Václav Sebera
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Václav Sebera has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Jan Tippner
Department of Wood Science and Technology, Faculty of Forestry and Wood Technology, Mendel University in Brno, Brno, Czech Republic
17 shared publications Jaromír Milch
Department of Wood Science, Faculty of Forestry and Wood Technology , Mendel University in Brno , Zemědělská 3 , 613 00 Brno , Czech Republic
7 shared publicationsJiří Kunecký
7 shared publications- Martin Brabec
Mendel University in Brno
7 shared publications Hana Hasníková
5 shared publicationsMichal Kloiber
5 shared publications
Latest Publications
- 1 January 2026
- Published by BioResources in BioResources
- Vol. 21 (2)
Detection of defects in glue bonding of cross-laminated timber using experimental and numerical modal analysis
The preferred structural elements for taller timber buildings include cross-laminated timber (CLT), the performance of which significantly depends on the adhesive bond (AB) quality that may be influenced by manufacturing or factors within the service life. Both may contribute to a delamination, which represents a serious structural damage of the CLT. The study utilised both experimental and numerical modal analyses to assess the influence of damaged AB on CLT vibrational behavior. Both approaches confirmed that the CLT stiffness and eigenfrequencies decreased with AB damage, and both found agreement on certain modal shapes. FEA showed ideal patterns also in terms of localization of the damaged AB using modal shape damage index. Meanwhile, experiments showed its limits due to natural variability of wood, CLT, and measurement setup. The obtained results show a potential for in situ grading and inspection. However, the effect of variability of material properties of CLT should be studied further.
- 1 January 2026
- Published by BioResources in BioResources
- Vol. 21 (2)
Detection of defects in glue bonding of cross-laminated timber using experimental and numerical modal analysis
The preferred structural elements for taller timber buildings include cross-laminated timber (CLT), the performance of which significantly depends on the adhesive bond (AB) quality that may be influenced by manufacturing or factors within the service life. Both may contribute to a delamination, which represents a serious structural damage of the CLT. The study utilised both experimental and numerical modal analyses to assess the influence of damaged AB on CLT vibrational behavior. Both approaches confirmed that the CLT stiffness and eigenfrequencies decreased with AB damage, and both found agreement on certain modal shapes. FEA showed ideal patterns also in terms of localization of the damaged AB using modal shape damage index. Meanwhile, experiments showed its limits due to natural variability of wood, CLT, and measurement setup. The obtained results show a potential for in situ grading and inspection. However, the effect of variability of material properties of CLT should be studied further.
- 25 September 2025
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 21 (5) , 1-13
Towards a strain-based approach to mode I fracture characterization in Norway spruce considering three anatomical directions
- 25 September 2025
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 21 (5) , 1-13
Towards a strain-based approach to mode I fracture characterization in Norway spruce considering three anatomical directions
- 3 September 2024
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 310
Optimization of CZM parameters of Norway spruce tested in mode I using multistart simplex method
- 3 September 2024
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 310
Optimization of CZM parameters of Norway spruce tested in mode I using multistart simplex method
- Open Access
- 7 November 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (4) , 1349-1359
Mode I fracture of beech-adhesive bondline at three different temperatures
Single edge-notched three-point bending tests (SEN-TPB) for mode I were utilized to experimentally evaluate fracture properties of adhesive bondlines in European beech (Fagus Sylvatica L.). The bondline was examined at two anatomical planes with TR and RT orientation and at control and two elevated temperatures (70°C and 140°C). Among epoxy (EPI), melamine-urea formaldehyde (MUF), and polyurethane (PUR) adhesives, the highest average critical energy Gc with 0.80 N/mm and fracture energy Gf with 1079.4 N/mm were obtained for EPI in the TR plane and under standard climate conditions (20°C/65% relative humidity), followed by MUF (Gc = 0.50 N/mm and Gf = 620 N/mm) and PUR (Gc = 0.25 N/mm and Gf = 290.9 N/mm), respectively. PUR was least effected by elevated temperature, and no significant differences for Gc and Gf between TR and RT bondline orientations were found for MUF and PUR treated at 20°C/65% relative humidity while comparisons between other factors varied significantly. Treatment of specimens at elevated temperatures resulted in reduced fracture performance regardless of wood grain orientation or the adhesive system.
- 7 November 2022
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 18 (4) , 1349-1359
Open AccessMode I fracture of beech-adhesive bondline at three different temperatures
Single edge-notched three-point bending tests (SEN-TPB) for mode I were utilized to experimentally evaluate fracture properties of adhesive bondlines in European beech (Fagus Sylvatica L.). The bondline was examined at two anatomical planes with TR and RT orientation and at control and two elevated temperatures (70°C and 140°C). Among epoxy (EPI), melamine-urea formaldehyde (MUF), and polyurethane (PUR) adhesives, the highest average critical energy Gc with 0.80 N/mm and fracture energy Gf with 1079.4 N/mm were obtained for EPI in the TR plane and under standard climate conditions (20°C/65% relative humidity), followed by MUF (Gc = 0.50 N/mm and Gf = 620 N/mm) and PUR (Gc = 0.25 N/mm and Gf = 290.9 N/mm), respectively. PUR was least effected by elevated temperature, and no significant differences for Gc and Gf between TR and RT bondline orientations were found for MUF and PUR treated at 20°C/65% relative humidity while comparisons between other factors varied significantly. Treatment of specimens at elevated temperatures resulted in reduced fracture performance regardless of wood grain orientation or the adhesive system.
- Open Access
Selected Properties of Veneered Lightweight Particleboards with Expanded Polystyrene
The aim of this study was to improve the properties of lightweight particleboards by their veneering. The industrially produced wood particles, rotary-cut birch veneer, expanded polystyrene (EPS) granules and urea-formaldehyde (UF) resin were used to manufacture non-veneered and veneered boards in laboratory conditions. The boards were manufactured with different densities of 350, 450 and 550 kg/m3 and with various levels of EPS content 4, 7 and 10%. Boards without EPS granules as the reference were also manufactured. Bending strength (MOR), modulus of elasticity in bending (MOE), internal bond (IB) strength, thickness swelling (TS) and water absorption (WA) of lightweight particleboards were determined. This study confirmed that veneering of lightweight particleboards by birch veneer improved mechanical properties significantly. The MOR and MOE of veneered boards throughout the whole density range of 350–550 kg/m3 meet the requirements of the CEN/TS 16368 for lightweight particleboards types LP1 and LP2. The IB strength of veneered boards only with density of 550 kg/m3 meets the requirements of CEN/TS 16368 (type LP1). The MOR, MOE and IB of non-veneered boards also meet the requirements of CEN/TS 16368 (type LP1) except boards with density of 350 kg/m3 for MOR and MOE, and except densities of 350 and 450 kg/m3 for IB.
Open AccessSelected Properties of Veneered Lightweight Particleboards with Expanded Polystyrene
The aim of this study was to improve the properties of lightweight particleboards by their veneering. The industrially produced wood particles, rotary-cut birch veneer, expanded polystyrene (EPS) granules and urea-formaldehyde (UF) resin were used to manufacture non-veneered and veneered boards in laboratory conditions. The boards were manufactured with different densities of 350, 450 and 550 kg/m3 and with various levels of EPS content 4, 7 and 10%. Boards without EPS granules as the reference were also manufactured. Bending strength (MOR), modulus of elasticity in bending (MOE), internal bond (IB) strength, thickness swelling (TS) and water absorption (WA) of lightweight particleboards were determined. This study confirmed that veneering of lightweight particleboards by birch veneer improved mechanical properties significantly. The MOR and MOE of veneered boards throughout the whole density range of 350–550 kg/m3 meet the requirements of the CEN/TS 16368 for lightweight particleboards types LP1 and LP2. The IB strength of veneered boards only with density of 550 kg/m3 meets the requirements of CEN/TS 16368 (type LP1). The MOR, MOE and IB of non-veneered boards also meet the requirements of CEN/TS 16368 (type LP1) except boards with density of 350 kg/m3 for MOR and MOE, and except densities of 350 and 450 kg/m3 for IB.
- Open Access
Effects of Wood Particles from Deadwood on the Properties and Formaldehyde Emission of Particleboards
The volume of deadwood increases annually because of changes in environmental, climatic, and hydrological conditions. On the other hand, during the last decade, manufacturers of wood-based boards have been facing an acute problem of a shortage of conventional raw materials. The purpose of this study was to evaluate the possibility of using wood particles from deadwood in the production of particleboards. Three-layer particleboards with different content of deadwood particles (0%, 25%, 50%, 75%, 100%) were produced. Conventional urea-formaldehyde (UF) resin was used for gluing the particles. The physical and mechanical properties of the boards, as well as the formaldehyde content in the boards, were determined. In addition, the effect of adding melamine-urea-formaldehyde (MUF) resin to UF adhesive on the properties of the boards was investigated. Replacing conventional sound wood particles with deadwood particles leads to deterioration of the physical and mechanical properties of the boards. The boards from deadwood particles absorb more water and swell more. The bending strength (MOR), modulus of elasticity in bending (MOE), and internal bonding (IB) values for boards with 100% deadwood particles are reduced by 26.5%, 23.1%, and 72.4%, respectively, compared to reference boards from sound wood particles. Despite this, a significant advantage is that boards made from 100% deadwood particles are characterized by 34.5% less formaldehyde content than reference boards made from conventional sound wood. Moreover, adding 3% of MUF resin to UF adhesive increases MOR, MOE, and IB by 44.1%, 43.3%, and 294.4%, respectively.
Open AccessEffects of Wood Particles from Deadwood on the Properties and Formaldehyde Emission of Particleboards
The volume of deadwood increases annually because of changes in environmental, climatic, and hydrological conditions. On the other hand, during the last decade, manufacturers of wood-based boards have been facing an acute problem of a shortage of conventional raw materials. The purpose of this study was to evaluate the possibility of using wood particles from deadwood in the production of particleboards. Three-layer particleboards with different content of deadwood particles (0%, 25%, 50%, 75%, 100%) were produced. Conventional urea-formaldehyde (UF) resin was used for gluing the particles. The physical and mechanical properties of the boards, as well as the formaldehyde content in the boards, were determined. In addition, the effect of adding melamine-urea-formaldehyde (MUF) resin to UF adhesive on the properties of the boards was investigated. Replacing conventional sound wood particles with deadwood particles leads to deterioration of the physical and mechanical properties of the boards. The boards from deadwood particles absorb more water and swell more. The bending strength (MOR), modulus of elasticity in bending (MOE), and internal bonding (IB) values for boards with 100% deadwood particles are reduced by 26.5%, 23.1%, and 72.4%, respectively, compared to reference boards from sound wood particles. Despite this, a significant advantage is that boards made from 100% deadwood particles are characterized by 34.5% less formaldehyde content than reference boards made from conventional sound wood. Moreover, adding 3% of MUF resin to UF adhesive increases MOR, MOE, and IB by 44.1%, 43.3%, and 294.4%, respectively.
- Open Access
- 17 December 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (7) , 655-667
Wood-adhesive bond loaded in mode II: experimental and numerical analysis using elasto-plastic and fracture mechanics models
The goal of the study was to analyze fracture properties of adhesive bond using a three-point end-notched flexure test and the compliance-based beam method. Critical strain energy release rates (G IIc ) and cohesive laws were obtained for adhesive bonds made of European beech (Fagus sylvatica L.) and adhesives such as EPI, MUF, PRF and PUR. The experiments were assisted with FE analyses employing three different material models of wood: elastic (Elas), symmetric elasto-plastic (EP) and elasto-plastic with different compressive and tensile yield stresses parallel to fiber (EP+). The highest mean G IIc was achieved for PUR (5.40 Nmm−1) and then decreased as follows: 2.33, 1.80, 1.59 Nmm−1 for MUF, EPI, and PRF, respectively. The failure of bondline was brittle and occurred at bondline for EPI, MUF and PRF, and ductile and commonly occurring in wood for PUR adhesive. The FE simulations employing cohesive models agreed well with the experimental findings for all adhesives. FE model with Elas material was found accurate enough for EPI, MUF and PRF adhesives. For PUR adhesive, the model EP+ was found to be the most accurate in prediction of maximal force. The impact of friction between lamellas may be up to 4.2% when varying friction coefficient from 0 to 1. The impact of the grain angle distortion (α) with respect to longitudinal specimen axis showed its high influence on resulting stiffness and maximal force. It was found that three-point end-notched test is suitable for EPI, MUF, and PRF, while it is less appropriate for a bond with PUR adhesive due to notable plastic behavior.
- 17 December 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (7) , 655-667
Open AccessWood-adhesive bond loaded in mode II: experimental and numerical analysis using elasto-plastic and fracture mechanics models
The goal of the study was to analyze fracture properties of adhesive bond using a three-point end-notched flexure test and the compliance-based beam method. Critical strain energy release rates (G IIc ) and cohesive laws were obtained for adhesive bonds made of European beech (Fagus sylvatica L.) and adhesives such as EPI, MUF, PRF and PUR. The experiments were assisted with FE analyses employing three different material models of wood: elastic (Elas), symmetric elasto-plastic (EP) and elasto-plastic with different compressive and tensile yield stresses parallel to fiber (EP+). The highest mean G IIc was achieved for PUR (5.40 Nmm−1) and then decreased as follows: 2.33, 1.80, 1.59 Nmm−1 for MUF, EPI, and PRF, respectively. The failure of bondline was brittle and occurred at bondline for EPI, MUF and PRF, and ductile and commonly occurring in wood for PUR adhesive. The FE simulations employing cohesive models agreed well with the experimental findings for all adhesives. FE model with Elas material was found accurate enough for EPI, MUF and PRF adhesives. For PUR adhesive, the model EP+ was found to be the most accurate in prediction of maximal force. The impact of friction between lamellas may be up to 4.2% when varying friction coefficient from 0 to 1. The impact of the grain angle distortion (α) with respect to longitudinal specimen axis showed its high influence on resulting stiffness and maximal force. It was found that three-point end-notched test is suitable for EPI, MUF, and PRF, while it is less appropriate for a bond with PUR adhesive due to notable plastic behavior.
- Open Access
- 14 January 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 74 (9) , 899-904
Micromechanical properties of beech cell wall measured by micropillar compression test and nanoindentation mapping
Wood exhibits very different behavior and properties at different scales. One important scale is the cell wall (CW) that is commonly tested by nanoindentation. Common nanoindentation provides important insight into the material but has limitations because it does not apply uniaxial stress and provides data from single spots. Therefore, the aim was to examine beech CW using two state-of-the-art techniques: micropillar compression (MCo) and nanoindentation mapping (NIP). The mean strength of the beech CW was found to be about 276 MPa and the mean yield stress was 183 MPa. These values were higher than those in most cited literature, which was attributed to the fact that libriform fibers from beech late wood were measured. Mean E obtained from MCo was about 7.95 GPa, which was lower than the values obtained on a macrolevel and about 61% of the value obtained from NIP. NIP also showed that E of the CW around the middle lamella (ML) was about 64% of the value at the location attributed to the S2 layer. Lower E from MCo may be caused by sinking of the micropillar into the wood structure under the load. Failure of the micropillars showed gradual collapse into themselves, with debonding at the S3 layer or the MLs.
- 14 January 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 74 (9) , 899-904
Open AccessMicromechanical properties of beech cell wall measured by micropillar compression test and nanoindentation mapping
Wood exhibits very different behavior and properties at different scales. One important scale is the cell wall (CW) that is commonly tested by nanoindentation. Common nanoindentation provides important insight into the material but has limitations because it does not apply uniaxial stress and provides data from single spots. Therefore, the aim was to examine beech CW using two state-of-the-art techniques: micropillar compression (MCo) and nanoindentation mapping (NIP). The mean strength of the beech CW was found to be about 276 MPa and the mean yield stress was 183 MPa. These values were higher than those in most cited literature, which was attributed to the fact that libriform fibers from beech late wood were measured. Mean E obtained from MCo was about 7.95 GPa, which was lower than the values obtained on a macrolevel and about 61% of the value obtained from NIP. NIP also showed that E of the CW around the middle lamella (ML) was about 64% of the value at the location attributed to the S2 layer. Lower E from MCo may be caused by sinking of the micropillar into the wood structure under the load. Failure of the micropillars showed gradual collapse into themselves, with debonding at the S3 layer or the MLs.
- Open Access
- 9 March 2019
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 73 (7) , 663-672
Thermally modified (TM) beech wood: compression properties, fracture toughness and cohesive law in mode II obtained from the three-point end-notched flexure (3ENF) test
The fracture properties of thermally modified beech ( Fagus sylvatica ) wood (TMW) at 180° and 200°C were evaluated in mode II using the three-point end-notched flexure (3ENF) scheme assisted by three-dimensional (3D) stereovision equipment for obtaining displacements and strains. The compliance-based beam method (CBBM) provided the strain energy release rates ( G II ) of TMW and cohesive laws for both native wood (W) and TMW. Based on the CBBM and equivalent crack length approach (ECLA), G II was obtained directly from the force-deflection data. The thermal modification (TM) process reduced the compressive strength by 4.4% and increased the compressive elastic modulus by 38.3%, whereas G II was reduced substantially by 40.8% and 67.9% at TM 180°C and TM 200°C , respectively. TM also increased wood brittleness that was visible on the displacement slip reduction. The resulting mean cohesive models can be used for numerical analyses. The fracture properties of TMW have to be taken into consideration for constructional wood application, when cyclic loading may lead to microcracking and material fatigue.
- 9 March 2019
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 73 (7) , 663-672
Open AccessThermally modified (TM) beech wood: compression properties, fracture toughness and cohesive law in mode II obtained from the three-point end-notched flexure (3ENF) test
The fracture properties of thermally modified beech ( Fagus sylvatica ) wood (TMW) at 180° and 200°C were evaluated in mode II using the three-point end-notched flexure (3ENF) scheme assisted by three-dimensional (3D) stereovision equipment for obtaining displacements and strains. The compliance-based beam method (CBBM) provided the strain energy release rates ( G II ) of TMW and cohesive laws for both native wood (W) and TMW. Based on the CBBM and equivalent crack length approach (ECLA), G II was obtained directly from the force-deflection data. The thermal modification (TM) process reduced the compressive strength by 4.4% and increased the compressive elastic modulus by 38.3%, whereas G II was reduced substantially by 40.8% and 67.9% at TM 180°C and TM 200°C , respectively. TM also increased wood brittleness that was visible on the displacement slip reduction. The resulting mean cohesive models can be used for numerical analyses. The fracture properties of TMW have to be taken into consideration for constructional wood application, when cyclic loading may lead to microcracking and material fatigue.
- 1 December 2017
- Published by Elsevier in Engineering Structures
- Vol. 152, 180-187
Experimental testing and theoretical prediction of traditional dowel-type connections in tension parallel to grain
- 1 December 2017
- Published by Elsevier in Engineering Structures
- Vol. 152, 180-187
Experimental testing and theoretical prediction of traditional dowel-type connections in tension parallel to grain