BTBircan Haspulat Taymaz

Bircan Haspulat Taymaz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Bircan Haspulat Taymaz has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fabrication and Characterization of Wet-Spun Ti3C2Tx MXene Fibers

    by Buket Onat, Bircan Haspulat Taymaz, Volkan Eskizeybek, Handan Kamış

    MXene fibers have attracted considerable attention for flexible electronics and wearable devices owing to their high electrical conductivity and solution processability. The morphology and electrical conductivity of wet-spun MXene fibers are strongly influenced by fabrication conditions. Continuous Ti₃C₂Tₓ MXene fibers were fabricated by wet spinning using colloidal dispersions with concentrations ranging from 25 to 80 mg mL-1. Fiber morphology and electrical conductivity were evaluated as a function of dispersion concentration. The electrical conductivity showed an increasing trend with concentration, reaching 446.06 S cm-1 for fibers prepared from the 80 mg mL-1 dispersion, compared with 58.95 S cm-1 for fibers prepared from the 25 mg mL-1 dispersion. This improvement is attributed to enhanced interflake contact and improved connectivity between MXene nanosheets at higher concentrations. Overall, the results demonstrate the successful fabrication of continuous MXene fibers across a range of dispersion concentrations and clarify the relationship between processing conditions, fiber morphology, and electrical conductivity, providing guidance for the optimization of MXene fiber fabrication for flexible electronic applications.

  • Open Access

    Aloe Vera Extract-Assisted Hydrothermal Synthesis of CuO Nanoparticles for Photocatalytic Degradation of Methylene Blue Dye

    by Aleyna Akıllı, Rıza Turgut Yaman, Ayşenur Özler, Bircan Haspulat Taymaz, Handan Kamış

    Different plant extract-assisted hydrothermal synthesis offers an eco-friendly alternative to traditional approaches for sustainable technological production. Our research explores this environmentally beneficial terrain by presenting copper oxide nanoparticles (CuO NPs) created from Aloe Vera extract. This study contributes to the economical and environmentally friendly green synthesis of CuO NPs by thoroughly investigating synthesis parameters and operating parameters. Using methylene blue (MB) as a model dye, the photocatalytic characteristics of the resulting nanoparticles were examined. The synthesis factors influencing photocatalytic activity efficiency were examined, and the best circumstances were established. When the CuO photocatalyst developed under optimal conditions was used, the degradation efficiency of MB dye was 18.39%, 98.53%, and 83.46% for dark, UV, and visible light, respectively for 90 min reaction time. The influence of catalyst quantity, dye concentration, and reusability on operational parameters was then investigated. This environmentally friendly synthesis process is affordable and simple to utilize for commercial production of CuO NP on a large scale for applications connected to health.

  • Open Access

    Interlayer-engineered free-standing Ti 3 C 2 T X MXene/PDAAQ nanocomposite films for supercapacitor and EMI shielding

    by Aleyna Akıllı Samur, Buket Onat, Bircan Haspulat Taymaz, Volkan Eskizeybek, Handan Kamış

    The rapid expansion of portable and wearable electronics has created a simultaneous demand for materials that can both store energy efficiently and protect devices from electromagnetic interference (EMI). In this context, MXenes have emerged as promising candidates due to their high electrical conductivity and rapid ion transport capability. However, their pronounced restacking tendency significantly restricts accessible surface area and limits overall performance. To address this challenge while introducing multifunctionality, redox-active polydiaminoanthraquinone (PDAAQ) was rationally intercalated into Ti 3 C 2 T X MXene by in situ oxidative polymerization to suppress restacking and accelerate ion transport. Beyond acting as a physical spacer, PDAAQ provides additional pseudocapacitive contribution through quinone-based redox reactions, enhancing the overall charge storage behavior. This present study employs free-standing film architecture, which facilitates continuous electron pathways and improves ion transport without the need for binders or conductive additives. The MXene/PDAAQ free-standing nanocomposite films demonstrated a high specific capacitance of 942.5 F g −1 and excellent cycling stability with 96% retention after 5000 cycles. A solid-state asymmetric supercapacitor was assembled using a PVA/H 2 SO 4 gel electrolyte as both the electrolyte and separator. The device exhibited high volumetric and gravimetric capacitances of 423.177 F cm −3 (406 F g −1 ), respectively, and delivered a volumetric energy density of 30.1 Wh l −1 at a power density of 800 W l −1 . Beyond energy storage, the same dense and well-oriented conductive network provided effective EMI attenuation. The MXene/PDAAQ nanocomposite film had a high electrical conductivity (12.4 × 10 3 S cm −1 ) and achieved 40 dB of shielding effectiveness at 11.2 GHz in the X-band, where reflection of electromagnetic waves by the film was identified as the dominant shielding mechanism. The MXene/PDAAQ system shows promising electrochemical performance as well as effective electromagnetic shielding behavior. Each property was examined individually, indicating its potential for use in next-generation electronic devices.

  • Open Access

    Lightweight and sustainable recycled cellulose based hybrid aerogels with enhanced electromagnetic interference shielding

    by Bircan Haspulat Taymaz, Volkan Eskizeybek

    Developing lightweight, sustainable, high porosity, and high-performance electromagnetic interference (EMI) shielding apparatus is essential to diminish electromagnetic contamination for protecting human health and electronic devices. Herein, 1D carbon nanotubes (CNTs) and 2D graphene nanoplatelets (GNPs) functionalized recycled cellulose aerogel (RCA) were fabricated via a facile method by freeze, solvent exchange, and ambient drying. The effect of nanofiller type and quantity on the structural, morphological, electrical, thermal and EMI shielding performance of the RC-based aerogel were investigated. The as-prepared hybrid aerogel displays the maximum 40.2 dB electromagnetic interference shielding efficiency (SE) at 8.92 dB GHz with absorption dominant characteristic. CNTs:GNPs nanofillers in recycled cellulose matrix provoked conductivity mismatching and increased interfacial polarization loss. At a density of 0.087 gcm−3, CNTs:GNPs; 7:7%wt. doped RCA exhibits a highly specific SE (SSE) value of 461.95 dBcm3g−1 and an absolute SE (SSE/t) value of 2309.29 dBcm2g−1. These results show that the CNTs:GNPs; 7:7%wt. doped RCA can meet practical applications’ lightweight and high-efficiency EMI shielding requirements.


  • Open Access

    Adsorption-Assisted Photocatalytic Degradation of Anionic Direct Yellow-50 and Cationic Methylene Blue Dyes by Chemically Synthesized Poly(1,5-diaminoanthraquinone)

    by Aleyna Akıllı, Ayşenur Özler, Bircan Haspulat Taymaz, Ahmet Hancı, Volkan Eskizeybek, Handan Kamış

    Conducting polymers renowned for their exceptional photocatalytic activity, conductivity, and visible-light absorption capabilities present a compelling alternative for advanced photocatalytic applications. In this regard, the creation of conductive polymers of the next generation has enormous promise for improving energy efficiency as well as solving environmental issues. In this study, the conductive polymer poly(1,5-diaminoanthraquinone) (PDAAQ) with a band gap of 1.28 eV and an electrical conductivity of 1.23 S/cm was successfully synthesized via chemical oxidative polymerization using ammonium peroxydisulfate as an oxidant and perchloric acid as an initiator in an acetonitrile polymerization medium. The adsorption-assisted photocatalytic performance of PDAAQ has been investigated in cationic methylene blue (MB) and an anionic direct yellow (DY) dye under visible irradiation. The effect of polymerization medium, oxidant type, polymerization time, and monomer oxidant ratio on adsorption-assisted photocatalytic degradation of MB was investigated. The synthesized PDAAQ polymer demonstrates exceptional photocatalytic performance, completely degrading MB and DYE dyes under visible light illumination in 6 and 8 min through an adsorption-assisted photocatalysis mechanism. Besides, the photocatalytic dye degradation performance of PDAAQ was investigated for the degradation of synthetic wastewater (SWW) under visible light. The PDAAQ polymer proves to be an effective photocatalyst for photocatalytic applications, showcasing exceptional potential in degrading model dyes and treating synthetic wastewater.


  • Open Access

    Adsorption-Assisted Photocatalytic Degradation of Anionic Direct Yellow-50 and Cationic Methylene Blue Dyes by Chemically Synthesized Poly(1,5-diaminoanthraquinone)

    by Aleyna Akilli, Ayşenur Özler, Bi̇rCan Haspulat Taymaz, Ahmet Hanci, Volkan Eski̇zEybek, Handan Kamiş

    The conductive polymer poly(1,5 diaminoanthraquinone) (PDAAQ) has been synthesized by chemical oxidative polymerization using ammonium peroxydisulfate (APS) as an oxidant and perchloric acid (HClO4) as an initiator in the presence of acetonitrile (ACN) polymerization medium. The characterization of PDAAQ was completed via X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), UV-visible absorbance spectroscopy (UV-vis), scanning electron microscopy (SEM), energy dispersion spectroscopy (EDX), Brunauer–Emmett–Teller analysis (BET) and four-point probe electrical conductivity measurements. PDAAQ with a band gap of 1.28 eV and an electrical conductivity of 1.23 S/cm was successfully synthesized. The adsorption-assisted photocatalytic performance of PDAAQ has been investigated in cationic methylene blue (MB), and an anionic direct yellow (DY) dye under the visible irradiation. For both MB and DY dyes, the reactions were determined to be pseudo-first order equations for the adsorption-assisted photocatalytic process. The effect of polymerization medium, oxidant type, polymerization time and monomer oxidant ratio on adsorption assisted photocatalytic degradation of MB was investigated. The synthesized PDAAQ polymer has excellent photocatalytic performance as a photocatalyst for degradation of MB and DY. 10 µM MB and DY dyes were completely degraded in only 6 and 8 min under visible light illumination using PDAAQ polymer by adsorption-assisted photocatalysis mechanism. Also, the photocatalytic dye degradation performance of PDAAQ was investigated for degradation of synthetic wastewater (SWW) under visible light. PDAAQ polymer can be used as an effective photocatalyst in photocatalytic applications due to its superior and promising performance for the degradation of model dyes and synthetic wastewater.


  • Magnetic and visible light-induced novel green synthesized magnetic Co 3 O 4 photocatalysts via sunflower seed meal extract for anionic and cationic dye removal by adsorption assisted photocatalytic degradation

    by Aleyna Akıllı, Bircan Haspulat Taymaz, Ayşenur Özler, Halime Ak, Ahmet Hancı, Handan Kamış

    This study was aimed at the preparation of m-Co3O4 NPs (magnetic Co3O4 nanoparticles) from sunflower seed meal (SFSM) which is the waste of sunflower seed oil factories, and their application as a photocatalyst for the adsorption assistant photocatalysis degradation of methylene blue (MB), and direct yellow-50 (DY-50) under the visible irradiations. Also, the photocatalytic performance of m-Co3O4 NPs was evaluated in synthetic wastewater. The produced m-Co3O4 NPs were ferromagnetic with a saturation magnetization value of 4.3 emu g-1 and the degradation of cationic MB and anionic DY-50 dyes by 100% and 93% in 20 min and 35 min, respectively, by adsorption-assisted photocatalytic process under visible light was achieved. The reactions were found to be pseudo-second-order equation for the adsorption-assisted photocatalytic process for both dyes. The photocatalytic activity of m-Co3O4 NPs decreased slightly even after five repeated cycles. These results show that the m-Co3O4 NPs can be used successfully in dye treatment in wastewater with their adsorption-assisted photocatalytic properties, activation by visible light, magnetic separability, and low-cost production.