Samim Konjicija
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Samim Konjicija has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Abdulah Aksamovic
Faculty of Electrical Engineering, University of Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina
7 shared publications - Selma Grebović
Faculty of Electrical Engineering, University of Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina
5 shared publications - Zikrija Avdagic
Department of Computing and Informatics University of Sarajevo/Faculty of Electrical Engineering Sarajevo Bosnia and Herzegovina
5 shared publications Zikrija Avdagic
Dept. of Information Technologies, Faculty of Electrical Engineering, Sarajevo, Bosnia and Herzegovina
4 shared publicationsEmir Sokic
Faculty of Electrical Engineering, University of Sarajevo, Bosnia and Herzegovina
3 shared publications- Emir Sokic
Department of Automatic Control and Electronics, Faculty of Electrical Engineering, University of Sarajevo, Bosnia and Herzegovina
3 shared publications
Latest Publications
- Open Access
Investigation of lightning effects on solar power plants connected to transmission networks
The increasing integration of solar power plants into transmission grids has raised concerns about their vulnerability to disturbances, particularly lightning strokes. Solar energy, while offering significant environmental and economic benefits, faces challenges when connected to transmission lines that are prone to lightning discharges. This paper investigates the impact of lightning events on solar power plants, focusing on overvoltage effects. Lightning stroke simulations were conducted at various distances from the solar power plant along the transmission line, considering scenarios with and without surge arrester. Key lightning parameters such as peak current, front time, and tail time were varied to simulate different lightning strokes. The study also includes a Fourier transform analysis of the resulting overvoltages with and without a surge arrester, along with the Hilbert marginal spectrum of these overvoltages. The results provide insights into the effectiveness of surge arresters in mitigating lightning overvoltages and highlight the importance of proper protective measures for enhancing the reliability and safety of solar power plants connected to transmission networks.
Open AccessInvestigation of lightning effects on solar power plants connected to transmission networks
The increasing integration of solar power plants into transmission grids has raised concerns about their vulnerability to disturbances, particularly lightning strokes. Solar energy, while offering significant environmental and economic benefits, faces challenges when connected to transmission lines that are prone to lightning discharges. This paper investigates the impact of lightning events on solar power plants, focusing on overvoltage effects. Lightning stroke simulations were conducted at various distances from the solar power plant along the transmission line, considering scenarios with and without surge arrester. Key lightning parameters such as peak current, front time, and tail time were varied to simulate different lightning strokes. The study also includes a Fourier transform analysis of the resulting overvoltages with and without a surge arrester, along with the Hilbert marginal spectrum of these overvoltages. The results provide insights into the effectiveness of surge arresters in mitigating lightning overvoltages and highlight the importance of proper protective measures for enhancing the reliability and safety of solar power plants connected to transmission networks.
- Open Access
Integrating Floating Photovoltaics with Hydroelectricity
The transition process from fossil fuels to environmentally friendly renewable energy sources carries the risk of creating new environmental damages. Photovoltaic technology represents one of the alternatives with the least risk of harmful environmental impact. However, this technology has two important drawbacks: the significant land occupation for the installation of PV systems and the uncontrollability of production. By constructing floating photovoltaic plants on hydroelectric reservoirs, both of these problems can be reduced to an acceptable level. Some artificial reservoirs, originally built for hydroelectric power plants, have acquired a significant secondary function as recreational areas and fish breeding sites. Therefore, there is justified resistance from the local community to change the existing appearance and purpose of such reservoirs. This paper proposes a completely new concept of integrating the interests of the local community into such objects. In addition to preserving existing uses, the concept also offers new features. This can make the entire system environmentally friendly and sustainable. This paper details the technology behind the construction of floating photovoltaic power plants on artificial reservoirs and emphasizes their various advantages. These benefits include the non-utilization of cultivable land, the ease of assembly and construction, integration into existing power grids, and the potential to address electricity storage issues. For instance, Buško Lake, covering an area of km2, may host km2 of installed floating photovoltaic (FPV) facilities, enabling a total installed capacity of 240 MW. With an average of h of daily sunshine, this totals 2007 annual hours, equivalent to a 55 MW thermal power plant. An analysis showed that, with losses of 18.2%, the average annual production stands at 302 , translating to an annual production value of 18 million € at 60 €/MWh. The integration of this production into an existing hydroelectric power plant featuring an artificial reservoir might boost its output by 91%. The available transmission line capacity of 237 MW is shared between the hydroelectric power plant (HPP) and FPV; hence during the FPV maximum power generation time, the HPP halts its production. HPP Orlovac operates a small number of hours annually at full capacity (1489 h); therefore in combination with the FPV, this number can be increased to 2852 h. This integration maintains the lake’s functions in tourism and fishing while expanding its capabilities without environmental harm.Open AccessIntegrating Floating Photovoltaics with Hydroelectricity
The transition process from fossil fuels to environmentally friendly renewable energy sources carries the risk of creating new environmental damages. Photovoltaic technology represents one of the alternatives with the least risk of harmful environmental impact. However, this technology has two important drawbacks: the significant land occupation for the installation of PV systems and the uncontrollability of production. By constructing floating photovoltaic plants on hydroelectric reservoirs, both of these problems can be reduced to an acceptable level. Some artificial reservoirs, originally built for hydroelectric power plants, have acquired a significant secondary function as recreational areas and fish breeding sites. Therefore, there is justified resistance from the local community to change the existing appearance and purpose of such reservoirs. This paper proposes a completely new concept of integrating the interests of the local community into such objects. In addition to preserving existing uses, the concept also offers new features. This can make the entire system environmentally friendly and sustainable. This paper details the technology behind the construction of floating photovoltaic power plants on artificial reservoirs and emphasizes their various advantages. These benefits include the non-utilization of cultivable land, the ease of assembly and construction, integration into existing power grids, and the potential to address electricity storage issues. For instance, Buško Lake, covering an area of km2, may host km2 of installed floating photovoltaic (FPV) facilities, enabling a total installed capacity of 240 MW. With an average of h of daily sunshine, this totals 2007 annual hours, equivalent to a 55 MW thermal power plant. An analysis showed that, with losses of 18.2%, the average annual production stands at 302 , translating to an annual production value of 18 million € at 60 €/MWh. The integration of this production into an existing hydroelectric power plant featuring an artificial reservoir might boost its output by 91%. The available transmission line capacity of 237 MW is shared between the hydroelectric power plant (HPP) and FPV; hence during the FPV maximum power generation time, the HPP halts its production. HPP Orlovac operates a small number of hours annually at full capacity (1489 h); therefore in combination with the FPV, this number can be increased to 2852 h. This integration maintains the lake’s functions in tourism and fishing while expanding its capabilities without environmental harm. - Open Access
A Low Cost Real-Time Transient Recorder for High Voltage Systems
Large-scale incorporation of new energy generation units based on renewable sources, such as wind and photovoltaic power, drastically alters the structure of the power system. Because of the intermittent nature of these sources, switching in grids (connection and disconnection) occurs much more frequently than with conventional sources. As a result, the power system will inevitably experience a large number of transients, which raises questions about the stability of the system and the quality of the electrical energy. Therefore, measuring various types of transients in power system is crucial for stability, power quality, fault analysis, protection design, and insulation design. Transient recorders that are currently used are generally expensive and only suitable for particular locations in power systems. The number of installed transient recorders is insufficient for a comprehensive analysis of problems that may occur. Hence, it is important to have inexpensive and efficient transient recorders that can be installed at multiple points in the power system on various types of objects. It is also essential to have a transient record database with open access, which can be used by researchers to develop new analysis techniques based on artificial intelligence. This paper proposes an inexpensive measurement and acquisition system designed to record transient phenomena on different objects within the power system. The system is designed to use autonomous power, a standardized data acquisition module, a low-budget system for transmitting recorded transient events to the server via mobile network, and a sensor system adapted to the object where transients are recorded. The proposed system is designed to be used for all types of objects in the power system where transients may occur, such as power lines, transmission towers, surge arresters, and transformers. All components of the system are described, and the system is tested under laboratory conditions. The modular nature of the system allows customization to the specifics of the location in power system by choosing appropriate components. The calibration method of the custom designed Rogowski coil is described. The cost analysis of the proposed system and power consumption analysis are performed. The results show that the system’s performance meets application requirements at a low cost.
Open AccessA Low Cost Real-Time Transient Recorder for High Voltage Systems
Large-scale incorporation of new energy generation units based on renewable sources, such as wind and photovoltaic power, drastically alters the structure of the power system. Because of the intermittent nature of these sources, switching in grids (connection and disconnection) occurs much more frequently than with conventional sources. As a result, the power system will inevitably experience a large number of transients, which raises questions about the stability of the system and the quality of the electrical energy. Therefore, measuring various types of transients in power system is crucial for stability, power quality, fault analysis, protection design, and insulation design. Transient recorders that are currently used are generally expensive and only suitable for particular locations in power systems. The number of installed transient recorders is insufficient for a comprehensive analysis of problems that may occur. Hence, it is important to have inexpensive and efficient transient recorders that can be installed at multiple points in the power system on various types of objects. It is also essential to have a transient record database with open access, which can be used by researchers to develop new analysis techniques based on artificial intelligence. This paper proposes an inexpensive measurement and acquisition system designed to record transient phenomena on different objects within the power system. The system is designed to use autonomous power, a standardized data acquisition module, a low-budget system for transmitting recorded transient events to the server via mobile network, and a sensor system adapted to the object where transients are recorded. The proposed system is designed to be used for all types of objects in the power system where transients may occur, such as power lines, transmission towers, surge arresters, and transformers. All components of the system are described, and the system is tested under laboratory conditions. The modular nature of the system allows customization to the specifics of the location in power system by choosing appropriate components. The calibration method of the custom designed Rogowski coil is described. The cost analysis of the proposed system and power consumption analysis are performed. The results show that the system’s performance meets application requirements at a low cost.
- Open Access
An Approach for Estimating Lightning Current Parameters Using the Empirical Mode Decomposition Method
Lightning parameters are needed in different engineering applications. For the prediction of the severity of transient voltages in power systems, an accurate knowledge of the parameters of lightning currents is essential. All relevant standards and technical brochures recommend that lightning characteristics should be classified according to geographical regions instead of assuming that these characteristics are globally uniform. Many engineers and scientists suggest that better methods for lightning current measurements and analyses need to be developed. A system for direct lightning current measurements installed on Mount Lovćen is described in this paper. Observed data were analyzed, and statistical data on parameters that are of interest for engineering applications were obtained, as well as correlations between various lightning parameters. Furthermore, a novel approach for classifying and analyzing lightning data from direct measurements based on empirical mode decomposition (EMD) is proposed. Matlab was used as a tool for signal processing and statistical analysis. The methodology implemented in this work opens possibilities for automated analysis of large data sets and expressing lightning parameters in probabilistic terms from the data measured on site.
Open AccessAn Approach for Estimating Lightning Current Parameters Using the Empirical Mode Decomposition Method
Lightning parameters are needed in different engineering applications. For the prediction of the severity of transient voltages in power systems, an accurate knowledge of the parameters of lightning currents is essential. All relevant standards and technical brochures recommend that lightning characteristics should be classified according to geographical regions instead of assuming that these characteristics are globally uniform. Many engineers and scientists suggest that better methods for lightning current measurements and analyses need to be developed. A system for direct lightning current measurements installed on Mount Lovćen is described in this paper. Observed data were analyzed, and statistical data on parameters that are of interest for engineering applications were obtained, as well as correlations between various lightning parameters. Furthermore, a novel approach for classifying and analyzing lightning data from direct measurements based on empirical mode decomposition (EMD) is proposed. Matlab was used as a tool for signal processing and statistical analysis. The methodology implemented in this work opens possibilities for automated analysis of large data sets and expressing lightning parameters in probabilistic terms from the data measured on site.
- Open Access
- 29 April 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (9) , 4500
DC Cabling of Large-Scale Photovoltaic Power Plants
The development of Floating Solar Photovoltaic (FPV) systems is a sign of a promising future in the Renewable Energy field. Numerous solar modules and inverters are mounted on large-scale floating platforms. It is important to design the system so that the inverter operates in its optimum range most of the time. In order to achieve this goal on the DC side, serial and parallel connections of solar modules are used. As a result, the cabling of the PV array architecture is an important issue. Modern electrical installation design requires reducing costs in cabling materials, equipment installation, and maintenance. The reduction of losses and the amount of time required to complete the design are also significant. Therefore, the main topic of this paper is DC cabling in large-scale FPV power plants (>1 ). The serial-parallel (SP) connection scheme of solar modules and the percentage of power loss in DC cables are considered. Furthermore, a general method for determining cable lengths for FPV power plants is defined. The temperature influence on losses in DC cables is analyzed. A new method for determining the current at the maximum power point (MPP) as a function of temperature is proposed. A case study is conducted using a hypothetical 3 MW FPV power plant, and the obtained results are presented and analyzed.- 29 April 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (9) , 4500
Open AccessDC Cabling of Large-Scale Photovoltaic Power Plants
The development of Floating Solar Photovoltaic (FPV) systems is a sign of a promising future in the Renewable Energy field. Numerous solar modules and inverters are mounted on large-scale floating platforms. It is important to design the system so that the inverter operates in its optimum range most of the time. In order to achieve this goal on the DC side, serial and parallel connections of solar modules are used. As a result, the cabling of the PV array architecture is an important issue. Modern electrical installation design requires reducing costs in cabling materials, equipment installation, and maintenance. The reduction of losses and the amount of time required to complete the design are also significant. Therefore, the main topic of this paper is DC cabling in large-scale FPV power plants (>1 ). The serial-parallel (SP) connection scheme of solar modules and the percentage of power loss in DC cables are considered. Furthermore, a general method for determining cable lengths for FPV power plants is defined. The temperature influence on losses in DC cables is analyzed. A new method for determining the current at the maximum power point (MPP) as a function of temperature is proposed. A case study is conducted using a hypothetical 3 MW FPV power plant, and the obtained results are presented and analyzed. - Open Access
- 1 December 2019
- Published by Walter de Gruyter GmbH in B&H Electrical Engineering
- Vol. 13 (1) , 35-43
Design, Development and Implementation of a Distributed Measurement System for No-Load Pressure Measurement in High Voltage Circuit Breakers
This paper presents the design and development of a distributed measurement system for measuring pressure in high voltage circuit breakers (HV CB) and other switching apparatuses, during no-load operations. Instead of using traditional pressure transducers which require significant installation space, additional data acquisition cards and often demand for complex wiring, an in-house solution of pressure measurement is proposed. The system consists of miniature sensors, accompanied with a suitable amplifier, microcontroller unit and communication module, which may be distributed inside the interrupter unit in convenient locations. Due to the fact that the measurement values are transmitted digitally, measurement noise is significantly reduced while the wiring of the system is additionally simplified. The proposed measurement system is tested using two different interrupters (HV CB and a load break switch). The experimental results have demonstrated that the developed system is applicable, accurate, cost-effective, flexible and simple to use.
- 1 December 2019
- Published by Walter de Gruyter GmbH in B&H Electrical Engineering
- Vol. 13 (1) , 35-43
Open AccessDesign, Development and Implementation of a Distributed Measurement System for No-Load Pressure Measurement in High Voltage Circuit Breakers
This paper presents the design and development of a distributed measurement system for measuring pressure in high voltage circuit breakers (HV CB) and other switching apparatuses, during no-load operations. Instead of using traditional pressure transducers which require significant installation space, additional data acquisition cards and often demand for complex wiring, an in-house solution of pressure measurement is proposed. The system consists of miniature sensors, accompanied with a suitable amplifier, microcontroller unit and communication module, which may be distributed inside the interrupter unit in convenient locations. Due to the fact that the measurement values are transmitted digitally, measurement noise is significantly reduced while the wiring of the system is additionally simplified. The proposed measurement system is tested using two different interrupters (HV CB and a load break switch). The experimental results have demonstrated that the developed system is applicable, accurate, cost-effective, flexible and simple to use.
- Open Access
- 1 December 2019
- Published by Walter de Gruyter GmbH in B&H Electrical Engineering
- Vol. 13 (1) , 71-79
A Comprehensive Study of Shape Orientation Methods for Extraction of Phase-Preserving Fourier Descriptors
The magnitude-based Fourier descriptors (FD) are frequently used in shape-based image retrieval, due to their efficiency and effectiveness. Unlike the phase-preserving Fourier descriptors, the magnitude-based Fourier descriptors are inherently invariant under rotation and starting point change, but they discard all valuable information contained in the phase of the Fourier coefficients (FCs). In order to preserve the coefficients’ phase, the orientation and starting point of the shape must be determined. In this paper, we conducted a comprehensive evaluation of different state-of-the-art methods for determining nominal shape orientation, which can be used to extract phase-preserving Fourier descriptors: the point of maximal radius, the axis of least inertia (moments), the phase of the first harmonic, the cross-correlation, the Procrustes distance and the pseudomirror points. The methods were compared in terms of sensitivity to non-rigid transformations, retrieval performance, computational complexity and computational time. The experimental results give insight into the pros and cons of all analyzed methods.
- 1 December 2019
- Published by Walter de Gruyter GmbH in B&H Electrical Engineering
- Vol. 13 (1) , 71-79
Open AccessA Comprehensive Study of Shape Orientation Methods for Extraction of Phase-Preserving Fourier Descriptors
The magnitude-based Fourier descriptors (FD) are frequently used in shape-based image retrieval, due to their efficiency and effectiveness. Unlike the phase-preserving Fourier descriptors, the magnitude-based Fourier descriptors are inherently invariant under rotation and starting point change, but they discard all valuable information contained in the phase of the Fourier coefficients (FCs). In order to preserve the coefficients’ phase, the orientation and starting point of the shape must be determined. In this paper, we conducted a comprehensive evaluation of different state-of-the-art methods for determining nominal shape orientation, which can be used to extract phase-preserving Fourier descriptors: the point of maximal radius, the axis of least inertia (moments), the phase of the first harmonic, the cross-correlation, the Procrustes distance and the pseudomirror points. The methods were compared in terms of sensitivity to non-rigid transformations, retrieval performance, computational complexity and computational time. The experimental results give insight into the pros and cons of all analyzed methods.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 6, 1-6
Alternative pheromone laying strategy — An improvement for the ACO algorithm
This paper gives a brief overview of the current state in the ant colony optimization (ACO) field of study. Furthermore, it introduces an alternative pheromone laying strategy for the ACO algorithm. In the paper, the newly introduced strategy is implemented, tested on a model problem and compared with the classical approach. A parameterized problem space generator has been introduced. The generator generates graphs along which ants are allowed to move freely on the Y axis, but constrained to increment the current value on the X axis by one with each move. In this way, a dynamic decision making optimization problem with the goal of minimizing the path from an arbitrary starting node to an arbitrary finish node has been simulated. Using the ACO algorithm, the generated problems are being solved with the classical pheromone laying approach and the modified approach, introduced in this paper. The obtained results unequivocally indicate that the introduced modification has the potential to serve as an improvement for the ACO algorithm in general.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 6, 1-6
Alternative pheromone laying strategy — An improvement for the ACO algorithm
This paper gives a brief overview of the current state in the ant colony optimization (ACO) field of study. Furthermore, it introduces an alternative pheromone laying strategy for the ACO algorithm. In the paper, the newly introduced strategy is implemented, tested on a model problem and compared with the classical approach. A parameterized problem space generator has been introduced. The generator generates graphs along which ants are allowed to move freely on the Y axis, but constrained to increment the current value on the X axis by one with each move. In this way, a dynamic decision making optimization problem with the goal of minimizing the path from an arbitrary starting node to an arbitrary finish node has been simulated. Using the ACO algorithm, the generated problems are being solved with the classical pheromone laying approach and the modified approach, introduced in this paper. The obtained results unequivocally indicate that the introduced modification has the potential to serve as an improvement for the ACO algorithm in general.
- 1 January 2016
- Published by Elsevier in Signal Processing: Image Communication
- Vol. 40, 82-96
Phase preserving Fourier descriptor for shape-based image retrieval
- 1 January 2016
- Published by Elsevier in Signal Processing: Image Communication
- Vol. 40, 82-96
Phase preserving Fourier descriptor for shape-based image retrieval
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19457871,p. 1-6
Shape description using phase-preserving Fourier descriptor
Contour-based Fourier descriptors are established as a simple and effective shape description method for content-based image retrieval. In order to achieve invariance under rotation and starting point change, most Fourier descriptor implementations disregard the phase of the Fourier coefficients. We introduce a novel method for extracting Fourier descriptors, which preserve the phase of Fourier coefficients and have the desired invariance. We propose specific points, called pseudomirror points, to be used as shape orientation reference. Experimental results indicate that the proposed method significantly outperforms other Fourier descriptor based techniques.
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19457871,p. 1-6
Shape description using phase-preserving Fourier descriptor
Contour-based Fourier descriptors are established as a simple and effective shape description method for content-based image retrieval. In order to achieve invariance under rotation and starting point change, most Fourier descriptor implementations disregard the phase of the Fourier coefficients. We introduce a novel method for extracting Fourier descriptors, which preserve the phase of Fourier coefficients and have the desired invariance. We propose specific points, called pseudomirror points, to be used as shape orientation reference. Experimental results indicate that the proposed method significantly outperforms other Fourier descriptor based techniques.