Frank Mauseth
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Frank Mauseth has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
- Hans Kristian Meyer
SINTEF Energy Research
15 shared publications Erling Ildstad
12 shared publicationsSverre Hvidsten
SINTEF Energy Research Sem Sælands vei 11 7034 Trondheim, Norway
11 shared publications- Robert Marskar
Sintef Energy Research, Sem Sælands vei 11, 7034 Trondheim, Norway
9 shared publications Atle Pedersen
SINTEF Energy Research, Trondheim, Norway
5 shared publications- Emre Kantar
SINTEF Energy Research, Trondheim, Norway
4 shared publications
Latest Publications
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 518-521
DC Breakdown in a Sphere-Plane Gap in Pressurized Synthetic Air
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 518-521
DC Breakdown in a Sphere-Plane Gap in Pressurized Synthetic Air
- Open Access
- 8 January 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (2) , 025210
Statistical time lags in air—pressure and polarity dependence
This paper investigates the influence of gas pressure on the polarity dependence of statistical time lags in air for a needle-plane gap. The needle-plane gap was stressed by a DC step voltage that lasted 10 s. The positive streamers were observed to have shorter time lags than negative at 1 bar absolute pressure. This polarity dependence was reversed at 3 bar and negligible at 5 bar. Simulations were performed to study this pressure dependence. These simulations support that detachment from negative ions is the main source to start electrons for positive streamers. For negative streamers, the conclusions are less clear. Based on the simulation results, detachment from negative ions inside the inception region was ruled out and field emission did not provide a consistent explanation across all pressure levels for negative streamers in these experiments. It is speculated that a field dependent surface effect, potentially related to secondary emission, dominates for negative streamers.
- 8 January 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (2) , 025210
Open AccessStatistical time lags in air—pressure and polarity dependence
This paper investigates the influence of gas pressure on the polarity dependence of statistical time lags in air for a needle-plane gap. The needle-plane gap was stressed by a DC step voltage that lasted 10 s. The positive streamers were observed to have shorter time lags than negative at 1 bar absolute pressure. This polarity dependence was reversed at 3 bar and negligible at 5 bar. Simulations were performed to study this pressure dependence. These simulations support that detachment from negative ions is the main source to start electrons for positive streamers. For negative streamers, the conclusions are less clear. Based on the simulation results, detachment from negative ions inside the inception region was ruled out and field emission did not provide a consistent explanation across all pressure levels for negative streamers in these experiments. It is speculated that a field dependent surface effect, potentially related to secondary emission, dominates for negative streamers.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (1) , 342-351
Aging of Environmentally Friendly Insulation Gases by Free-Burning Arcs: 7.5% C5-Fluoroketone With Technical Air
This paper explores how ageing by free-burning arcs affects the dielectric properties and decomposition of a mixture of 7.5% C5-fluoroketone (C5-FK) with 92.5% technical air (79% N2, 21% O2) at a pressure of 1.3 bar absolute. The gas is aged by exposure to consecutive arcs with a cumulative energy ∼315 kJ, a level relevant to medium voltage load break switches (LBS). To assess the long-term insulation performance, lightning impulse (LI) and AC breakdown tests are performed in a rod-plane electrode configuration before and after the ageing process. Additionally, gas decomposition is examined using gas chromatography and mass spectrometry. The results suggest that the LI breakdown voltage of the C5-FK/air mixture may decrease after ageing, likely due to C5-FK decomposition. Calculation of electron transport coefficients shows reduced attachment with C5-FK dissociation, which may decrease the discharge time delay. However, the discharge delay effects might not be observed in case of a slowly changing field, explaining why the AC breakdown voltage appears to be unaffected by ageing.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (1) , 342-351
Aging of Environmentally Friendly Insulation Gases by Free-Burning Arcs: 7.5% C5-Fluoroketone With Technical Air
This paper explores how ageing by free-burning arcs affects the dielectric properties and decomposition of a mixture of 7.5% C5-fluoroketone (C5-FK) with 92.5% technical air (79% N2, 21% O2) at a pressure of 1.3 bar absolute. The gas is aged by exposure to consecutive arcs with a cumulative energy ∼315 kJ, a level relevant to medium voltage load break switches (LBS). To assess the long-term insulation performance, lightning impulse (LI) and AC breakdown tests are performed in a rod-plane electrode configuration before and after the ageing process. Additionally, gas decomposition is examined using gas chromatography and mass spectrometry. The results suggest that the LI breakdown voltage of the C5-FK/air mixture may decrease after ageing, likely due to C5-FK decomposition. Calculation of electron transport coefficients shows reduced attachment with C5-FK dissociation, which may decrease the discharge time delay. However, the discharge delay effects might not be observed in case of a slowly changing field, explaining why the AC breakdown voltage appears to be unaffected by ageing.
- 22 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 32 (3) , 1528-1538
Aging of Environmentally Friendly Insulation Gases by Free-Burning Arcs: Technical Air
This paper investigates the effect of ageing due to free-burning arcs on the dielectric performance and the chemical composition of technical air (79% N2, 21% O2) at 1.3 bar absolute pressure. The ageing is performed by exposing the gas to a series of arcs dissipating an accumulated energy of more than 300 kJ, a level corresponding to relevant arcing energies for medium voltage load break switches. To evaluate the long-term dielectric performance, lightning impulse (LI) and power frequency AC breakdown tests are conducted in a 10 mm rod-plane gap before and after ageing. Gas decomposition is also investigated with gas chromatography coupled with mass-spectrometry. Results indicate that the LI breakdown voltage of air may enhance temporarily after arcing. This is probably due to the formation of short-lived air by-products (e.g., NO, NO2, NO3 and O3) which may reduce initial electron generation. However, changes in AC breakdown voltage might not be that significant as the presence of primary electrons is presumably guaranteed in the latter case.
- 22 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 32 (3) , 1528-1538
Aging of Environmentally Friendly Insulation Gases by Free-Burning Arcs: Technical Air
This paper investigates the effect of ageing due to free-burning arcs on the dielectric performance and the chemical composition of technical air (79% N2, 21% O2) at 1.3 bar absolute pressure. The ageing is performed by exposing the gas to a series of arcs dissipating an accumulated energy of more than 300 kJ, a level corresponding to relevant arcing energies for medium voltage load break switches. To evaluate the long-term dielectric performance, lightning impulse (LI) and power frequency AC breakdown tests are conducted in a 10 mm rod-plane gap before and after ageing. Gas decomposition is also investigated with gas chromatography coupled with mass-spectrometry. Results indicate that the LI breakdown voltage of air may enhance temporarily after arcing. This is probably due to the formation of short-lived air by-products (e.g., NO, NO2, NO3 and O3) which may reduce initial electron generation. However, changes in AC breakdown voltage might not be that significant as the presence of primary electrons is presumably guaranteed in the latter case.
- Open Access
- 1 October 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (10) , 105017
Streamer inception probability in air at atmospheric pressure – an experimental and theoretical analysis
We consider a self-consistent and probabilistic formulation of the classical Raether–Meek streamer inception model, and compare it with dedicated experiments. Our approach is based on the statistical evaluation of a first critical electron. This is done by evaluating the Raether–Meek integral for arbitrary starting positions of the first electron, and evaluating the size of the region in which the electrons can transition into a streamer. Then, using an ensemble-averaged model for the negative ion distribution which acts as a source of initial electrons, we compute the time-dependent probability of streamer inception. Unlike the standard Meek-based inception model, the experiments show that the generalized formulation is valid for both voltage polarities, but in return it requires knowledge about the initial ion distribution and electron detachment rate.
- 1 October 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (10) , 105017
Open AccessStreamer inception probability in air at atmospheric pressure – an experimental and theoretical analysis
We consider a self-consistent and probabilistic formulation of the classical Raether–Meek streamer inception model, and compare it with dedicated experiments. Our approach is based on the statistical evaluation of a first critical electron. This is done by evaluating the Raether–Meek integral for arbitrary starting positions of the first electron, and evaluating the size of the region in which the electrons can transition into a streamer. Then, using an ensemble-averaged model for the negative ion distribution which acts as a source of initial electrons, we compute the time-dependent probability of streamer inception. Unlike the standard Meek-based inception model, the experiments show that the generalized formulation is valid for both voltage polarities, but in return it requires knowledge about the initial ion distribution and electron detachment rate.
- 6 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 31 (5) , 2485-2493
Lightning Impulse Testing in Short Air-Gaps and Memory Effect of Previous Discharges
This paper reports on an observed phenomenon of increasing breakdown voltage while performing standard up and down lightning impulse (LI) testing in short air-gaps with weakly non-uniform field in an enclosed volume. The phenomenon could occur due to accumulation of space charges in the gap, changes in the chemical composition of the insulation gas, and/or changes in electrode surface due to discharges. To investigate the effect of these factors, LI tests are carried out in a 10 mm rod-plane air gap using four different methods: 1) ion flushing by DC voltage application in between LI shots, 2) with opposite polarity LI intertwined, 3) using forced air flow by a fan during the test, and 4) a reference test without any fan or voltage application. Results indicate that the phenomenon is more likely to be caused by formation of electronegative byproducts, e.g., ozone. Ozone was also experimentally detected near the test gap followed by consecutive LI breakdowns. It was found that air circulation rapidly reduces ozone concentration, which may explain why the increasing trend is not observed when a fan is used. Calculation of electron transport coefficients indicates that lack of primary electrons might be the prime reason of the increased impulse breakdown voltage of the air gap in presence of ozone.
- 6 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 31 (5) , 2485-2493
Lightning Impulse Testing in Short Air-Gaps and Memory Effect of Previous Discharges
This paper reports on an observed phenomenon of increasing breakdown voltage while performing standard up and down lightning impulse (LI) testing in short air-gaps with weakly non-uniform field in an enclosed volume. The phenomenon could occur due to accumulation of space charges in the gap, changes in the chemical composition of the insulation gas, and/or changes in electrode surface due to discharges. To investigate the effect of these factors, LI tests are carried out in a 10 mm rod-plane air gap using four different methods: 1) ion flushing by DC voltage application in between LI shots, 2) with opposite polarity LI intertwined, 3) using forced air flow by a fan during the test, and 4) a reference test without any fan or voltage application. Results indicate that the phenomenon is more likely to be caused by formation of electronegative byproducts, e.g., ozone. Ozone was also experimentally detected near the test gap followed by consecutive LI breakdowns. It was found that air circulation rapidly reduces ozone concentration, which may explain why the increasing trend is not observed when a fan is used. Calculation of electron transport coefficients indicates that lack of primary electrons might be the prime reason of the increased impulse breakdown voltage of the air gap in presence of ozone.
- 17 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 30 (6) , 2862-2869
Surface Flashover Over a Microprofiled Cylinder in Air
Increasing the lightning impulse (LI) flashover voltage of insulators can require significant changes to the geometry and material properties of the insulator or electrodes. In some cases, such changes can be difficult to implement as they may require more volume or may compromise e.g. mechanical properties of the insulating parts. In this work, a new micro-scale surface profile which inhibits streamer discharge propagation without introducing major changes to the insulation system geometry or materials is demonstrated. Polyoxymethylene (POM) cylinders with 25 % glass fibre in air were machined with 0.5x0.4 mm rectangular grooves spaced 0.6 mm apart and stressed with LIs. A non-profiled cylinder and a cylinder with a larger, semi-circular grooves were tested for comparison. The cylinders were tested in a 48.5 mm atmospheric air gap with an exposed triple junction as the positive electrode. The rectangular surface profiles increased the LI flashover voltage (U 50 %) from 70.0 to 96.5 kV peak . High-speed imaging showed positive surface streamer discharges stopping on the surface profiles. Discharge inception calculations were used to explain the influence of the surface profile on the flashover process. The results are relevant for technological applications with electrically stressed solid insulators in gases.
- 17 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 30 (6) , 2862-2869
Surface Flashover Over a Microprofiled Cylinder in Air
Increasing the lightning impulse (LI) flashover voltage of insulators can require significant changes to the geometry and material properties of the insulator or electrodes. In some cases, such changes can be difficult to implement as they may require more volume or may compromise e.g. mechanical properties of the insulating parts. In this work, a new micro-scale surface profile which inhibits streamer discharge propagation without introducing major changes to the insulation system geometry or materials is demonstrated. Polyoxymethylene (POM) cylinders with 25 % glass fibre in air were machined with 0.5x0.4 mm rectangular grooves spaced 0.6 mm apart and stressed with LIs. A non-profiled cylinder and a cylinder with a larger, semi-circular grooves were tested for comparison. The cylinders were tested in a 48.5 mm atmospheric air gap with an exposed triple junction as the positive electrode. The rectangular surface profiles increased the LI flashover voltage (U 50 %) from 70.0 to 96.5 kV peak . High-speed imaging showed positive surface streamer discharges stopping on the surface profiles. Discharge inception calculations were used to explain the influence of the surface profile on the flashover process. The results are relevant for technological applications with electrically stressed solid insulators in gases.
- Open Access
- 16 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Surface Flashover over a Profiled Cylinder in Air
The effect of a small-scale surface profile on the lightning impulse (LI) surface flashover over 30 mm diameter polyoxymethylene (POM) cylinders with 25 % glass fibre in air was studied. The cylinder surface was machined with 0.5x0.4 mm trenches spaced 0.6 mm apart. A non-profiled cylinder was used as a reference. The cylinders were tested in a 48.5 mm atmospheric air gap with an exposed triple junction as the positive electrode. The surface profiles increased the LI flashover voltage (U 50% ) from 70.0 to 96.5 kV peak . High-speed imaging showed surface streamer discharges stopping on the surface profiles. Discharge inception calculations were used to explain the influence of the surface profile on the flashover process. The results are relevant for technological applications with electrically stressed solid insulators in gases.
- 16 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessSurface Flashover over a Profiled Cylinder in Air
The effect of a small-scale surface profile on the lightning impulse (LI) surface flashover over 30 mm diameter polyoxymethylene (POM) cylinders with 25 % glass fibre in air was studied. The cylinder surface was machined with 0.5x0.4 mm trenches spaced 0.6 mm apart. A non-profiled cylinder was used as a reference. The cylinders were tested in a 48.5 mm atmospheric air gap with an exposed triple junction as the positive electrode. The surface profiles increased the LI flashover voltage (U 50% ) from 70.0 to 96.5 kV peak . High-speed imaging showed surface streamer discharges stopping on the surface profiles. Discharge inception calculations were used to explain the influence of the surface profile on the flashover process. The results are relevant for technological applications with electrically stressed solid insulators in gases.
- Open Access
Evolution of positive streamers in air over non-planar dielectrics: Experiments and simulations
We study positive streamers in air propagating along polycarbonate dielectric plates with and without small-scale surface profiles. The streamer development was documented using light-sensitive high-speed cameras and a photo-multiplier tube, and the experimental results were compared with 2D fluid streamer simulations. Two profiles were tested, one with 0.5 mm deep semi-circular corrugations and one with 0.5 mm deep rectangular corrugations. A non-profiled surface was used as a reference. Both experiments and simulations show that the surface profiles lead to significantly slower surface streamers, and also reduce their length. The rectangular-cut profile obstructs the surface streamer more than the semi-circular profile. We find quantitative agreement between simulations and experiments. For the surface with rectangular grooves, the simulations also reveal a complex propagation mechanism where new positive streamers re-ignite inside the surface profile corrugations. The results are of importance for technological applications involving streamers and solid dielectrics.
Open AccessEvolution of positive streamers in air over non-planar dielectrics: Experiments and simulations
We study positive streamers in air propagating along polycarbonate dielectric plates with and without small-scale surface profiles. The streamer development was documented using light-sensitive high-speed cameras and a photo-multiplier tube, and the experimental results were compared with 2D fluid streamer simulations. Two profiles were tested, one with 0.5 mm deep semi-circular corrugations and one with 0.5 mm deep rectangular corrugations. A non-profiled surface was used as a reference. Both experiments and simulations show that the surface profiles lead to significantly slower surface streamers, and also reduce their length. The rectangular-cut profile obstructs the surface streamer more than the semi-circular profile. We find quantitative agreement between simulations and experiments. For the surface with rectangular grooves, the simulations also reveal a complex propagation mechanism where new positive streamers re-ignite inside the surface profile corrugations. The results are of importance for technological applications involving streamers and solid dielectrics.