ASAlireza Siadatan

Alireza Siadatan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alireza Siadatan has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Magnet-Utilization-Oriented PSO--FEA Optimization of a Ferrite Spoke-Type Rotor for Rare-Earth-Free EV Traction Motors

    by Fatemeh Ghalavand, Ilamparithi T. Chelvan, Afshin Rezaei-Zare, Alireza Siadatan

    Rare-earth-free traction motors are attractive for reducing magnet cost and material dependence, but ferrite is challenging to use in high-performance electric-vehicle (EV) machines because its remanence is much lower than that of neodymium-iron-boron (NdFeB). This work develops a magnet-utilization-oriented particle swarm optimization-finite-element analysis (PSO-FEA) procedure for a ferrite spoke rotor and evaluates it using the unchanged Chevrolet Bolt stator as a production EV benchmark. Seven rotor variables are optimized using the average air-gap flux density per unit magnet area as the magnet-utilization objective, and a remanence-normalized index is introduced for cross-material comparison.The optimized ferrite rotor produces an RMS no-load back-EMF within 5.2% of the NdFeB reference. At the rated maximum-torque-per-ampere (MTPA) operating point, it delivers 101.4% of the baseline torque while reducing torque ripple by 79.6%. Torque-speed efficiency and loss maps show that a broad high-efficiency region is retained and that the optimized rotor remains usable into the high-speed region. A severe negative d-axis current condition is also evaluated for demagnetization robustness, while the torque-normalized magnet cost is substantially reduced. The results show that flux concentration and increased saliency can compensate for a large part of the performance loss associated with ferrite's lower remanence, supporting the optimized spoke rotor as a practical rare-earth-free candidate for EV traction applications.

  • Design of a Compact WPT System Using DGS Resonators with Circular Edges in two Frequency Bands

    by Mahya Samadbeik, Alireza Siadatan, Abbas Ramazani, Akbar Dargahi

  • Retracted
    Open Access

    A Hybrid P&O-Fuzzy-Based Maximum Power Point Tracking (MPPT) Algorithm for Photovoltaic Systems Under Partial Shading Conditions

    by Hamed Karimi, Alireza Siadatan, Afshin Rezaei-Zare

    Photovoltaic arrays receive varying levels of solar radiation due to factors such as shadows created by clouds, surrounding buildings, and other obstructions. Therefore, an effective Maximum Power Point Tracking (MPPT) algorithm should be used to maximize power generation from non-uniform arrays. Most MPPT algorithms do not perform well during partial shadow conditions, as they can become trapped in local maxima and fail to identify the absolute global maximum point (GP). This paper proposes a new MPPT approach that combines Perturb & Observe (P&O) and Fuzzy Logic Controller (FLC) with the Particle Swarm Optimization (PSO) algorithm. The FLC algorithm is then used to maximize search accuracy. The configurations of this system and the study results demonstrate the dynamic and promising performance of the proposed method under various environmental and shading conditions. In addition to its simplicity and ease of implementation, the proposed algorithm exhibits high accuracy in tracking the maximum power point. This has been evidenced through both simulation and laboratory results of the hardware.


  • Open Access

    Design, modeling, prototyping, and comparison of a low‐cost, small‐size, and accurate sensorless driver for switched reluctance motor

    by Alireza Siadatan, Hossein Torkaman, Mehran Rafie

    A switched reluctance motor (SRM) is a low‐cost motor with a simple structure and variable speed industrial and home applications. This article presents the design, simulation, and development of a low‐cost, accurate, and small‐size sensorless driver for a 6/4 three‐phase SRM. In the algorithm, the (nonlinear) relation of the flux, current, and rotor (FCR) position is linearized to achieve a modified FCR model, in which the values of the most important points of the primary FCR are emphasized. The SRM parameters required for the design process are obtained using a 3D finite‐element method (FEM). The proposed method is simulated and then tested under different load and speed conditions. The results are compared with a conventional sensorless algorithm's results, and the reference data are obtained by a direct with‐sensor algorithm. The algorithm estimates the rotor position (error of 1.3%) between low to nominal speed of the selected SRM under both nominal and no‐load conditions. In comparison with the conventional algorithm, the proposed FCR model significantly reduces the calculation cost and memory demand by 66%. Finally, the proposed algorithm decreases the driver size and price by 64% and 85%, respectively.


  • Coordinated design of PSS and TCSC controllers using colonal selection algorithm for stability enhancement of dynamical power system

    by Elnaz Yasoubi, Mostafa Sedighizadeh, Alireza Siadatan

    This paper deals with the simultaneous application of thyristor controlled series capacitor based damping controller and power system stabilizer for stability improvement of dynamic power system. The Colonal selection algorithm is used to develop the control strategy for thyristor controlled series capacitor based damping controller and power system stabilizer. The new approach employs time-domain simulation based objective functions simultaneously to improve the optimization convergence rate in Colonal selection algorithm. The comparison analysis between conventional and smart control strategies based controllers is demonstrated. Single machine infinite bus system is tested under various operating conditions and disturbances to show the effectiveness of proposed control schemes. The results of simulations for a single machine infinite bus (SMIB) system equipped with the proposed PSS and TCSC controllers confirm that the new approach is effective in enhancing the system stability.


  • A filterless single-phase AC-AC converter based on coupled inductors with safe-commutation strategy and continuous input current

    by Soroush Esmaeili, Alireza Siadatan, Ali Zareian Jahromi, Peimaneh Shirazi

    A novel single phase ac-ac converter with no LC input/output filters is presented in this paper. The proposed converter has all the advantages of the previous single phase impedance source ac-ac converters; it can operate in buck/boost and in-phase/out-of phase with the input voltage, that makes it appropriate for voltage sags/swells compensator without any dc storage. A coupled transformer based on T-structure is utilized to give an opportunity to access desired output voltage with various duty cycles. In this topology snubber circuit is not required, because a safe commutation strategy enables to eliminate voltage and current spikes produced by short-circuit path. In addition, the converter performs in continuous current mode, so there is no inrush current. Also, the characteristic which the output voltage reverses or maintains phase angle with the input voltage is supported well, because the input and output share the same ground. Eventually, circuit analysis, operating principles and simulation results in MATLAB/SIMULINK are presented to verify the performance of the converter.


  • Thermal stability analysis of 6/4 switch reluctance motor using finite element method

    by Alireza Siadatan, S.H. Mirimani, Mahshid Shamei, Tohid Khalili

    This paper studies the thermal stability of a 6/4 switch reluctance machine under nominal operating condition. Transient finite elements method has been used to calculate the machine copper loss and the core loss in magnetic domain. To calculate the copper loss the precise evaluation of current was needed which has been obtained by applying a voltage sources as the input of the electrical circuit of the finite element method. Meanwhile the switching commands have been considered to give a real duty cycle. Moreover the Bertotti loss calculation method has been used to compute the core loss of the machine in the operating condition. The calculated losses in the magnetic domain has been imported to the thermal domain as the heat sources for analyzing the thermal stability of the machine in the operating condition. This study shows that the machine losses are mostly produced by copper loss as the machine does not contain permanent magnet materials to produce high value of flux density in all parts of machine simultaneously. In other words it is shown that most parts of the machine core does not contain high value of magnetic flux as there are just two conducting coils in each moment. Finally it is shown that by a well-designed machine a good thermal stability is feasible for a continuous operating condition.


  • Design and simulation of new method of a sensorless control of BLDC motor by usying of speed and rotor position method

    by Alireza Siadatan, Elnaz Yasoubi, Sam Ghasemi, Majid Hojjat

    This paper describes a new position and speed observer, for BLDCPM1 motor drive sensorless control, based on the line-to-line PM flux linkage estimation. Line-to-line PM flux linkage can be estimated based on measured phase currents and line to line voltage. The zero-crossing of the line-to-line PM flux linkage occurs right in the middle of two commutation points, which is used as a basis for the position and speed observer. Even if the proposed observer relies on the fundamental model of the machine, a safe starting strategy under heavy load torque, called I-f control, is used, with seamless transition to the proposed sensorless control. The I-f starting method allows low- speed sensorless control, without knowing the initial position, and without machine parameters identification. Digital simulations and experimental results are shown, demonstrating the reliability of position and speed observer for BLDC PM motor sensorless control operation.


  • Two-stage asymmetrical Γ-Z-source inverter with high voltage gain and reduced shoot-through duty ratio

    by Soroush Esmaeili, Shekouh Karimi, Pouya Tarassodi, Alireza Siadatan

    This study presents a novel inverter with high voltage gain based on asymmetrical Γ-Z-source topology. It employs one diode, one inductor and two capacitors more than the basic structure that obtains higher output voltage with reduced duty ratio. So, a reasonable modulation ratio is needed to gain desired boost factor which improves the network power quality. In this structure, unlike other Z-source topologies such as two-stage Quasi Z-source inverter, higher stages are not required for voltage gain boosting, owing to a Γ-shape coupled inductors is used in impedance network. This unique coupled transformer raises voltage gain significantly by lowering turns ratio that reduces the cost, volume and improves the efficiency. Moreover, the two-stage asymmetrical Γ-Z-source inverter is able to operate both in buck and boost mode and its input current is continuous. The proposed inverter is analyzed in steady state and simulation results are presented to verify the performance. As well as, simple boost control is used for simulations.