Andrzej Gruchot
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrzej Gruchot has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Tymoteusz Zydroń
DSc., PhD., Eng., University of Agriculture in Krakow, al. Mickiewicza 21, 31-120 Cracow, Poland
13 shared publications Eugeniusz Zawisza
University of Agriculture in Kraków, Faculty of Environmental Engineering and Geodesy, Department of Hydraulic Engineering and Geotechnics, 24/28 Adama Mickiewicza Avenue, 30-059 Kraków, Poland
12 shared publicationsTymoteusz Zydroń
University of Agriculture in Kraków, Faculty of Environmental Engineering and Geodesy, Department of Hydraulic Engineering and Geotechnics, 24/28 Adama Mickiewicza Avenue, 30-059 Kraków, Poland
5 shared publications- Jacek Stanisz
Mineral and Energy Economy Research Institute, Polish Academy of Science, Józefa Wybickiego 7 A, 31-261 Kraków, Poland
4 shared publications - Zbyněk Zachoval
Faculty of Civil Engineering, Brno University of Technology, Veveří street 331/95, 602 00 Brno
4 shared publications Brno University of Technology
3 shared publications
Latest Publications
- Open Access
- 12 June 2026
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 74 (4) , e158781
The influence of the addition of crumb tire rubber on the shear strength parameters of colliery spoil
The article presents the results of research on the influence of a crumb rubber additive on the mechanical properties of a colliery spoils composite. The analysis covered compaction parameters (optimum moisture content, maximum dry density of solid particles) and shear strength parameters (angle of internal friction, cohesion) for composites containing 5%, 10%, and 20% crumb rubber. Compaction parameters were determined using the Proctor apparatus at a compaction energy of 0.59 J·cm−3 . Shear strength parameters were measured in a direct shear apparatus on samples with a cross-sectional dimension of 12×12 cm and a height of 2.9 cm. Soil samples were sheared with and without water saturation at a rate of 0.1 mm·min−1 until 15% horizontal deformation was achieved. The results indicate that the addition of crumb rubber decreases the maximum dry density of solid particles and increases the optimum moisture content, thereby impairing the material compactibility. For shear strength, complex relationships were observed: a small addition of crumb rubber (5–10%) improves cohesion by up to 30%, while a higher content (20%) significantly reduces it, along with the angle of internal friction. Water saturation of the samples further decreases the strength parameters, particularly with large crumb rubber additions. The optimal crumb rubber addition ranged from 5 to 10%, yielding the best values of the angle of internal friction and cohesion. The research results highlight the high potential for using colliery spoils composites with crumb rubber in earthworks, provided that the component proportions are appropriately selected.
- 12 June 2026
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 74 (4) , e158781
Open AccessThe influence of the addition of crumb tire rubber on the shear strength parameters of colliery spoil
The article presents the results of research on the influence of a crumb rubber additive on the mechanical properties of a colliery spoils composite. The analysis covered compaction parameters (optimum moisture content, maximum dry density of solid particles) and shear strength parameters (angle of internal friction, cohesion) for composites containing 5%, 10%, and 20% crumb rubber. Compaction parameters were determined using the Proctor apparatus at a compaction energy of 0.59 J·cm−3 . Shear strength parameters were measured in a direct shear apparatus on samples with a cross-sectional dimension of 12×12 cm and a height of 2.9 cm. Soil samples were sheared with and without water saturation at a rate of 0.1 mm·min−1 until 15% horizontal deformation was achieved. The results indicate that the addition of crumb rubber decreases the maximum dry density of solid particles and increases the optimum moisture content, thereby impairing the material compactibility. For shear strength, complex relationships were observed: a small addition of crumb rubber (5–10%) improves cohesion by up to 30%, while a higher content (20%) significantly reduces it, along with the angle of internal friction. Water saturation of the samples further decreases the strength parameters, particularly with large crumb rubber additions. The optimal crumb rubber addition ranged from 5 to 10%, yielding the best values of the angle of internal friction and cohesion. The research results highlight the high potential for using colliery spoils composites with crumb rubber in earthworks, provided that the component proportions are appropriately selected.
- 27 February 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- p. 535
Modeling of root reinforcement of European hornbeam considering the use different fiber bundle models
This study comprises measurements of root systems of European hornbeam in forests located near Winiary, in the vicinity of Gdów (Wiśnickie Foothills, Poland) and near the town of Kanice (Moravia, Czech Republic). Field research included root measurements using the trench wall method conducted at a distance of approximately 1 m from the tree trunks. Tensile strength of the roots collected from both study sites and the geotechnical properties of the soil were determined in the laboratory. Based on the results of field measurements and laboratory tests, the root reinforcement was calculated using selected fibre bundle models. This study was aimed to compare root systems and mechanical properties of roots of the European hornbeam from the two sites and to compare the root reinforcement results obtained using different bundle models, taking into account different approaches to load distribution. The paper also discusses the impact of the tensile strength-strain characteristics of roots and their orientation relative to the direction of slip plane (zone) on the root reinforcement. The results of laboratory tests showed that tensile strength and elasticity of roots collected from both sites are very similar. Calculations showed that the values of root reinforcement computed using fiber bundle models are even 2.5 times smaller than those obtained from the classic Wu–Waldron model. On the other hand, the calculation results between fiber bundle models can differ by more than 2 times. It was also shown that the force-strain relationship used for calculation of root reinforcement has a significant impact on the results of the analyses, and the use of a bilinear force-strain relationship provides the results higher by approximately 10–13%.
- 27 February 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- p. 535
Modeling of root reinforcement of European hornbeam considering the use different fiber bundle models
This study comprises measurements of root systems of European hornbeam in forests located near Winiary, in the vicinity of Gdów (Wiśnickie Foothills, Poland) and near the town of Kanice (Moravia, Czech Republic). Field research included root measurements using the trench wall method conducted at a distance of approximately 1 m from the tree trunks. Tensile strength of the roots collected from both study sites and the geotechnical properties of the soil were determined in the laboratory. Based on the results of field measurements and laboratory tests, the root reinforcement was calculated using selected fibre bundle models. This study was aimed to compare root systems and mechanical properties of roots of the European hornbeam from the two sites and to compare the root reinforcement results obtained using different bundle models, taking into account different approaches to load distribution. The paper also discusses the impact of the tensile strength-strain characteristics of roots and their orientation relative to the direction of slip plane (zone) on the root reinforcement. The results of laboratory tests showed that tensile strength and elasticity of roots collected from both sites are very similar. Calculations showed that the values of root reinforcement computed using fiber bundle models are even 2.5 times smaller than those obtained from the classic Wu–Waldron model. On the other hand, the calculation results between fiber bundle models can differ by more than 2 times. It was also shown that the force-strain relationship used for calculation of root reinforcement has a significant impact on the results of the analyses, and the use of a bilinear force-strain relationship provides the results higher by approximately 10–13%.
- 1 June 2025
- Published by Silesian University of Technology in Scientific Journal of Silesian University of Technology. Series Transport
- Vol. 127, 103-128
ASSESSMENT OF THE ACOUSTIC CLIMATE ON THE EXAMPLE OF THE ROAD IN MICHAŁOWICE (POLAND)
The aim of the research was to assess the acoustic climate along the DK7 national road in Michałowice (Kraków district, Poland). The climate assessment was carried out during the period from September to May at two measurement sites located at a distance of 11.5 and 27.0 m from the road. The scope of the study included measuring the intensity of noise, recording the number of light and heavy vehicles, measuring the temperature of as well as air and the type of precipitation. The results of noise intensity measurements showed numerous cases of exceeding the permissible equivalent noise level for single-family housing areas. The machine learning methods used showed that the noise level was influenced by air temperature, snowfall, and plant vegetation. Significantly lower values of the equivalent noise level were obtained on weekends, indicating that commercial road traffic prevailed in the analyzed road section.
- 1 June 2025
- Published by Silesian University of Technology in Scientific Journal of Silesian University of Technology. Series Transport
- Vol. 127, 103-128
ASSESSMENT OF THE ACOUSTIC CLIMATE ON THE EXAMPLE OF THE ROAD IN MICHAŁOWICE (POLAND)
The aim of the research was to assess the acoustic climate along the DK7 national road in Michałowice (Kraków district, Poland). The climate assessment was carried out during the period from September to May at two measurement sites located at a distance of 11.5 and 27.0 m from the road. The scope of the study included measuring the intensity of noise, recording the number of light and heavy vehicles, measuring the temperature of as well as air and the type of precipitation. The results of noise intensity measurements showed numerous cases of exceeding the permissible equivalent noise level for single-family housing areas. The machine learning methods used showed that the noise level was influenced by air temperature, snowfall, and plant vegetation. Significantly lower values of the equivalent noise level were obtained on weekends, indicating that commercial road traffic prevailed in the analyzed road section.
- Open Access
The Effects of Lime and Cement Addition on the Compaction and Shear Strength Parameters of Silty Soils
This article presents the results of laboratory tests of compaction parameters and shear strength of silty soils with and without the addition of hydraulic binder in the form of lime and/or cement. The tests were carried out on samples formed with an optimum moisture content and with 0, 3, 5, and 8% hydraulic binder added to the dry mass of the soil. The soil samples were examined after 7 and 14 days of air–water treatment without and with freeze–thaw cycles. It was found that the addition of lime and cement caused changes in the compaction parameters. This effect depended to a large extent on the type of binder, and also on the grain size composition of the tested soil. The tests showed that the shear strength and the parameters describing it, i.e., the angle of internal friction and cohesion, were high and largely depended on the type of binder and the sample treatment method, as well as its duration. The obtained results indicate that the use of hydraulic binders was an effective method of surface stabilization. Improving soil properties based on the addition of a hydraulic binder is a beneficial method for the environment from the viewpoint of sustainable development and reducing CO2 emissions because it does not require the use of, e.g., soil replacement. Using the SHAP algorithm, it was found that normal stress, initial moisture content, and curing time of the samples were the main input features that influenced the shear strength.
Open AccessThe Effects of Lime and Cement Addition on the Compaction and Shear Strength Parameters of Silty Soils
This article presents the results of laboratory tests of compaction parameters and shear strength of silty soils with and without the addition of hydraulic binder in the form of lime and/or cement. The tests were carried out on samples formed with an optimum moisture content and with 0, 3, 5, and 8% hydraulic binder added to the dry mass of the soil. The soil samples were examined after 7 and 14 days of air–water treatment without and with freeze–thaw cycles. It was found that the addition of lime and cement caused changes in the compaction parameters. This effect depended to a large extent on the type of binder, and also on the grain size composition of the tested soil. The tests showed that the shear strength and the parameters describing it, i.e., the angle of internal friction and cohesion, were high and largely depended on the type of binder and the sample treatment method, as well as its duration. The obtained results indicate that the use of hydraulic binders was an effective method of surface stabilization. Improving soil properties based on the addition of a hydraulic binder is a beneficial method for the environment from the viewpoint of sustainable development and reducing CO2 emissions because it does not require the use of, e.g., soil replacement. Using the SHAP algorithm, it was found that normal stress, initial moisture content, and curing time of the samples were the main input features that influenced the shear strength.
- Open Access
- 29 October 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (21) , 9403
Water Permeability of Kemafil Georopes with a Geotextile Core Made of Wool Waste Based on Laboratory and Field Tests
This paper presents the results of laboratory and field tests on the hydraulic properties of georopes produced using the Kemafil technology from sheep wool waste generated in the textile industry. The laboratory tests included the determination of the basic physical parameters and filtration properties of georopes, as well as tests of the physical properties and water permeability of the experimental training ground. As part of the field research, measurements of water infiltration through 1.0, 2.0 and 5.0 m long georopes embedded in the ground were carried out in nine monthly cycles. The conditions of water flow through the georopes were monitored on the basis of georope resistance measurements. Numerical calculations were also performed to determine the conditions of water flow through the georopes and the process of water infiltration from the georopes into the ground. The laboratory tests have shown that the water permeability of georopes is high and, based on the filtration criteria, they can act as a drainage material. The field measurements showed that the resistance of the georopes changed over time and depended on the amount of water supplied and the absorbency of the ground. The results of the numerical calculations were consistent with the results of the field measurements, at the same time indicating that some water infiltrated into the ground in the vicinity of the georopes, meaning that under the conditions that prevailed during the experiment, the georopes can act as infiltration drainage systems in the ground.
- 29 October 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (21) , 9403
Open AccessWater Permeability of Kemafil Georopes with a Geotextile Core Made of Wool Waste Based on Laboratory and Field Tests
This paper presents the results of laboratory and field tests on the hydraulic properties of georopes produced using the Kemafil technology from sheep wool waste generated in the textile industry. The laboratory tests included the determination of the basic physical parameters and filtration properties of georopes, as well as tests of the physical properties and water permeability of the experimental training ground. As part of the field research, measurements of water infiltration through 1.0, 2.0 and 5.0 m long georopes embedded in the ground were carried out in nine monthly cycles. The conditions of water flow through the georopes were monitored on the basis of georope resistance measurements. Numerical calculations were also performed to determine the conditions of water flow through the georopes and the process of water infiltration from the georopes into the ground. The laboratory tests have shown that the water permeability of georopes is high and, based on the filtration criteria, they can act as a drainage material. The field measurements showed that the resistance of the georopes changed over time and depended on the amount of water supplied and the absorbency of the ground. The results of the numerical calculations were consistent with the results of the field measurements, at the same time indicating that some water infiltrated into the ground in the vicinity of the georopes, meaning that under the conditions that prevailed during the experiment, the georopes can act as infiltration drainage systems in the ground.
- Open Access
- 30 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 70 (3) , 325-341
Effect of polypropylene fibres on the shear strength of fine-grained soil
This paper presents the results of shear strength tests of fine-grained soil reinforced by randomly oriented fibres. The tests were carried out in a direct shear apparatus on samples with a diameter of 100 mm and a height of 20 mm. The samples were formed directly in the apparatus box at a natural moisture content and two values of the degree of compaction (IS = 0:79 and 0.90). The studies were carried out for samples of natural moisture content and for soaked ones. The two types of polypropylene fibres were used: monofilament and fibrillated (of traded names Fibermesh 300-e3 and SikaCem Fiber-12, respectively). The fibre content was 0.25; 0.50 and 1.00% by the weight of the dry soil. The results showed that the presence of fibre within the soil increased its the shear strength. The improvement of the shear strength was related to the type of reinforcement, its content and the soil parameters. The maximum increase in shear strength was 47% compared to the shear strength of the unreinforced soil. The increase in shear strength values were related mainly to the increase in the angle of internal friction of the soil. It was found that as the degree of compaction of the soil increases, the higher enhance of the shear strength of reinforced soil occurs. It was also found that the improvement of shear strength of reinforced soaked samples was more significant than for un-soaked ones.
- 30 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 70 (3) , 325-341
Open AccessEffect of polypropylene fibres on the shear strength of fine-grained soil
This paper presents the results of shear strength tests of fine-grained soil reinforced by randomly oriented fibres. The tests were carried out in a direct shear apparatus on samples with a diameter of 100 mm and a height of 20 mm. The samples were formed directly in the apparatus box at a natural moisture content and two values of the degree of compaction (IS = 0:79 and 0.90). The studies were carried out for samples of natural moisture content and for soaked ones. The two types of polypropylene fibres were used: monofilament and fibrillated (of traded names Fibermesh 300-e3 and SikaCem Fiber-12, respectively). The fibre content was 0.25; 0.50 and 1.00% by the weight of the dry soil. The results showed that the presence of fibre within the soil increased its the shear strength. The improvement of the shear strength was related to the type of reinforcement, its content and the soil parameters. The maximum increase in shear strength was 47% compared to the shear strength of the unreinforced soil. The increase in shear strength values were related mainly to the increase in the angle of internal friction of the soil. It was found that as the degree of compaction of the soil increases, the higher enhance of the shear strength of reinforced soil occurs. It was also found that the improvement of shear strength of reinforced soaked samples was more significant than for un-soaked ones.
- Open Access
- 18 June 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 70 (2) , 97-117
Effect of shear rate and saturation on shear strength of mineral and anthropogenic soil
The aim of the study was to determine the shear strength of mineral and anthropogenic soil of similar grain size as a function of the applied shear rate and water saturation. Stability calculations using the finite element method of the road embankment model were also carried out to demonstrate the variation in factor of safety values depending on the adopted values of the angle of internal friction and cohesion. The tests were carried out in a direct shear apparatus in a 100 x 100 mm box with a sample height of 20.5 mm. The samples were formed directly in the apparatus box at optimum moisture content until a compaction index of IS = 1.00 was obtained. Tests were carried out under conditions without and with water saturation at shear rates of 0.01, 0.05, 0.1, 0.5 and 1.0 mm•min–1 until 18% horizontal displacement was achieved. The results showed that the effect of shear rate on the strength parameters was not unequivocal and was much smaller than the changes caused by saturation of samples. An increase in shear rate resulted in small changes in the angle of internal friction with a tendency towards a decrease. In contrast, cohesion varied over a much larger range with increasing shear rate, with an apparent initial decrease and subsequent increase. The saturation of the samples resulted in a decrease in the angle of internal friction of the cohesive soil and an increase for the ash-slag mixture. The cohesion of both soils decreased. The results obtained from the road embankment model stability calculations confirmed that soil saturation had a greater influence on the factor of safety values obtained than the shear rate.
- 18 June 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 70 (2) , 97-117
Open AccessEffect of shear rate and saturation on shear strength of mineral and anthropogenic soil
The aim of the study was to determine the shear strength of mineral and anthropogenic soil of similar grain size as a function of the applied shear rate and water saturation. Stability calculations using the finite element method of the road embankment model were also carried out to demonstrate the variation in factor of safety values depending on the adopted values of the angle of internal friction and cohesion. The tests were carried out in a direct shear apparatus in a 100 x 100 mm box with a sample height of 20.5 mm. The samples were formed directly in the apparatus box at optimum moisture content until a compaction index of IS = 1.00 was obtained. Tests were carried out under conditions without and with water saturation at shear rates of 0.01, 0.05, 0.1, 0.5 and 1.0 mm•min–1 until 18% horizontal displacement was achieved. The results showed that the effect of shear rate on the strength parameters was not unequivocal and was much smaller than the changes caused by saturation of samples. An increase in shear rate resulted in small changes in the angle of internal friction with a tendency towards a decrease. In contrast, cohesion varied over a much larger range with increasing shear rate, with an apparent initial decrease and subsequent increase. The saturation of the samples resulted in a decrease in the angle of internal friction of the cohesive soil and an increase for the ash-slag mixture. The cohesion of both soils decreased. The results obtained from the road embankment model stability calculations confirmed that soil saturation had a greater influence on the factor of safety values obtained than the shear rate.
- 1 November 2022
- Published by The University of Agriculture in Krakow in Acta Scientiarum Polonorum. Formatio Circumiectus
- Vol. 21 (2) , 17-33
SUFOSION PHENOMENA IN THE AREA OF PIENINY NATIONAL PARK
Aim of the study: The aim of the study was to determine the range and conditions for the formation of the piping hole and the piping canal found in the Pieniny National Park in May 2019. Material and methods: The scope of the research carried out included the determination of the geotechnical characteristics of subsoil on the slope near the piping hole and along the piping canal. Numerical calculations with the finite element method were also carried out in the GeoStudio program, which allowed to assess the possibilities of soil deformation caused by the seepage forces. Results and conclusions: The results of the research and the analysis of the literature showed that the piping processes in the Polish Carpathians are a common phenomenon that plays a sculptural role. The observed piping form indicates that on the slope is a continuous, several dozen meters long, piping channel formed in medium-cohesive, clay-dusty soils. It should be expected that during periods of prolonged or intense rainfall such phenomena will intensify. The calculation results did not confirm the occurrence of conditions favoring the formation of hydraulic deformations. However, during the increased filtration flow, high values of the hydraulic gradient in the soil are generated, which, in the case of high porosity of the soil, favors the removal of soil particles. The occurring process of piping on the slope in question is favored by the presence of a wooden through from which water infiltrates the ground, which increases the intensity of in-soil flow in the analyzed part of the slope.
- 1 November 2022
- Published by The University of Agriculture in Krakow in Acta Scientiarum Polonorum. Formatio Circumiectus
- Vol. 21 (2) , 17-33
SUFOSION PHENOMENA IN THE AREA OF PIENINY NATIONAL PARK
Aim of the study: The aim of the study was to determine the range and conditions for the formation of the piping hole and the piping canal found in the Pieniny National Park in May 2019. Material and methods: The scope of the research carried out included the determination of the geotechnical characteristics of subsoil on the slope near the piping hole and along the piping canal. Numerical calculations with the finite element method were also carried out in the GeoStudio program, which allowed to assess the possibilities of soil deformation caused by the seepage forces. Results and conclusions: The results of the research and the analysis of the literature showed that the piping processes in the Polish Carpathians are a common phenomenon that plays a sculptural role. The observed piping form indicates that on the slope is a continuous, several dozen meters long, piping channel formed in medium-cohesive, clay-dusty soils. It should be expected that during periods of prolonged or intense rainfall such phenomena will intensify. The calculation results did not confirm the occurrence of conditions favoring the formation of hydraulic deformations. However, during the increased filtration flow, high values of the hydraulic gradient in the soil are generated, which, in the case of high porosity of the soil, favors the removal of soil particles. The occurring process of piping on the slope in question is favored by the presence of a wooden through from which water infiltrates the ground, which increases the intensity of in-soil flow in the analyzed part of the slope.
- Open Access
- 20 April 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (9) , 4962
Influence of Rainfall Events and Surface Inclination on Overland and Subsurface Runoff Formation on Low-Permeable Soil
This paper presents the results of laboratory tests that allowed us to determine the effect of the soil surface inclination and its initial moisture content on the formation of overland and subsurface runoff. The experiments were carried out for the soil that is commonly present in the southern part of Poland, including the Outer Carpathians. The results of these measurements served as a reference for overland runoff calculations using the Richards model, simplified Green–Ampt model, and the empirical model (MSME). The results of the measurements showed that, for low-permeable soil, overland runoff is the dominant form. It was shown that a slope in the range of 2.5–5.0% does not have a significant effect on the amount of overland runoff, but affects its dynamics. The measurements also showed that the starting time and amount of overland runoff are strictly associated with the initial soil moisture content. High soil moisture content in the period preceding the onset of rainfall causes faster generation and an increase in overland runoff, which is caused by the saturation of the surface layer of the soil. This mechanism was confirmed by the results of calculations using the Richards model and measurements of the electrical resistance of the soil. Theoretical calculations showed that the results of the runoff calculations using the Richards and Green–Ampt models are strongly dependent on the hydraulic properties of the soil adopted for the analysis. It was also demonstrated that the modified MSME model satisfactorily estimates the amount of overland and subsurface runoff, but requires parameter calibration based on existing hydrological data.
- 20 April 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (9) , 4962
Open AccessInfluence of Rainfall Events and Surface Inclination on Overland and Subsurface Runoff Formation on Low-Permeable Soil
This paper presents the results of laboratory tests that allowed us to determine the effect of the soil surface inclination and its initial moisture content on the formation of overland and subsurface runoff. The experiments were carried out for the soil that is commonly present in the southern part of Poland, including the Outer Carpathians. The results of these measurements served as a reference for overland runoff calculations using the Richards model, simplified Green–Ampt model, and the empirical model (MSME). The results of the measurements showed that, for low-permeable soil, overland runoff is the dominant form. It was shown that a slope in the range of 2.5–5.0% does not have a significant effect on the amount of overland runoff, but affects its dynamics. The measurements also showed that the starting time and amount of overland runoff are strictly associated with the initial soil moisture content. High soil moisture content in the period preceding the onset of rainfall causes faster generation and an increase in overland runoff, which is caused by the saturation of the surface layer of the soil. This mechanism was confirmed by the results of calculations using the Richards model and measurements of the electrical resistance of the soil. Theoretical calculations showed that the results of the runoff calculations using the Richards and Green–Ampt models are strongly dependent on the hydraulic properties of the soil adopted for the analysis. It was also demonstrated that the modified MSME model satisfactorily estimates the amount of overland and subsurface runoff, but requires parameter calibration based on existing hydrological data.
- Open Access
The Setting of Strength Parameters in Stability Analysis of Open-Pit Slope Using the Random Set Method in the Bełchatów Lignite Mine, Central Poland
The slopes of open-pit mines are often at risk of failure. To identify this hazard, stability analyses are performed. An important element of these stability analyses is the reliable selection of input parameter values for the calculations. This selection is difficult because the slopes of the open pit are disturbed by mining activities. In such conditions, rheological processes, intensified by weathering, develop in open-pit slopes. This study is aimed at setting the strength parameters for the stability analysis of open-pit slopes with a developed slide process, using the random set method. The study was performed on the example of the open pit of the Bełchatów lignite mine, central Poland. A four-stage methodology, according to the random set method, was proposed. The methodology covered the following: site investigation, sensitivity analyses, shear strength reduction (SSR) analyses using numerical calculations, and probability analyses of the factor of safety (FoS) calculation results. The setting of the input parameters took into account the peak and residual strength parameters for each lithological unit in the physical model of the open-pit slope. Samples for laboratory tests were taken from the cores of nine test boreholes. The sensitivity analysis included all peak and residual strength parameters for each lithological unit in the body. As a result of the sensitivity analysis, specific strength parameters were adopted that would have a great impact upon the results of the calculations. Selected sets of parameter values were then used for the FoS calculations. The resultant FoS values revealed the probable slide planes. The positions of the slide planes were consistent with the interpreted slide surfaces based on the control boreholes and terrain observations. Knowledge of the slide planes positions and the values of the strength parameters enabled the designing of a securing approach for this landslide, and the taking of preventive measures to reduce this risk.
Open AccessThe Setting of Strength Parameters in Stability Analysis of Open-Pit Slope Using the Random Set Method in the Bełchatów Lignite Mine, Central Poland
The slopes of open-pit mines are often at risk of failure. To identify this hazard, stability analyses are performed. An important element of these stability analyses is the reliable selection of input parameter values for the calculations. This selection is difficult because the slopes of the open pit are disturbed by mining activities. In such conditions, rheological processes, intensified by weathering, develop in open-pit slopes. This study is aimed at setting the strength parameters for the stability analysis of open-pit slopes with a developed slide process, using the random set method. The study was performed on the example of the open pit of the Bełchatów lignite mine, central Poland. A four-stage methodology, according to the random set method, was proposed. The methodology covered the following: site investigation, sensitivity analyses, shear strength reduction (SSR) analyses using numerical calculations, and probability analyses of the factor of safety (FoS) calculation results. The setting of the input parameters took into account the peak and residual strength parameters for each lithological unit in the physical model of the open-pit slope. Samples for laboratory tests were taken from the cores of nine test boreholes. The sensitivity analysis included all peak and residual strength parameters for each lithological unit in the body. As a result of the sensitivity analysis, specific strength parameters were adopted that would have a great impact upon the results of the calculations. Selected sets of parameter values were then used for the FoS calculations. The resultant FoS values revealed the probable slide planes. The positions of the slide planes were consistent with the interpreted slide surfaces based on the control boreholes and terrain observations. Knowledge of the slide planes positions and the values of the strength parameters enabled the designing of a securing approach for this landslide, and the taking of preventive measures to reduce this risk.