FBFilipe B. Marinho DE Barros

Filipe B. Marinho DE Barros

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Filipe B. Marinho DE Barros has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Preparing β-hemihydrate using massive and fibrous high-grade gypsum: from mineral-ore characterization to compressive strength assessment

    by Pedro L. Guzzo, Felipe S. Martins, Mateus L. Idelfonso, Carlos D.F. DE Araújo, Vanessa L.M. Lima, Filipe B.M. DE Barros, Marcelo F. Gomes, Áureo O.D. Machado

    Gypsum resources from the Araripe Sedimentary Basin (Northeastern, Brazil) are known for their mineralogical quality and simple mining practices. Among the varieties found there, two are notably pure: (i) a semi-opaque lump of coarse grains known locally as Johnson stone; (ii) a satin spar like form with fibers lying along the c-axis known as alabaster. The current practice has been to reject alabaster from the plaster manufacturing circuit. Questioning this, the aim here was to assess microscopic and structural properties of alabaster and Johnson stone after grinding, calcination and rehydration steps. Grinding and calcination were carried out in direct and inverse routes using ball milling and heating at atmospheric pressure. Rehydration of fine powders was designed to produce cubic specimens for compressive tests. X-ray diffraction, infrared spectroscopy and thermal analyses were adopted to assess structural changes related to gypsum-bassanite-gypsum conversions. Besides some peculiarities related to particle size, no deviation preventing alabaster processing was detected. The compressive strength measured in samples prepared with single and blended powders points to a rational destination of alabaster for plaster manufacturing. The inverse route can also be adopted for alabaster processing. An overview of the current challenges faced by the Araripe Gypsum Hub is updated.

  • Open Access

    Correlating particle size distribution and thermal decomposition of intensely ground limestone and dolostone with microstructure and structural changes

    by Filipe B. Marinho DE Barros, Ulysses P. DE Holanda Pereira, Maria Júlia S. Luis, Pedro L. Guzzo

    An extensive investigation in limestone and dolostone ground in a planetary ball mill was achieved bearing in mind the different paths often observed in particle size reduction and agglomeration between these rocks and their increasing use in ultrafine size ranges for eco-friendly engineering applications. Two samples ground (dry) in a planetary ball mill up to 32 h were examined using laser scattering, physisorption, electron microscopy, X-ray diffraction, infrared spectroscopy and thermal analysis. Static hardness and crystal grain sizes were measured in parent rock specimens. For limestone, the apparent grinding limit (12 µm) was reached after 1 h, and no changes were observed in lattice strain, crystallite size and infrared bands related to CO32- vibration modes. For dolostone, these properties changed significantly when the grinding limit (6 µm) was achieved (8 h). Calcite-aragonite transformation was mostly observed in intensely ground dolostone. The activation energy for thermal decomposition of calcite and dolomite was correlated with lattice strain and particle agglomeration. The lower grinding rate noticed for dolostone was attributed to its refined grain size. Distinct energy dissipation mechanisms were portrayed once the grinding limit was reached: agglomeration and deagglomeration cycles in limestone; plastic deformation and growth of strong agglomerates in dolostone.


  • Open Access

    An investigation on the physical properties of cementitious pastes modified with low dosage of waste glass powder and silica fume

    by André L.S. Patriota, Filipe B.M. Barros, Arnaldo M.P. Carneiro, Pedro L. Guzzo

    Portland cement (PC) production is among the industrial activities that most emit harmful gases. Its replacement to green binders turns into a timely issue to face the global restrictions due to climate changes. In this study, some properties of cementitious pastes prepared with waste packing glass powder (GP) and silica fume (SF) were characterized in line with a prefixed alkaline equivalent limit. These materials were obtained in Northeastern Brazil. Grinding operations used to produce GP into four size ranges ([45-75] µm, < 45 µm; [25-45] µm, < 25 µm) were disclosed. X ray diffraction showed that GP and SF substitutions did not change the hydration products commonly observed in PC pastes. The portlandite content measured with thermogravimetry was affected by GP size in both unitary and binary substitutions. The compressive strength measured after 56 days of curing was dependent on portlandite and void index contents measured in hardened pastes. Scanning electron microscopy coupled to energy dispersive spectroscopy were useful to show the effect of the particle size on the pozzolanic activity. It was found that 5% of PC replacement for GP < 25 µm was enough to raise the compressive strength by ~5%. For binary substitution, the strength increasing was ~ 20 %. The collectors of solid residues are the main players of waste glass recycling in Brazil. It is expected that the results of this study contribute to take out these workers from the fringes of the citizenship.


  • Enhancing the mechanical performance of plastering mortars with low levels of multilayer graphene and their chemical, structural, and microstructural characteristics

    by C.F. Nascimento, F.B. Barros, R.C. Manta, H.C.B. Nascimento, N.B. Lima, E.C. Costa, K.G.B. Alves, Y.V. Póvoas, E.C. Monteiro, N.B.D. Lima


  • Open Access

    CONCENTRAÇÃO DE ESCÓRIA METALURGICA DA LIGA FeSiMn POR MESA CONCENTRADORA WILFLEY

    by Raulim Oliveira Galvão, Filipe Brito Marinho Barros, Gabriella Katarine Silva Neto, José Carlos Silva Oliveira, Viviane de Cássia Paixão Andrade, Élyda Lima Silva, Belarmino Barbosa Lira

    A produção industrial da liga metálica ferrosiliciomanganês (FeSiMn) está intimamente ligada ao processo pirometalúrgico. Porém, devido às limitações desse processo, observa-se um elevado percentual da liga FeSiMn nas pilhas de rejeito. Neste contexto, o objetivo deste trabalho foi escalonar uma rota de recuperação utilizando uma mesa oscilatória Wilfley. Para o estudo foi utilizada cerca de 40 kg de escória metalúrgica da liga FeSiMn. Analisou-se as influências de 3 parâmetros fundamentais da mesa: granulometria (125µm), inclinação (2° e 4°) e amplitude (12 e 14 mm). A influência dos parâmetros da mesa oscilatória foi analisada pela variação do teor do concentrado e das recuperações mássica e metalúrgica. Para determinar o teor do concentrado empregou-se a técnica de fluorescência de raios-X (FRX). Com isso, constatou-se que os parâmetros amplitude e inclinação apresentaram uma menor influência sobre o teor e a recuperação mássica. No entanto, a granulometria apresentou uma variação significativa na recuperação metalúrgica. Assim, pode-se concluir que neste estudo a configuração que gerou uma maior eficiência no processo de concentração da liga FeSiMn utilizando a mesa oscilatória Wilfley foi: granulometria <125 µm; inclinação de 2°; e amplitude de 14 mm. Essa configuração apresentou uma recuperação metalúrgica de aproximadamente 50% da liga FeSiMn.