Santosh B. Narasimhachary
Research Subjects
Santosh B. Narasimhachary has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
A. Saxena
5 shared publications- Ashok Saxena
Mechanical Engineering University of Arkansas Fayetteville Arkansas USA
4 shared publications Phillip W. Gravett
Siemens Energy Munich Germany
4 shared publications- Valliappa Kalyanasundaram
ICMI, Inspire AG c/o. EMPA
3 shared publications B. Dogan
EPRI 3 , Charlotte, NC28262
2 shared publications- Christopher L. Muhlstein
Material Science and Engineering Georgia Institute of Technology Atlanta Georgia USA
2 shared publications
Latest Publications
- Open Access
- 23 February 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (5) , 1794-1808
Effects of Hold Time on the Elevated Temperature Fatigue Crack Growth Behavior of Alloy 247LC‐DS
Creep–fatigue crack growth (CFCG) experiments were performed at 850°C and 950°C on nominally 12.70‐mm‐thick compact‐type specimens of alloy 247LC‐DS, a Ni‐base superalloy. The loading cycles consisted of trapezoidal waveforms with hold times of 2 and 20 min at the maximum force. The crack plane was oriented normally to the solidification direction. The fracture surfaces and the crack path‐microstructure interactions were characterized. Competing time‐ and cycle‐dependent mechanisms contributed to crack growth during these tests. Time‐dependent crack growth rates, , at 850°C and 950°C correlated with for 2‐min and 20‐min hold durations. These CFCG rates were also comparable to the creep crack growth (CCG) rates previously reported. Crack growth rates showed significant variability under all test conditions. This scatter was attributed to the formation of microcracks connecting into secondary cracks in the interdendritic regions aligned with the solidification direction. Material models representing the CCG and CFCG data are described.
- 23 February 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (5) , 1794-1808
Open AccessEffects of Hold Time on the Elevated Temperature Fatigue Crack Growth Behavior of Alloy 247LC‐DS
Creep–fatigue crack growth (CFCG) experiments were performed at 850°C and 950°C on nominally 12.70‐mm‐thick compact‐type specimens of alloy 247LC‐DS, a Ni‐base superalloy. The loading cycles consisted of trapezoidal waveforms with hold times of 2 and 20 min at the maximum force. The crack plane was oriented normally to the solidification direction. The fracture surfaces and the crack path‐microstructure interactions were characterized. Competing time‐ and cycle‐dependent mechanisms contributed to crack growth during these tests. Time‐dependent crack growth rates, , at 850°C and 950°C correlated with for 2‐min and 20‐min hold durations. These CFCG rates were also comparable to the creep crack growth (CCG) rates previously reported. Crack growth rates showed significant variability under all test conditions. This scatter was attributed to the formation of microcracks connecting into secondary cracks in the interdendritic regions aligned with the solidification direction. Material models representing the CCG and CFCG data are described.
- 23 December 2024
- Published by ASTM International in Materials Performance and Characterization
- Vol. 13 (2) , 1
Editorial: Special Issue on Fatigue and Fracture Mechanics
The study of fatigue and fracture behaviors in engineered components remains a critical area across multiple disciplines. Limits on materials behavior are among the most significant technical challenges to enhancing the safety and reliability of engineering systems. Thus, accurately defining recent advancements in analytical methods and testing techniques within fatigue and fracture mechanics for engineered structures, components, and materials is essential. This analysis encompasses both experimental research and recent developments in modeling approaches. Key areas of interest include applications of emerging analytical tools and novel experimental techniques to assess and improve durability and damage tolerance using multiscale or multiphysics-based approaches; studies on the effects of additive manufacturing processes on fatigue and fracture properties; and implications of improved modeling and experimental capabilities on fatigue life forecasting and structural health monitoring strategies. In this context, a special issue in Materials Performance and Characterization offers readers valuable insights for their research. The call for papers attracted high-quality contributions from leading scientists and engineers resulting in 11 full-length manuscripts. The main topics covered include fatigue crack growth fracture, propagation, toughness fatigue, and damage failure inspection repair. The editorial teams extend their heartfelt thanks to the authors and reviewers for their dedication and to the ASTM staff for their support in bringing this issue to publication. We hope these papers provide valuable contributions to ongoing research efforts in fatigue and fracture mechanics.
- 23 December 2024
- Published by ASTM International in Materials Performance and Characterization
- Vol. 13 (2) , 1
Editorial: Special Issue on Fatigue and Fracture Mechanics
The study of fatigue and fracture behaviors in engineered components remains a critical area across multiple disciplines. Limits on materials behavior are among the most significant technical challenges to enhancing the safety and reliability of engineering systems. Thus, accurately defining recent advancements in analytical methods and testing techniques within fatigue and fracture mechanics for engineered structures, components, and materials is essential. This analysis encompasses both experimental research and recent developments in modeling approaches. Key areas of interest include applications of emerging analytical tools and novel experimental techniques to assess and improve durability and damage tolerance using multiscale or multiphysics-based approaches; studies on the effects of additive manufacturing processes on fatigue and fracture properties; and implications of improved modeling and experimental capabilities on fatigue life forecasting and structural health monitoring strategies. In this context, a special issue in Materials Performance and Characterization offers readers valuable insights for their research. The call for papers attracted high-quality contributions from leading scientists and engineers resulting in 11 full-length manuscripts. The main topics covered include fatigue crack growth fracture, propagation, toughness fatigue, and damage failure inspection repair. The editorial teams extend their heartfelt thanks to the authors and reviewers for their dedication and to the ASTM staff for their support in bringing this issue to publication. We hope these papers provide valuable contributions to ongoing research efforts in fatigue and fracture mechanics.
- Open Access
- 10 July 2024
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 47 (10) , 3546-3560
Creep crack growth in alloy 247LC‐DS
Creep crack growth experiments were performed at 750°C, 850°C, and 950°C on nominally 3 and 12.7 mm thick compact type specimens of alloy 247LC‐DS, a Ni‐base superalloy used for hot‐section gas turbine blades. The primary crack plane was transverse to the solidification direction. The crack path–microstructure interaction was characterized. Crack growth occurred in a creep‐ductile manner and data analyses utilized time‐dependent fracture mechanics. No measurable crack growth occurred at 750°C. Cracks grew by formation, growth, and coalescence of cavities on interdendritic carbides in both the primary crack plane and normal to said plane at 850°C and 950°C. The variability in the crack growth rate was higher in thicker specimens, but the mean creep crack growth rate versus Ct relationship in 247LC‐DS was neither sensitive to test temperature ≥850°C nor specimen thickness. Quantitative relationships between da/dt and Ct were derived for mean, upper, and lower bound creep crack growth rate trends.
- 10 July 2024
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 47 (10) , 3546-3560
Open AccessCreep crack growth in alloy 247LC‐DS
Creep crack growth experiments were performed at 750°C, 850°C, and 950°C on nominally 3 and 12.7 mm thick compact type specimens of alloy 247LC‐DS, a Ni‐base superalloy used for hot‐section gas turbine blades. The primary crack plane was transverse to the solidification direction. The crack path–microstructure interaction was characterized. Crack growth occurred in a creep‐ductile manner and data analyses utilized time‐dependent fracture mechanics. No measurable crack growth occurred at 750°C. Cracks grew by formation, growth, and coalescence of cavities on interdendritic carbides in both the primary crack plane and normal to said plane at 850°C and 950°C. The variability in the crack growth rate was higher in thicker specimens, but the mean creep crack growth rate versus Ct relationship in 247LC‐DS was neither sensitive to test temperature ≥850°C nor specimen thickness. Quantitative relationships between da/dt and Ct were derived for mean, upper, and lower bound creep crack growth rate trends.
- 25 August 2023
- Published by Wiley in Journal of Applied Mechanics
- Vol. 91 (1) , 1-3
Deformation Decomposition Versus Energy Decomposition for Chemo- and Poro-Mechanics
We briefly compare the structure of two classes of popular models used to describe poro-mechanics and chemo-mechanics, wherein a fluid phase is transported within a solid phase. The multiplicative deformation decomposition has been successfully used to model permanent inelastic shape change in plasticity, solid–solid phase transformation, and thermal expansion, which has motivated its application to poro-mechanics and chemo-mechanics. However, the energetic decomposition provides a more transparent structure and advantages, such as to couple to phase-field fracture, for models of poro-mechanics and chemo-mechanics.
- 25 August 2023
- Published by Wiley in Journal of Applied Mechanics
- Vol. 91 (1) , 1-3
Deformation Decomposition Versus Energy Decomposition for Chemo- and Poro-Mechanics
We briefly compare the structure of two classes of popular models used to describe poro-mechanics and chemo-mechanics, wherein a fluid phase is transported within a solid phase. The multiplicative deformation decomposition has been successfully used to model permanent inelastic shape change in plasticity, solid–solid phase transformation, and thermal expansion, which has motivated its application to poro-mechanics and chemo-mechanics. However, the energetic decomposition provides a more transparent structure and advantages, such as to couple to phase-field fracture, for models of poro-mechanics and chemo-mechanics.
- 22 April 2022
- Published by ASTM International in Materials Performance and Characterization
- Vol. 11 (1) , 99-112
Results of a Pilot Study in Support of a Round-Robin on Creep-Fatigue Crack Growth Testing of a Creep-Brittle Material for ASTM E2760
This paper describes pilot test results from a round-robin conducted in support of the standard ASTM E2760, Standard Test Method for Creep-Fatigue Crack Growth Testing, on creep-fatigue crack growth testing. Results from the pilot study are recommended to participants to develop their individual experimental testing. This round-robin is an international effort with 10 participants from five countries from Asia, North America, and Europe. All participants are testing compact type (C(T)) specimens according to the procedure described in the standard. A few participants are evaluating the Kb-bar (surface crack) specimen configuration. The test material is Inconel-718 (IN718) nickel-based alloy, which is a creep-brittle alloy. Pilot creep-fatigue crack growth tests were conducted at 600°C using C(T) specimens under constant load amplitude conditions. The tests were conducted at hold times of 0, 60, and 600 s. Creep-fatigue crack growth rates were analyzed using the methods proposed and included in the test standard. It was found that the procedures followed throughout the pilot test program were sufficient in generating the desired outcomes. As a result, it is proposed that the various participants follow the procedures and test matrix as close as possible and document any deviations. This will allow data from the various participants to be assessed and determine the levels of precision and bias in creep-fatigue crack growth data obtained using the ASTM standard.
- 22 April 2022
- Published by ASTM International in Materials Performance and Characterization
- Vol. 11 (1) , 99-112
Results of a Pilot Study in Support of a Round-Robin on Creep-Fatigue Crack Growth Testing of a Creep-Brittle Material for ASTM E2760
This paper describes pilot test results from a round-robin conducted in support of the standard ASTM E2760, Standard Test Method for Creep-Fatigue Crack Growth Testing, on creep-fatigue crack growth testing. Results from the pilot study are recommended to participants to develop their individual experimental testing. This round-robin is an international effort with 10 participants from five countries from Asia, North America, and Europe. All participants are testing compact type (C(T)) specimens according to the procedure described in the standard. A few participants are evaluating the Kb-bar (surface crack) specimen configuration. The test material is Inconel-718 (IN718) nickel-based alloy, which is a creep-brittle alloy. Pilot creep-fatigue crack growth tests were conducted at 600°C using C(T) specimens under constant load amplitude conditions. The tests were conducted at hold times of 0, 60, and 600 s. Creep-fatigue crack growth rates were analyzed using the methods proposed and included in the test standard. It was found that the procedures followed throughout the pilot test program were sufficient in generating the desired outcomes. As a result, it is proposed that the various participants follow the procedures and test matrix as close as possible and document any deviations. This will allow data from the various participants to be assessed and determine the levels of precision and bias in creep-fatigue crack growth data obtained using the ASTM standard.
- 23 June 2019
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 42 (9) , 2053-2060
Accounting for crack tip cyclic plasticity and creep reversal in estimating (Ct)avg during creep‐fatigue crack growth
Creep‐fatigue crack growth (C‐FCG) rates in a P91 steel at 625°C were correlated as the average time rate of crack growth during hold time, (da/dt)avg, with (Ct)avg. At 60‐second hold time, the rates were lower than for 600‐second hold time. At 600‐second hold time, the crack growth rates converged on to the creep crack growth rate (CCGR) trend. Thus, the CCGR trend represents the upper bound for time‐dependent crack growth rates in P91 materials. The analytical expressions based on considering just the elastic and secondary creep deformation rates overestimated the magnitudes of (Ct)avg by as much as a factor of 10 for the 600‐second hold time tests. After accounting for the effects of cyclic plasticity during unloading, and accounting for only partial reversal of creep strains accumulated during hold time, the estimates of (Ct)avg compared well with the measured values. CR represents the extent of crack tip creep strain reversal, and tpl is the time required for the crack tip creep zone during the hold time to become equivalent in size to the cyclic plastic zone in terms of stress carried by that region. Together, these parameters accurately account for the effects of crack tip cyclic plasticity on the magnitude of (Ct)avg.Both tpl and CR depend on material properties, and the latter also depends on the hold time. A parameter ϕ is introduced that is dependent only on material properties and from which CR can be estimated for a given hold time. tpl and ϕ can be reported as part of the test results from C‐FCG testing.
- 23 June 2019
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 42 (9) , 2053-2060
Accounting for crack tip cyclic plasticity and creep reversal in estimating (Ct)avg during creep‐fatigue crack growth
Creep‐fatigue crack growth (C‐FCG) rates in a P91 steel at 625°C were correlated as the average time rate of crack growth during hold time, (da/dt)avg, with (Ct)avg. At 60‐second hold time, the rates were lower than for 600‐second hold time. At 600‐second hold time, the crack growth rates converged on to the creep crack growth rate (CCGR) trend. Thus, the CCGR trend represents the upper bound for time‐dependent crack growth rates in P91 materials. The analytical expressions based on considering just the elastic and secondary creep deformation rates overestimated the magnitudes of (Ct)avg by as much as a factor of 10 for the 600‐second hold time tests. After accounting for the effects of cyclic plasticity during unloading, and accounting for only partial reversal of creep strains accumulated during hold time, the estimates of (Ct)avg compared well with the measured values. CR represents the extent of crack tip creep strain reversal, and tpl is the time required for the crack tip creep zone during the hold time to become equivalent in size to the cyclic plastic zone in terms of stress carried by that region. Together, these parameters accurately account for the effects of crack tip cyclic plasticity on the magnitude of (Ct)avg.Both tpl and CR depend on material properties, and the latter also depends on the hold time. A parameter ϕ is introduced that is dependent only on material properties and from which CR can be estimated for a given hold time. tpl and ϕ can be reported as part of the test results from C‐FCG testing.
- 1 January 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (1) , 448-467
Results of the ASTM Round Robin on Creep-Fatigue Crack Growth Testing of a P91 Steel
This article summarizes the results of a round robin (RR) study begun in 2013 to evaluate ASTM E2760-10, Standard Method for Creep-Fatigue Crack Growth Testing (Superseded). Thirteen laboratories from around the world conducted testing and reported results. The test material was a creep-ductile, ASTM Grade P91 9Cr-1Mo steel. All testing was performed using nominally 50-mm-wide compact tension specimens at a test temperature of 625°C using trapezoidal waveforms with hold times of 0, 60, and 600 s. The 600-s hold time condition was the primary condition used for assessing interlaboratory variability among crack growth rates. Loading/unloading times were 2 s each. All laboratories tested duplicate specimens that were identical in all respects except for the force amplitude levels. Results from prior studies that included tensile, creep deformation and rupture, and low-cycle fatigue properties were available for the analysis of tests conducted as part of this RR testing. Crack growth rates at 600-s hold time reported by six laboratories fall within a 95 % confidence band (interlaboratory variability) separated by a factor of 6.16 when correlated with ΔK, 10.76 when correlated with measured vales of (Ct)avg, and 7.17 when correlated with calculated values of (Ct)avg.
- 1 January 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (1) , 448-467
Results of the ASTM Round Robin on Creep-Fatigue Crack Growth Testing of a P91 Steel
This article summarizes the results of a round robin (RR) study begun in 2013 to evaluate ASTM E2760-10, Standard Method for Creep-Fatigue Crack Growth Testing (Superseded). Thirteen laboratories from around the world conducted testing and reported results. The test material was a creep-ductile, ASTM Grade P91 9Cr-1Mo steel. All testing was performed using nominally 50-mm-wide compact tension specimens at a test temperature of 625°C using trapezoidal waveforms with hold times of 0, 60, and 600 s. The 600-s hold time condition was the primary condition used for assessing interlaboratory variability among crack growth rates. Loading/unloading times were 2 s each. All laboratories tested duplicate specimens that were identical in all respects except for the force amplitude levels. Results from prior studies that included tensile, creep deformation and rupture, and low-cycle fatigue properties were available for the analysis of tests conducted as part of this RR testing. Crack growth rates at 600-s hold time reported by six laboratories fall within a 95 % confidence band (interlaboratory variability) separated by a factor of 6.16 when correlated with ΔK, 10.76 when correlated with measured vales of (Ct)avg, and 7.17 when correlated with calculated values of (Ct)avg.
- 1 August 2018
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 199, 760-772
A single edge notch specimen for fatigue, creep-fatigue and thermo-mechanical fatigue crack growth testing
- 1 August 2018
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 199, 760-772
A single edge notch specimen for fatigue, creep-fatigue and thermo-mechanical fatigue crack growth testing
- 11 June 2018
- Published by ASME International
LCF Initiated - HCF Propagated Crack Life Estimation of Gas Turbine Bolts
This paper discusses the methodology to calculate high cycle fatigue (HCF) crack propagation life of gas turbine bolts and compares two dimensional (2D) HCF crack propagation life to three dimensional (3D) HCF crack propagation life. Gas turbine bolts when exposed to fatigue loading are prone to crack initiation and propagation (structural failure) during operation. In such cases cracks mostly are initiated by low cycle fatigue (LCF) and propagated by HCF. Therefore in current illustration the authors have evaluated crack propagation primarily initiated by low cycle fatigue and propagated by high cycle fatigue. 2D and 3D fracture methodology approaches had been used for analytical evaluation. The authors conclude on the efficacy of both the methods based on the data from the field. The coupling joint bolts located in the engine mid-section, which are used to join compressor rotor with turbine rotor are being considered for crack evaluation studies. The coupling bolts located in mid-section are primarily loaded by high axial bolt pre-loads needed to keep the joint intact, as well as loaded in bending due to rotor gravity sag. The crack propagation life is evaluated and validated with field data using cracked bolt specimen from the field.
- 11 June 2018
- Published by ASME International
LCF Initiated - HCF Propagated Crack Life Estimation of Gas Turbine Bolts
This paper discusses the methodology to calculate high cycle fatigue (HCF) crack propagation life of gas turbine bolts and compares two dimensional (2D) HCF crack propagation life to three dimensional (3D) HCF crack propagation life. Gas turbine bolts when exposed to fatigue loading are prone to crack initiation and propagation (structural failure) during operation. In such cases cracks mostly are initiated by low cycle fatigue (LCF) and propagated by HCF. Therefore in current illustration the authors have evaluated crack propagation primarily initiated by low cycle fatigue and propagated by high cycle fatigue. 2D and 3D fracture methodology approaches had been used for analytical evaluation. The authors conclude on the efficacy of both the methods based on the data from the field. The coupling joint bolts located in the engine mid-section, which are used to join compressor rotor with turbine rotor are being considered for crack evaluation studies. The coupling bolts located in mid-section are primarily loaded by high axial bolt pre-loads needed to keep the joint intact, as well as loaded in bending due to rotor gravity sag. The crack propagation life is evaluated and validated with field data using cracked bolt specimen from the field.