide films derived from shellac biopolymer: a new carbon source and facile method for morphology-controlled properties
We report a large positive magneto-resistance (MR) in bubble decorated graphene oxide films that are derived from shellac biopolymer as a carbon source. These films were produced on a quartz substrate by heating the biopolymer coated substrate at 900 °C in an argon atmosphere. The characterization data of the films using Raman, X-ray photoelectron spectroscopy, field emission scanning electron microscopy and transmission electron microscopy reveal that shellac can be used as a new carbon source to produce transparent bubble decorated graphene oxide films. The magneto-resistance results show a 130% change in the resistance of the films at 3 K under a perpendicular magnetic field of 15 T, and the value decreases exponentially up to 50 K. The observed MR properties of the bubble decorated graphene oxide films are explained using a weak anti-localization and quantum interference model in the low magnetic field region, while the Lorentz force accounts for the MR properties well in the high magnetic field region.
- 3 March 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (15) , 6510-6519
Observation of large positive magneto-resistance in bubble decorated graphene oxide films derived from shellac biopolymer: a new carbon source and facile method for morphology-controlled properties
We report a large positive magneto-resistance (MR) in bubble decorated graphene oxide films that are derived from shellac biopolymer as a carbon source. These films were produced on a quartz substrate by heating the biopolymer coated substrate at 900 °C in an argon atmosphere. The characterization data of the films using Raman, X-ray photoelectron spectroscopy, field emission scanning electron microscopy and transmission electron microscopy reveal that shellac can be used as a new carbon source to produce transparent bubble decorated graphene oxide films. The magneto-resistance results show a 130% change in the resistance of the films at 3 K under a perpendicular magnetic field of 15 T, and the value decreases exponentially up to 50 K. The observed MR properties of the bubble decorated graphene oxide films are explained using a weak anti-localization and quantum interference model in the low magnetic field region, while the Lorentz force accounts for the MR properties well in the high magnetic field region.
- 1 July 2013
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 564, 78-83
Degradation of Congo red pollutants using microwave derived SrFe12O19: An efficient magnetic photocatalyst under visible light
- 1 July 2013
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 564, 78-83
Degradation of Congo red pollutants using microwave derived SrFe12O19: An efficient magnetic photocatalyst under visible light
- 26 November 2012
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 1 (5) , 958-966
Capsule-embedded reduced graphene oxide: synthesis, mechanism and electrical properties
We report the synthesis of capsule-embedded reduced graphene oxide (rGO) by photocatalytic reduction in the presence of peanut shaped α-Fe2O3 particles under visible light. This process is able to produce highly stabilized water dispersible rGO without the help of a stabilizer, which is suitable to make thin films on a glass substrate by the drop casting method. In addition, the evolution of the morphology with different visible light exposure times ranging from 5 to 120 minutes reveals that the catalyst leads to transformation of a few rGO sheets into capsules via a core–shell structure. These capsules are stable on the rGO sheet at a vacuum of 10−9 Torr, but unstable under vacuum annealing at 400 °C and 10−5 Torr that created impressions on the rGO film. The bandgap of the capsule-embedded rGO decreases non-linearly with the visible light exposure time; from 2.47 eV at 5 min to 1.73 eV at 120 min. The vacuum annealed rGO films on glass substrates show an electrical conductivity of 2000 S m−1 at 300 K and the conduction is dominated by two-dimensional variable range hopping. The formation of capsules is described based on electrostatic interactions in association with the dipole force of the monodispersed peanut shaped α-Fe2O3 particles, whereas, the bandgap opening and high conductivity are attributed to the residual oxygen functional groups such as carbonyl (>CO) and epoxy (C–O–C) on the rGO, in addition to the modulated surface morphology.
- 26 November 2012
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 1 (5) , 958-966
Capsule-embedded reduced graphene oxide: synthesis, mechanism and electrical properties
We report the synthesis of capsule-embedded reduced graphene oxide (rGO) by photocatalytic reduction in the presence of peanut shaped α-Fe2O3 particles under visible light. This process is able to produce highly stabilized water dispersible rGO without the help of a stabilizer, which is suitable to make thin films on a glass substrate by the drop casting method. In addition, the evolution of the morphology with different visible light exposure times ranging from 5 to 120 minutes reveals that the catalyst leads to transformation of a few rGO sheets into capsules via a core–shell structure. These capsules are stable on the rGO sheet at a vacuum of 10−9 Torr, but unstable under vacuum annealing at 400 °C and 10−5 Torr that created impressions on the rGO film. The bandgap of the capsule-embedded rGO decreases non-linearly with the visible light exposure time; from 2.47 eV at 5 min to 1.73 eV at 120 min. The vacuum annealed rGO films on glass substrates show an electrical conductivity of 2000 S m−1 at 300 K and the conduction is dominated by two-dimensional variable range hopping. The formation of capsules is described based on electrostatic interactions in association with the dipole force of the monodispersed peanut shaped α-Fe2O3 particles, whereas, the bandgap opening and high conductivity are attributed to the residual oxygen functional groups such as carbonyl (>CO) and epoxy (C–O–C) on the rGO, in addition to the modulated surface morphology.