Bin Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bin Zhou has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Jun Wang
School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
3 shared publications- Jinbo Liu
School of Chemistry and Chemical Engineering
2 shared publications Peng Zhu
School of Chemistry and Chemical Engineering
2 shared publicationsRuiqi Shen
School of Chemistry and Chemical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
2 shared publications- Ruiqi Shen
School of Chemistry and Chemical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
2 shared publications Yong Li
School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing, China
2 shared publications
Latest Publications
- 30 September 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (44) , 21024-21040
Pulsed Airflow-Assisted Parametric Fabrication of Energetic Microspheres: Gel-Mediated Interfacial Reinforcement for Precise Energy Regulation
- 30 September 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (44) , 21024-21040
Pulsed Airflow-Assisted Parametric Fabrication of Energetic Microspheres: Gel-Mediated Interfacial Reinforcement for Precise Energy Regulation
- 3 January 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (2) , 1066-1079
Construction of Ultra-Mixed Energetic Composite Systems by Micro Continuous Flow Coupled with Spray Drying Technology
- 3 January 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (2) , 1066-1079
Construction of Ultra-Mixed Energetic Composite Systems by Micro Continuous Flow Coupled with Spray Drying Technology
- Open Access
The Role of Graphene Oxide in the Exothermic Mechanism of Al/CuO Nanocomposites
Metastable intermixed composites (MICs) have received increasing attention in the field of energy materials in recent years due to their high energy and good combustion performance. The exploration of ways of improving their potential release of heat is still underway. In this study, Al–CuO/graphene oxide (GO) nanocomposites were prepared using a combination of the self-assembly and in-suit synthesis methods. The formulation and experimental conditions were also optimized to maximize the exothermic heat. The DSC analysis shows that the addition of the GO made a significant contribution to the exothermic effect of the nanothermite. Compared with the Al–CuO nanothermite, the exothermic heat of the Al–CuO/GO nanocomposites increase by 306.9–1166.3 J/g and the peak temperatures dropped by 7.9–26.4 °C with different GO content. The reaction mechanism of the nanocomposite was investigated using a DSC and thermal reaction kinetics analysis. It was found that, compared with typical thermite reactions, the addition of the GO changed the reaction pathway of the nanothermite. The reaction products included CuAlO2. Moreover, the combustion properties of nanocomposite were investigated. This work reveals the unique mechanism of GO in thermite reactions, which may promote the application of carbon materials in nanothermite.
Open AccessThe Role of Graphene Oxide in the Exothermic Mechanism of Al/CuO Nanocomposites
Metastable intermixed composites (MICs) have received increasing attention in the field of energy materials in recent years due to their high energy and good combustion performance. The exploration of ways of improving their potential release of heat is still underway. In this study, Al–CuO/graphene oxide (GO) nanocomposites were prepared using a combination of the self-assembly and in-suit synthesis methods. The formulation and experimental conditions were also optimized to maximize the exothermic heat. The DSC analysis shows that the addition of the GO made a significant contribution to the exothermic effect of the nanothermite. Compared with the Al–CuO nanothermite, the exothermic heat of the Al–CuO/GO nanocomposites increase by 306.9–1166.3 J/g and the peak temperatures dropped by 7.9–26.4 °C with different GO content. The reaction mechanism of the nanocomposite was investigated using a DSC and thermal reaction kinetics analysis. It was found that, compared with typical thermite reactions, the addition of the GO changed the reaction pathway of the nanothermite. The reaction products included CuAlO2. Moreover, the combustion properties of nanocomposite were investigated. This work reveals the unique mechanism of GO in thermite reactions, which may promote the application of carbon materials in nanothermite.
- 13 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 41 (9) , 1416-1419
Novel Electro-Explosive Device Incorporating a Planar Transient Suppression Diode
In this letter, a novel, electrostatic discharge tolerant, semiconductor-based electro-explosive device was presented. The device which was called integrated semiconductor bridge (ISCB) chip consists of a monocrystalline silicon heating element, which was utilized to ignite pyrotechnic mix in weapon. Two planar transient suppression diode arrays were incorporated into the chip to protect against electrostatic discharge events. The characteristic of transient suppression diode array and electric discharge characteristic of the ISCB was tested by a capacitive discharge unit. Meanwhile, the behavior of the ISCB during electrostatic discharge events was also tested with a human body electrostatic discharge model. The results showed that the ISCB chip provided advantages including small size, fast ignition, electrostatic discharge insensitivity and low initiation energy applications.
- 13 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 41 (9) , 1416-1419
Novel Electro-Explosive Device Incorporating a Planar Transient Suppression Diode
In this letter, a novel, electrostatic discharge tolerant, semiconductor-based electro-explosive device was presented. The device which was called integrated semiconductor bridge (ISCB) chip consists of a monocrystalline silicon heating element, which was utilized to ignite pyrotechnic mix in weapon. Two planar transient suppression diode arrays were incorporated into the chip to protect against electrostatic discharge events. The characteristic of transient suppression diode array and electric discharge characteristic of the ISCB was tested by a capacitive discharge unit. Meanwhile, the behavior of the ISCB during electrostatic discharge events was also tested with a human body electrostatic discharge model. The results showed that the ISCB chip provided advantages including small size, fast ignition, electrostatic discharge insensitivity and low initiation energy applications.
- 8 December 2017
- Published by Taylor & Francis in Journal of Energetic Materials
- Vol. 36 (1) , 1-12
Research on the Electro-explosive Behaviors and the Ignition Performances of Energetic Igniters
This article describes the electro-explosive behaviors and the ignition performances of energetic igniters based on the combination of polysilicon film with Al/CuO nanoenergetic multilayer films (nEMFs).The ultra-high-speed framing camera images show that melting first occurs at the V-type angles and then expands to the entire bridge. The Al/CuO nEMF is heated and fired from below, forced to form lots of flyers with different sizes, ejected with the expansion of polysilicon plasma, and reacts exothermically to release a large quantity of energy. Furthermore, temperature diagnosis results demonstrate higher temperature products of energetic igniters. Ignition experiment at a standoff of 1.5 mm results show that the average firing voltage and the variance of energetic igniters are 28.50 V and 0.96, whereas those of polysilicon igniters are 32.05 V and 1.94.
- 8 December 2017
- Published by Taylor & Francis in Journal of Energetic Materials
- Vol. 36 (1) , 1-12
Research on the Electro-explosive Behaviors and the Ignition Performances of Energetic Igniters
This article describes the electro-explosive behaviors and the ignition performances of energetic igniters based on the combination of polysilicon film with Al/CuO nanoenergetic multilayer films (nEMFs).The ultra-high-speed framing camera images show that melting first occurs at the V-type angles and then expands to the entire bridge. The Al/CuO nEMF is heated and fired from below, forced to form lots of flyers with different sizes, ejected with the expansion of polysilicon plasma, and reacts exothermically to release a large quantity of energy. Furthermore, temperature diagnosis results demonstrate higher temperature products of energetic igniters. Ignition experiment at a standoff of 1.5 mm results show that the average firing voltage and the variance of energetic igniters are 28.50 V and 0.96, whereas those of polysilicon igniters are 32.05 V and 1.94.
- 9 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 45 (9) , 2486-2491
Measurements and Analyses of Electro-Exploding Products Generated by Semiconductor Bridge Igniters
In an effort to investigate the characteristics of electro-exploding products generated by Al/CuO-semiconductor bridge igniters, high-speed camera and spectrum diagnosis systems are employed in this paper. By using the high-speed camera system, the electro-exploding processes are recorded and the results indicate that electro-exploding processes include extrinsic conduction, intrinsic excitation, melting, vaporization, plasma discharging, and Al/CuO combustion. During this process, the spatial dimensions of plasma could reach to 8.7 mm in vertical direction under excitation energy of$47~\mu \text {F}/50~\text {V}$ . Meanwhile, the Al/CuO films are ejected from ceramic housing by plasma shock wave, combust upon plasma and plume. According to the results from the spectrum diagnosis system, it is noted that the temperature maintains 4000–6500 K for$65~\mu \text{s}$ .- 9 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 45 (9) , 2486-2491
Measurements and Analyses of Electro-Exploding Products Generated by Semiconductor Bridge Igniters
In an effort to investigate the characteristics of electro-exploding products generated by Al/CuO-semiconductor bridge igniters, high-speed camera and spectrum diagnosis systems are employed in this paper. By using the high-speed camera system, the electro-exploding processes are recorded and the results indicate that electro-exploding processes include extrinsic conduction, intrinsic excitation, melting, vaporization, plasma discharging, and Al/CuO combustion. During this process, the spatial dimensions of plasma could reach to 8.7 mm in vertical direction under excitation energy of$47~\mu \text {F}/50~\text {V}$ . Meanwhile, the Al/CuO films are ejected from ceramic housing by plasma shock wave, combust upon plasma and plume. According to the results from the spectrum diagnosis system, it is noted that the temperature maintains 4000–6500 K for$65~\mu \text{s}$ .- 27 January 2017
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 77 (1) , 10101
Experiments and simulations on non-plasma ignition of semiconductor bridge igniter
Since semiconductor bridge (SCB) igniter has been invented, it is commonly considered as a plasma generator. However, the plasma ignition mechanism may be affected by the hotspot ignition temperature of the primary explosives that is lower than the melting point of SCB in the igniter. In an effort to investigate the non-plasma ignition performance of SCB igniter, a one-dimensional model was established for temperature distribution analysis under constant current and capacitor discharge excitation. The simulation results featured the progress of heat transfer and the energy level required by non-plasma ignition of SCB was estimated. Furthermore, sensitivity experiments were carried out to test simulation results and to obtain the firing current range of SCB igniter with lead styphnate (LTNR). Experiment results indicated that safety conditions are 1.953 A constant current input lasting 1 ms under constant current excitation and 7.072 V voltage input using 47 µF storage capacitor under capacitor discharge excitation. All-firing conditions of non-plasma ignition are 2.035 A constant current input lasting 1 ms under constant current excitation and 7.647 V voltage input using 47 µF storage capacitor under capacitor discharge excitation.
- 27 January 2017
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 77 (1) , 10101
Experiments and simulations on non-plasma ignition of semiconductor bridge igniter
Since semiconductor bridge (SCB) igniter has been invented, it is commonly considered as a plasma generator. However, the plasma ignition mechanism may be affected by the hotspot ignition temperature of the primary explosives that is lower than the melting point of SCB in the igniter. In an effort to investigate the non-plasma ignition performance of SCB igniter, a one-dimensional model was established for temperature distribution analysis under constant current and capacitor discharge excitation. The simulation results featured the progress of heat transfer and the energy level required by non-plasma ignition of SCB was estimated. Furthermore, sensitivity experiments were carried out to test simulation results and to obtain the firing current range of SCB igniter with lead styphnate (LTNR). Experiment results indicated that safety conditions are 1.953 A constant current input lasting 1 ms under constant current excitation and 7.072 V voltage input using 47 µF storage capacitor under capacitor discharge excitation. All-firing conditions of non-plasma ignition are 2.035 A constant current input lasting 1 ms under constant current excitation and 7.647 V voltage input using 47 µF storage capacitor under capacitor discharge excitation.