Piotr Olaszek

Remote visual inspections are valuable tools for maintaining bridges in safe operation. In the case of old structures with incomplete documentation, the verification of dimensions is also an essential aspect. This paper presents an attempt to use a Scanning Total Station (STS) and Unmanned Aerial Vehicle (UAV) for the inspection and inventory of bridge dimensions. The STS’s measurements are conducted by applying two methods: the direct method using a total station (TS) and advanced geometric analyses of the collected point cloud. The UAV’s measurements use a Structure from Motion (SfM) method. Verification tests were conducted on a steel truss railway bridge over the largest river in Poland. The measurements concerned both the basic dimensions of the bridge and the details of a selected truss connection. The STS identified a significant deviation in the actual geometry of the measured connection and the design documentation. The UAV’s inspection confirmed these findings. The integration of STS and UAV technologies has demonstrated significant advantages, including STS’s high accuracy in direct measurements, with deviations within acceptable engineering tolerances (below a few mm), and the UAV’s efficiency in covering large areas, achieving over 90% compliance with reference dimensions. This combined approach not only reduces operating costs and enhances safety by minimizing the need for heavy machinery or scaffolding but also provides a more comprehensive understanding of the structural condition.

Measurements of displacements of bridges under dynamic load are particularly difficult in the case of structures where access to the area under the tested structure is impossible. Then, remote measurement methods are preferred, such as interferometric radar. Interferometric radar has high accuracy when measuring displacement in the direction of its target axis. The problems appear when a bridge vibrates in two directions: horizontal (lateral or longitudinal) and vertical. The use of one radar to measure those vibrations may be impossible. This paper presents the application of a set of two interferometric radars to measure vertical vibration and horizontal longitudinal vibration with high accuracy. The method was positively verified by experimental tests on two railway bridges characterized by different levels of horizontal displacement. The accuracy of the radar measurements was tested by the direct measurement of vertical displacements using inductive gauges. In conclusion, in the case of vertical displacement measurements using one interferometric radar, the influence of horizontal displacements should be excluded. In the case of locating radars at the area of bridge supports, it is necessary to either use a set of two radars or first investigate the magnitude of possible horizontal displacements in relation to vertical displacements.

The article presents an investigation on the dynamic impact from passing trains on noise barriers. The effect was an investigation along two railway line sections: on the first section the barriers were located less than 3.8 m from the track axis and considerable distress of the barriers was observed; on the second section barriers of the same type were located 4.6 m from the track axis and no distress was noted. A method for determination of displacement occurring under aerodynamic loading is presented, based on measurement of vibration acceleration and calculation of double integral. The obtained results are compared with measurements from an interferometric radar. Parameters for analysis and assessment of the magnitude of dynamic impact from passing trains are proposed. The results of the analyses performed on the two railway line sections are compared. The article also presents laboratory tests of an undamaged noise barrier panel. Conclusions are formulated regarding the use of noise barriers susceptible to fatigue due to alternating positive and negative aerodynamic pressure peaks.

In the case of the monitoring of bridges, the determination of vertical displacements is one of the most important issues. A new measuring system has been developed and implemented for assessment of railway bridges based on measurements of the structural response to passing trains. The system uses inertial sensors: Inclinometers and accelerometers that do not need any referential points. The system records signals related to the passage of a train over a monitored bridge. The signals from inclinometers before the train’s entry are used to determine the static movement. Integrated signals from inclinometers and accelerometers are used to determine dynamic displacements when the train goes through the bridge. Signals from inclinometers are used to determine the so-called “quasi-static” component of the displacement and signal from the accelerometer to determine the dynamic component. Field tests have been carried out on a viaduct along a high-speed railway line. Periodic comparative measurements are carried out using a Total Station to verify static measurements and using inductive sensors to verify dynamic measurements. Tests of the system carried out so far have proven its usefulness for monitoring bridges in a high-speed railway (up to 200 km/h) with high accuracy while determining dynamic displacements.