MMMarisa Moreno-Ríos

Marisa Moreno-Ríos

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Marisa Moreno-Ríos has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    On the Observation of the Central Dark Line in the Human Tooth Enamel Crystals Through SEM, TEM, STEM, and AFM Microscopes

    by J. Reyes-Gasga, Marisa Moreno-Rios, A. Rodríguez-Gómez, Etienne Bres

    We examine the image contrasts presented at micrometric and nanometric scales of the scanning electron microscope (SEM), transmission electron microscope (TEM), scanning transmission electron microscope (STEM), and atomic force microscope (AFM) in the tapping mode, looking for the observation of the central feature known as “the central dark line” (CDL) in the structure of human tooth enamel crystals. Since our interest is in inorganic material, mainly at the nanometric scale, the enamel samples for SEM and AFM were polished following a metallographic procedure, using progressively finer silicon carbide papers and etching with orthophosphoric acid. For TEM and STEM, the samples were produced by the focused ion beam (FIB) technique. The CDL images were well recorded using TEM and STEM, but not in SEM and AFM images. SEM images revealed the size and morphology of the enamel crystals, while AFM images revealed spherical and band‐like structures. The observation of the CDL using TEM and STEM suggests that it may represent a potential chemical compositional site.

  • Comportamiento microestructural y mecánico de CADIs microaleados con molibdeno

    by Eduardo Colin-García, Alejandro Cruz-Ramírez, Ricardo Gerardo Sánchez-Alvarado, Marisa Moreno-Ríos

  • Open Access

    Diseño y análisis numérico de una plataforma de 4 bolas para pruebas de lubricación

    by Diana Cuautle Lezama, Armando Irvin Martínez Pérez, Edgar Ernesto Vera Cárdenas, Marisa Moreno Ríos, Jesus Cornelio Mendoza Mendoza

    Una de principales causas de un desempeño mecánico deficiente en máquinas industriales, es la mala selección y calidad de los lubricantes, esto se deriva a la falta de comprensión de sus propiedades tribológicas. Por esta razón es importante complementar la información fisicoquímica de los lubricantes con los resultados de los ensayos tribológicos impactando directamente a la productividad y la eficiencia de los procesos industriales. Para determinar las propiedades tribológicas de lubricantes, en este trabajo se presenta el diseño conceptual de una plataforma de 4 bolas bajo las especificaciones de la norma ASTM D2266. Se aplicó la metodología de diseño de Nigel Cross, la cual aporta resultados para satisfacer las subfunciones requeridas y objetivos establecidos. El diseño conceptual se validó numéricamente con el software ANSYS, a partir del análisis de esfuerzos y deformaciones del bastidor, la sujeción de la bola y de la celda, manifestando la importancia del material aplicado al sistema para evitar fallas durante la operación.

  • Open Access

    Field and laboratory assessments of the friction coefficient at a railhead

    by Marisa Moreno-Ríos, Ezequiel A Gallardo-Hernández, Manuel Vite-Torres, Alejandro Peña-Bautista

    The aim of this work was to prove that the oil applied to the wheel flange using on-board lubricators not only alters the friction coefficient between wheel and rail but also influences the braking and acceleration performance of trains on one of the lines of the metro in Mexico City. A series of tests were carried out in the presence of an oil lubricant, both in the laboratory and in the field, using a pendulum tester. It was observed that the oil migrated from the rail corner to the top of the rail. In another set of experiments, water was sprayed onto the lubricant on the top of the rail. The results indicated that under these conditions, the friction coefficient has a low value in rail sections where a high value of the friction coefficient is required. Tests with water/oil mixtures presented similar levels of friction to the oil-only tests. A set of tests were performed after the rail surface was cleaned and the oil lubricant and water were applied together. The laboratory and field tests showed similar behaviour trends for the friction coefficient. The pendulum method can be used to assess railhead friction on short-length sections of rail. Points are made regarding the conditioning of the pads and calibration of the pendulum arm.


  • A study of the abrasive resistance of sputtered CrN coatings deposited on AISI 316 and AISI H13 steel substrates using steel particles

    by M. Vite, M. Moreno-Ríos, E.A. Gallardo Hernández, J.R. Laguna-Camacho


  • Coating Characterzation in CrN Deposited by Magnetron Sputtering Method on AISI 316 Steel

    by I. Hilerio, M. Vite, M. Moreno, M. A. Barron, H. Jime´nez, B. Vazquez

    Chromium Nitride (CrN) thin films were deposited on AISI steel 316 substrates by means of the reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a DC source. For the second coating a negative substrate bias voltage was applied. X ray diffraction, quantitative energy dispersion and scanning electron microscope were employed to characterize the two different phases, their chemical composition as well as their microstructure. In addition, a microhardness test was carried out. The results show that a better phase formation of CrN thin films was achieved when a heating source was present (first case). Both coatings presented homogeneous surface. Their compositions show differences even when the gases flowing are the same in composition. Regarding to the hardness test results, there can be found a higher value when using a heating source.