Emila M. Živković
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Emila M. Živković has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Mirjana Lj. Kijevcanin
Faculty of Technology and Metallurgy, University of Belgrade, 11000 Belgrade, Serbia
29 shared publications - Divna M. Majstorović
University of Belgrade, Faculty of Technology and Metallurgy, Belgrade, Serbia
22 shared publications Slobodan P. Šerbanović
University of Belgrade, Faculty of Technology and Metallurgy, Karnegijeva 4, 11120 Belgrade, Serbia
14 shared publications- Ivona R. Radović
Faculty of Technology and Metallurgy, University of Belgrade, 11000 Belgrade, Serbia
7 shared publications - Nikola Živković
Department of Thermal Engineering and Energy, “VINČA” Institute of Nuclear Sciences-National Institute of the Republic of Serbia, University of Belgrade, Mike Petrovića Alasa 12-14, 11351 Vinča, 11001 Belgrade, Serbia
6 shared publications Bojan D. Djordjević
4 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by National Library of Serbia
- Vol. 80 (1) , 51-59
Thermal conductivity measurements of liquids: Challenges and a novel solution
This paper provides a concise and accessible overview of commonly used methods for measuring the thermal conductivity of liquids. Both steady-state and transient techniques are briefly outlined, including guarded hot plate methods, laser flash analysis, and approaches based on time-dependent thermal response. Particular focus is placed on the transient hot wire method, recognized for its simplicity, versatility, and its proven suitability for liquid samples. In addition, a recently developed patented approach based on the transient hot wire technique is presented in a more illustrative manner. The concept relies on improvements in sensor design and data interpretation, aimed at enhancing measurement stability and reducing typical sources of error in liquid measurements. Rather than a detailed technical validation, the emphasis is on explaining the idea and its potential benefits in practical applications.
- 1 January 2026
- Published by National Library of Serbia
- Vol. 80 (1) , 51-59
Open AccessThermal conductivity measurements of liquids: Challenges and a novel solution
This paper provides a concise and accessible overview of commonly used methods for measuring the thermal conductivity of liquids. Both steady-state and transient techniques are briefly outlined, including guarded hot plate methods, laser flash analysis, and approaches based on time-dependent thermal response. Particular focus is placed on the transient hot wire method, recognized for its simplicity, versatility, and its proven suitability for liquid samples. In addition, a recently developed patented approach based on the transient hot wire technique is presented in a more illustrative manner. The concept relies on improvements in sensor design and data interpretation, aimed at enhancing measurement stability and reducing typical sources of error in liquid measurements. Rather than a detailed technical validation, the emphasis is on explaining the idea and its potential benefits in practical applications.
- 5 August 2025
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 600
Viscosity of biodiesel: experiments and modeling
- 5 August 2025
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 600
Viscosity of biodiesel: experiments and modeling
- Open Access
- 22 June 2024
- Published by Union of Mechanical and Electrotechnical Engineers and Technicians of Serbia (SMEITS)
- Vol. 37 (1) , 167-176
Densities and viscosities of binary systems with N,N-Dimethylaniline and Tetra Ethylene Glycol Dimethyl Ether or N-Methyl-2-Pyrrolidone, as potential solvents for flue gas desulphurization processes
Sulfur oxides are emitted as one of the products in the process of combusting solid fossil fuels in thermal power plants, especially the Kolubara and Kostolac lignites in the Republic of Serbia. In order to reduce the emission level of the indirect Greenhouse gases (GHG) from sta-tionary sources, it is inevitable to implement flue gas desulfurization (FGD) technology. In addi-tion to the classic limestone process, technological procedures based on the physical or chemical absorption of sulfur oxides in the solvent and its thermal regeneration are becoming increasingly common. In order to properly design and optimize the process, it is significant to precisely deter-mine the thermophysical properties of pure components and their mixtures. The paper presents the results of determining the density and viscosity of two binary mix-tures, N,N-Dimethylaniline (N,N-DMA) + Tetra Ethylene Glycol Dimethyl Ether (TEGDME) and N,N-Dimethylaniline (N,N-DMA) + N-methyl-2-pyrrolidone (NMP). Measurements were made using a densitometer Anton Paar DMA 5000 and Stabinger viscometer Anton Paar SVM 3000/G2, at atmospheric pressure. The obtained experimental results are presented as a function of temper-ature and N,N-DMA mole fraction. N,N-DMA belongs to the group of amines, and it has been used as a sorbent for purification of flue gases in processes with thermal regeneration (CANSOLV, Sulphidine and ASARCO pro-cesses). The other two organic solvents are TEGDME and NMP. Special attention was paid to NMP due to its low cost and low viscosity, with its favorable properties, making it competitive as a solvent for FGD. TEGDME is a polar solvent, but it is not selective to SO2 and other gaseous components, so NMP has been suggested as an alternative solution. A regenerative process for SO2 removal, with TEGDME, has already found commercial application (Solinox process). NMP is already industrially used as a solvent in Lurgi's Purisol process, due to its nature for selective desulfurization of flue gases.
- 22 June 2024
- Published by Union of Mechanical and Electrotechnical Engineers and Technicians of Serbia (SMEITS)
- Vol. 37 (1) , 167-176
Open AccessDensities and viscosities of binary systems with N,N-Dimethylaniline and Tetra Ethylene Glycol Dimethyl Ether or N-Methyl-2-Pyrrolidone, as potential solvents for flue gas desulphurization processes
Sulfur oxides are emitted as one of the products in the process of combusting solid fossil fuels in thermal power plants, especially the Kolubara and Kostolac lignites in the Republic of Serbia. In order to reduce the emission level of the indirect Greenhouse gases (GHG) from sta-tionary sources, it is inevitable to implement flue gas desulfurization (FGD) technology. In addi-tion to the classic limestone process, technological procedures based on the physical or chemical absorption of sulfur oxides in the solvent and its thermal regeneration are becoming increasingly common. In order to properly design and optimize the process, it is significant to precisely deter-mine the thermophysical properties of pure components and their mixtures. The paper presents the results of determining the density and viscosity of two binary mix-tures, N,N-Dimethylaniline (N,N-DMA) + Tetra Ethylene Glycol Dimethyl Ether (TEGDME) and N,N-Dimethylaniline (N,N-DMA) + N-methyl-2-pyrrolidone (NMP). Measurements were made using a densitometer Anton Paar DMA 5000 and Stabinger viscometer Anton Paar SVM 3000/G2, at atmospheric pressure. The obtained experimental results are presented as a function of temper-ature and N,N-DMA mole fraction. N,N-DMA belongs to the group of amines, and it has been used as a sorbent for purification of flue gases in processes with thermal regeneration (CANSOLV, Sulphidine and ASARCO pro-cesses). The other two organic solvents are TEGDME and NMP. Special attention was paid to NMP due to its low cost and low viscosity, with its favorable properties, making it competitive as a solvent for FGD. TEGDME is a polar solvent, but it is not selective to SO2 and other gaseous components, so NMP has been suggested as an alternative solution. A regenerative process for SO2 removal, with TEGDME, has already found commercial application (Solinox process). NMP is already industrially used as a solvent in Lurgi's Purisol process, due to its nature for selective desulfurization of flue gases.
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Hemijska industrija
- Vol. 78 (2) , 105-111
Nanofluids: Why we love them?
The rising need for fluids with significantly improved heat transfer properties led to the development of nanofluids. The first experiments showed encouraging results reflected in increased thermal conductivity and heat transfer coefficient accompanied with better stability than colloid suspension. Many research laboratories and companies observed the potential of nanofluid technology for specific industrial applications. However, after publication of numerous papers with contradictory results for the same or similar nanofluids, many issues arose. Although in some branches of industry nanofluids have already found practical applications, at some point researchers went back to basics, conducting extended studies and benchmark tests in attempt to explain the nanoparticle influence on thermophysical properties of nanofluids. The final goal of the whole scientific community is to produce nanofluids at low cost, exhibiting long-term stability, and good fluidity as the three most significant preconditions toward practical applications in the heat transport field.
- 1 January 2024
- Published by National Library of Serbia in Hemijska industrija
- Vol. 78 (2) , 105-111
Open AccessNanofluids: Why we love them?
The rising need for fluids with significantly improved heat transfer properties led to the development of nanofluids. The first experiments showed encouraging results reflected in increased thermal conductivity and heat transfer coefficient accompanied with better stability than colloid suspension. Many research laboratories and companies observed the potential of nanofluid technology for specific industrial applications. However, after publication of numerous papers with contradictory results for the same or similar nanofluids, many issues arose. Although in some branches of industry nanofluids have already found practical applications, at some point researchers went back to basics, conducting extended studies and benchmark tests in attempt to explain the nanoparticle influence on thermophysical properties of nanofluids. The final goal of the whole scientific community is to produce nanofluids at low cost, exhibiting long-term stability, and good fluidity as the three most significant preconditions toward practical applications in the heat transport field.
- 25 August 2023
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 389
A new setup for speed of sound measurements and experimental data for nanofluids Al2O3 or Ag with water or ethylene glycol
- 25 August 2023
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 389
A new setup for speed of sound measurements and experimental data for nanofluids Al2O3 or Ag with water or ethylene glycol
- 5 July 2022
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 67 (9) , 2257-2273
Volumetric and Transport Properties of Isoamyl Acetate Based Binary Systems─Experimental Determination and Modeling
- 5 July 2022
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 67 (9) , 2257-2273
Volumetric and Transport Properties of Isoamyl Acetate Based Binary Systems─Experimental Determination and Modeling
- Open Access
- 1 January 2022
- Published by National Library of Serbia in Thermal Science
- Vol. 26 (1 Part A) , 319-328
Gravimetric and instrumental methods comparison for experimental determination of carbonate carbon content in solid mineral fuels
The content of combustible elements in solid mineral fuels (carbon, hydrogen, etc.) are very important, since they most directly affect the heat value. It should be noted that the fuel heat value depends on many other constituents, such as ash and moisture. In this paper, special attention has been paid to carbon content. In solid mineral fuels, carbon is found alone or bound in the form of various compounds. One of them is mineral carbonate compounds bound as carbonate carbon, which originates from absorbed CO2 from atmosphere. Determination of carbonate carbon content of solid mineral fuels was performed by standard gravimetric method (according to ISO 925: 2019), and newly developed instrumental method, using thermogravimetric analyzer LECO TGA 701. Comparison of obtained experimental results was done. Four types of coal, Kolubara lignite, Kostolac lignite, brown coal, and control coal sample were included in experimental analysis. In addition, moisture in the samples was also determined using analytical method and inspected using LECO TGA 701 thermogravimetric analyzer, as well as total carbon content using the LECO CHN 628 elemental analyzer. An analysis and comparison of the obtained results was performed, and comments and conclusions are presented. The experiments were done in the department for fuel characterization, Laboratory for Thermal Engineering and Energy, Institute of Nuclear Sciences Vinca.
- 1 January 2022
- Published by National Library of Serbia in Thermal Science
- Vol. 26 (1 Part A) , 319-328
Open AccessGravimetric and instrumental methods comparison for experimental determination of carbonate carbon content in solid mineral fuels
The content of combustible elements in solid mineral fuels (carbon, hydrogen, etc.) are very important, since they most directly affect the heat value. It should be noted that the fuel heat value depends on many other constituents, such as ash and moisture. In this paper, special attention has been paid to carbon content. In solid mineral fuels, carbon is found alone or bound in the form of various compounds. One of them is mineral carbonate compounds bound as carbonate carbon, which originates from absorbed CO2 from atmosphere. Determination of carbonate carbon content of solid mineral fuels was performed by standard gravimetric method (according to ISO 925: 2019), and newly developed instrumental method, using thermogravimetric analyzer LECO TGA 701. Comparison of obtained experimental results was done. Four types of coal, Kolubara lignite, Kostolac lignite, brown coal, and control coal sample were included in experimental analysis. In addition, moisture in the samples was also determined using analytical method and inspected using LECO TGA 701 thermogravimetric analyzer, as well as total carbon content using the LECO CHN 628 elemental analyzer. An analysis and comparison of the obtained results was performed, and comments and conclusions are presented. The experiments were done in the department for fuel characterization, Laboratory for Thermal Engineering and Energy, Institute of Nuclear Sciences Vinca.
- 20 May 2020
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 65 (6) , 3044-3062
Volumetric and Viscometric Study of 1-Hexanol-Based Binary Systems: Experimental Determination and Modeling
- 20 May 2020
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 65 (6) , 3044-3062
Volumetric and Viscometric Study of 1-Hexanol-Based Binary Systems: Experimental Determination and Modeling
- Open Access
- 1 January 2020
- Published by National Library of Serbia in Hemijska industrija
- Vol. 74 (3) , 163-185
Analysis of thermophysical properties of binary systems containing ethyl acetate and 1-propanol or 1-butanol
The aim of this research is the experimental determination of density, viscosity, refractive index and speed of sound for binary mixtures of the ester ethyl acetate and alcohols. Experimental measurements were carried out for two systems with 1-propanol and 1-butanol at atmospheric pressure and in a temperature range 288.15 - 323.15 K. Results of experimental measurements were further used to determine excess molar volumes, viscosity deviations, refractive index deviations, and excess isentropic compressibility for each investigated mixture. These calculated data were correlated using the empirical Redlich-Kister equation. Positive values of the excess molar volume and isentropic compressibility appear for both analysed systems, while values of viscosity and refractive index deviations are negative. The structure and specific characteristics of different molecules in considered mixtures and determined non-ideal behaviour allow the insight into the possible type of interactions in the mixture, interstitial accommodation and structural effects.
- 1 January 2020
- Published by National Library of Serbia in Hemijska industrija
- Vol. 74 (3) , 163-185
Open AccessAnalysis of thermophysical properties of binary systems containing ethyl acetate and 1-propanol or 1-butanol
The aim of this research is the experimental determination of density, viscosity, refractive index and speed of sound for binary mixtures of the ester ethyl acetate and alcohols. Experimental measurements were carried out for two systems with 1-propanol and 1-butanol at atmospheric pressure and in a temperature range 288.15 - 323.15 K. Results of experimental measurements were further used to determine excess molar volumes, viscosity deviations, refractive index deviations, and excess isentropic compressibility for each investigated mixture. These calculated data were correlated using the empirical Redlich-Kister equation. Positive values of the excess molar volume and isentropic compressibility appear for both analysed systems, while values of viscosity and refractive index deviations are negative. The structure and specific characteristics of different molecules in considered mixtures and determined non-ideal behaviour allow the insight into the possible type of interactions in the mixture, interstitial accommodation and structural effects.
- Open Access
- 1 January 2020
- Published by National Library of Serbia in Hemijska industrija
- Vol. 74 (2) , 75-76
The role of science in modern society
- 1 January 2020
- Published by National Library of Serbia in Hemijska industrija
- Vol. 74 (2) , 75-76
Open AccessThe role of science in modern society