YHYasir Arafat Hutapea

Yasir Arafat Hutapea

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yasir Arafat Hutapea has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Highly Durable PtNiCo Beads-On-Nanowires with Pt-Skin Surface for Oxygen Reduction Reaction in Acidic Media

    by Yu Zhuang, Bohao Du, Masaru Kato, Yasir Arafat Hutapea, Akari Hayashi, Yuta Kato, Takahito Hoshi, Shinji Tanioku, Ichizo Yagi

  • Open Access

    Improved chemical durability in polymer electrolyte membranes with nanocellulose-based gas barrier interlayers

    by I Yang, Zulfi Al Rasyid Gautama, Yasir Arafat Hutapea, Miho Ariyoshi, Shigenori Fujikawa, Takeharu Sugiyama, Stephen Matthew Lyth, Kazunari Sasaki, Masamichi Nishihara


  • Reduction of oxygen transport resistance in PEFC cathode through blending a high oxygen permeable polymer

    by Yasir Arafat Hutapea, Masamichi Nishihara, Zulfi Al Rasyid Gautama, Albert Mufundirwa, Stephen Matthew Lyth, Takeharu Sugiyama, Mayumi Nagayama, Kazunari Sasaki, Akari Hayashi


  • Open Access

    The Effect of Chemical Activation Using Base Solution With Various Concentrations Towards Sarulla Natural Zeolite

    by Saharman Gea, Agus Haryono, Andriayani Andriayani, Junifa Layla Sihombing, Ahmad Nasir Pulungan, Tiamina Nasution, Rahayu Rahayu, Yasir Arafat Hutapea

    Abstract : Material characteristics analysis of Sarulla natural zeolite (SNZ) with base activation has been carried out. The base used was NaOH at various concentrations; 0.2 M, 0.5 M, and 2 M. Base activated catalysts were characterized by X-ray Fluorescence (XRF), X-ray diffractometer (XRD), Fourier-transform Infrared (FTIR) Spectroscopy, Scanning Electron Microscopy (SEM) and gas adsorption analysis using BET method. The procedures applied have caused differences in adsorption and desorption rates as well as the crystallinity values of the catalytic materials. Moreover, the ratio of Si/Al contents has also changed at the lowest concentration. On the other hand, the crystallinity of catalysts has decreased at the highest concentration of base applied. The results are reinforced in FTIR characterization which shows the changes of silanol bonds to become silicate and aluminate. Furthermore, morphological analysis of the catalysts shows that homogenous surface was obtained at low concentration, while rough/lumpy surfaces was obtained at higher concentration. Abstrak : Analisis terhadap karakteristik material dari zeolit alam Sarulla (SNZ) dengan metode aktivasi basa telah dilakukan. Basa yang digunakan ialah NaOH dengan berbagai konsentrasi; 0,2 M; 0,5 M, dan 2 M. Katalis yang telah diaktivasi dengan basa kemudian dikarakterisasi dengan Analisis X-ray Fluorescence (XRF), X-ray diffractometer (XRD), Fourier-transform Infrared (FTIR) Spectroscopy, Scanning Electron Microscopy (SEM) dan Gas Adsorption menggunakan metode BET. Dari hasil penelitian, ditemukan perbedaan pada tingkat adsorpsi dan desorpsi, begitu juga dengan kristalinitas pada material katalis. Lebih jauh, rasio konten Si/Al juga berubah pada basa dengan konsentrasi terendah. Di sisi lain, tingkat kristalinitas dari katalis mengalami penurunan pada basa dengan konsentrasi tertinggi. Hasil ini diperkuat dengan data FTIR yang menunjukkan perubahan ikatan silanol menjadi silikat dan aluminat. Lebih jauh, analisis morfologi pada katalis menunjukkan bahwa permukaan yang homogen didapatkan dari penggunaan basa dengan konsentrasi rendah. Sebaliknya, basa dengan konsentrasi tinggi memberikan bentuk permukaan katalis yang tidak homogen serta kasar.


  • Open Access

    The Stabilization of Liquid Smoke through Hydrodeoxygenation Over Nickel Catalyst Loaded on Sarulla Natural Zeolite

    by Saharman Gea, Agus Haryono, Andriayani Andriayani, Junifa Layla Sihombing, Ahmad Nasir Pulungan, Tiamina Nasution, Rahayu Rahayu, Yasir Arafat Hutapea

    Constituents of liquid smoke possess a huge potential to be converted as value-added chemicals, such as flavoring, antiseptics, antioxidants, or even fossil oil substitutes. However, liquid smoke instability, led by the presence of oxygenate compounds, is an obstacle for further utilization and processing. On the other hand, catalyst efficiency in hydrodeoxygenation (HDO) remains challenging. Sarulla natural zeolite (Z), with abundant availability, has not been comprehensively investigated in the catalytic performance of HDO. In this study, Sarulla natural zeolite with different Si/Al ratios, which are activated by several concentrations of hydrochloric acid and nickel supported by Z (Ni-Z) synthesized by wet impregnation, were evaluated for HDO of liquid smoke, particularly in reducing oxygenate compounds. Catalyst morphology, surface area, pores, and crystallinity are investigated. Catalytic performances were evaluated, particularly on reducing oxygenate compounds and the shifting of phenol and its derivatives. Furthermore, the liquid smoke product of HDO was analyzed by gas chromatography-mass spectrometry (GC-MS). The data obtained reveal that the HDO process of liquid smoke with the Z3 catalyst shows the best activity compared to Z5 and Z7, with phenol conversion of 62.39% and 11.93% of alkoxy reduction. Meanwhile, the best Ni metal catalyst system activity was given by the Ni-Z5 catalyst compared to Ni-Z3 and Ni-Z7, where phenol conversion and alkoxy reduction were at 60.06% and 11.49%, respectively.


  • Improving Quality and Yield Production of Coconut Shell Charcoal Through a Modified Pyrolysis Reactor with Tar Scrubber to Reduce Smoke Pollution

    by Reka Mustika Sari, Saharman Gea, Basuki Wirjosentono, Sunit Hendrana, Yasir Arafat Hutapea

    The two main problems faced by the conventional coconut shell charcoal industry are low charcoal yield and smoke pollution. Therefore, the purpose of this study is to modify the pyrolysis reactor equipped with tar scrubbers as a solution to the problem of smoke pollution and yield, and improve the quality of charcoal. A reactor of the size 2.4 x 1.2 x 1.2 m and the heat coming out of the rocket stove can be blown from the bottom, thus it can propagate evenly through a perforated plate. The reactor was designed with circulating pipes as places for channeling non-condensable gases to be used as fuel. Produced charcoal yield rose from 23% to 28% and the quality of charcoal fulfilled SNI requirements and those of the Republic of Indonesia Ministry of Energy and Mineral Resources. The morphology of charcoal and mineral composition in SEM-EDX showed an increase in the composition of carbon elements by 83.63%. The FTIR spectrum results decrease in the broad intensity of O-H and the charcoal structure produced was amorphous. The total pore volume was 0.07336 cc/g and the pore surface area was 12.716 m2/g. This modified reactor with tar scrubber produces better yield, and minimal smoke pollution compared to traditional combustion of charcoal.


  • Open Access

    Characteristic and Catalytic Performance of Co and Co-Mo Metal Impregnated in Sarulla Natural Zeolite Catalyst for Hydrocracking of MEFA Rubber Seed Oil into Biogasoline Fraction

    by Junifa Layla Sihombing, Saharman Gea, Basuki Wirjosentono, Harry Agusnar, Ahmad Nasir Pulungan, Herlinawati Herlinawati, Muhammad Yusuf, Yasir Arafat Hutapea

    This research was aimed to investigate the effect of Co and Co-Mo metal loaded on Sarulla Natural Zeolite which has been activated and calcined (SNZ-Cal) as supports for better understanding of characterization and catalytic activity on hydrocracking of MEFA rubber seed oil. The Co and Co-Mo metal was added through a wet impregnation method using Co(NO3)2·6H2O and (NH4)·6Mo7O24·4H2O precursor salts. The catalyst was oxidized at 500 °C for 2 h within oxygen gas flow, followed by a reduction process with H2 gas flow with similar condition to obtain the catalysts. Based on the result, it was found that the resulted catalysts displayed an increase in crystal grain size compared to the metal-free catalyst. Particularly, catalyst that was impregnated with Co metal has a larger surface area and pore diameter and smaller pore volume than Co-Mo metal impregnated to the catalyst. In fact, it was revealed that this catalyst possessed the highest catalytic activity and selectivity. Furthermore, the resulting gas products reached 64 wt.% and the distribution of biogasoline fraction of hydrocarbons (C6-C12) amounted to 83.19 wt.%.


  • Enhancing the quality of nata de coco starter by channeling the oxygen into the bioreactor through agitation method

    by Saharman Gea, Khatarina Meldawati Pasaribu, Kerista Sebayang, Elisa Julianti, Suci Aisyah Amaturahim, Siti Utari Rahayu, Yasir Arafat Hutapea

    The provision of a proper quality starter to produce nata de coco through agitation method has been done. The main concern of this method was its effect after the oxygen flow into the bioreactor containing glucose-based medium which was inoculated by Acetobacterxylinum. The 10-liter bioreactor was operated with a stirring speed of 200 rpm at room temperature. After 10 days, the broth within the bioreactor was harvested and analyzed by using an optical microscope, and the results were compared with an oxygen-free broth. Based on the observation of bacterial clusters placed on the watch glass, the oxygenated broth was discovered to remain compact with each other. In contrast, the oxygen-free broth of the bacterial cluster was found to be cloistered. When the bacterial cluster was used to inoculate the media, the 15-day observation performed different results.


  • The analysis of thermal and mechanical properties of biocomposite policaprolactone/cellulose nanofiber from oil palm empty fruit bunches

    by Saharman Gea, Monti Surga, Sri Rahayu, Marpongahtun, Yasir Arafat Hutapea, Averroes Fazlurrahman Piliang

    Oil Palm Empty Fruit Bunches (OPEFB) are abundant organic waste that contains cellulosic compound. This study aims to fabricate PCL/cellulose nanofiber bionanocomposites from OPEFB and to analyze their thermal and mechanical properties. Nanofiber cellulose with an average size of 32 nm was isolated from OPEFB by using alkaline condition and mechanicalmethods. This was proven by the presence of functional group analysed from the FT-IR spectrum and morphological analysis with TEM. Bio-nanocompositePCL/cellulose nanofiberfrom OPEFBwas further made in several variations, namely: 100%: 0%, 90%: 10%, 80%: 20%, 70%: 30%, 60%: 40%. The samples were then tested for their mechanical properties with tensile test to determine optimal results and the optimal ratio was 80%: 20% w/v, with tensile strength of about 8,830 Mpa and 40,78% strain. This is also proven by morphological analysis using SEM which shows a flat and homogeneous surface. The optimal sample was thermally analyzed using DSC and it is showed that the resulting bionanocomposite decomposed (Td) at 513.10°C through an exothermic process with a heat of 414.08 J/g.


  • Study of bacterial cellulose as scaffold on cartilage tissue engineering

    by Saharman Gea, Reka Mustika Sari, Averroes Fazlurrahman Piliang, Denny Pratama Indrawan, Yasir Arafat Hutapea

    Preparation of scaffold from bacterial cellulose has been carried out. Chondrocyte cells have been placed on Bacterial Cellulose (BC) sterilization and then given with DMEM growth medium with 20% of FES. Growing cells were masured using a haemocytometer and also identified the dead cells with the aid of fixation. Apparently, it was found that cell growth measured at 1 mL cell is 2.44x105 cells/ mL within 9 days.