Deepak Kumar
Research Subjects
Deepak Kumar has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
A. Kumar
7 shared publicationsN. Mehta
Department of Physics, Pranveer Singh Institute of Technology, Kanpur, India
4 shared publicationsA Kumar
Department of Physics, Harcourt Butler Technological Institute, Kanpur, India
2 shared publicationsAnjani Kumar
2 shared publicationsN Mehta
Department of Physics, Pranveer Singh Institute of Technology, Kanpur, India
2 shared publications- Neeraj Mehta
Department of Physics, Institute of Science, Banaras Hindu University, Varanasi, India
2 shared publications
Latest Publications
- 1 August 2018
- Published by American Scientific Publishers in Materials Focus
- Vol. 7 (4) , 509-514
Optical Properties of Amorphous Thin Films of Se90Sb10–xAgx
Thin films of Se90Sb10–x Ag x (x = 4, 6, 8) glassy alloys have been deposited onto glass substrates by thermal evaporation technique under vacuum. Transmission spectra T (λ) of the films were obtained in the wavelength range of 400–1200 nm. Estimation of the optical constants like refractive index (n), real dielectric constant (ε'), extinction coefficient (k), imaginary dielectric constant (ε''), absorption coefficient (α) is made by straightforward analysis proposed by Swanepoel. It is found that n, k, α decrease with the increase in the wavelength. Tauc relation for allowed non direct transition describes the optical transition in the studied films. Band gap is found to increase with the increase in Ag concentration.
- 1 August 2018
- Published by American Scientific Publishers in Materials Focus
- Vol. 7 (4) , 509-514
Optical Properties of Amorphous Thin Films of Se90Sb10–xAgx
Thin films of Se90Sb10–x Ag x (x = 4, 6, 8) glassy alloys have been deposited onto glass substrates by thermal evaporation technique under vacuum. Transmission spectra T (λ) of the films were obtained in the wavelength range of 400–1200 nm. Estimation of the optical constants like refractive index (n), real dielectric constant (ε'), extinction coefficient (k), imaginary dielectric constant (ε''), absorption coefficient (α) is made by straightforward analysis proposed by Swanepoel. It is found that n, k, α decrease with the increase in the wavelength. Tauc relation for allowed non direct transition describes the optical transition in the studied films. Band gap is found to increase with the increase in Ag concentration.
- 1 October 2017
- Published by American Scientific Publishers in Materials Focus
- Vol. 6 (5) , 597-601
Dielectric Properties and A.C. Conductivity in Glassy Se90Sb10: Estimation of Density of Defect States
Glassy alloys of Se90Sb10 are prepared by melt quenching technique. The amorphous nature of the so prepared alloy is confirmed by X-ray diffraction technique. Se90Sb10 pallets are prepared by compressing the fine powder of glassy alloy in a die up to a load of about 5–6 tons. The a.c. conductivity and dielectric properties of these samples are studied in the temperature range (308 K–373 K) and frequency range (500 Hz–500 kHz). It has been observed that the a.c. conductivity σ ac(ω) ∝ ωs where s is found to be less than unity. It has been observed that the values of dielectric constant and dielectric loss are temperature dependent and decreases with the increase in temperature. Applying Guintini's criteria the maximum barrier height has been calculated and found to be 0.15 eV which is in close agreement with the theory of hopping conduction over potential barrier as suggested by Elliott. A close resemblance is found between theoretical and experimental results which are explained on the basis of correlated barrier hopping (CBH) model. The experimental data has been fitted to the theory of a.c. conductivity, and density of charged defect states has been estimated for the glass under consideration. In the present case it has been observed that bipolaron hopping dominates over single polaron hopping, which is explained in terms of lower value of potential barrier.
- 1 October 2017
- Published by American Scientific Publishers in Materials Focus
- Vol. 6 (5) , 597-601
Dielectric Properties and A.C. Conductivity in Glassy Se90Sb10: Estimation of Density of Defect States
Glassy alloys of Se90Sb10 are prepared by melt quenching technique. The amorphous nature of the so prepared alloy is confirmed by X-ray diffraction technique. Se90Sb10 pallets are prepared by compressing the fine powder of glassy alloy in a die up to a load of about 5–6 tons. The a.c. conductivity and dielectric properties of these samples are studied in the temperature range (308 K–373 K) and frequency range (500 Hz–500 kHz). It has been observed that the a.c. conductivity σ ac(ω) ∝ ωs where s is found to be less than unity. It has been observed that the values of dielectric constant and dielectric loss are temperature dependent and decreases with the increase in temperature. Applying Guintini's criteria the maximum barrier height has been calculated and found to be 0.15 eV which is in close agreement with the theory of hopping conduction over potential barrier as suggested by Elliott. A close resemblance is found between theoretical and experimental results which are explained on the basis of correlated barrier hopping (CBH) model. The experimental data has been fitted to the theory of a.c. conductivity, and density of charged defect states has been estimated for the glass under consideration. In the present case it has been observed that bipolaron hopping dominates over single polaron hopping, which is explained in terms of lower value of potential barrier.
- 1 August 2017
- Published by American Scientific Publishers in Materials Focus
- Vol. 6 (4) , 424-427
The Peculiar Role of the Third Element Indium in Density of Defect States of Se90Ge10 Thin Films
The present paper reports the space charge limited conduction (SCLC) measurements in Se90Ge10–x In x (x = 2, 6) amorphous thin films. For this purpose, I–V measurements have been taken at different temperatures. The results show that an ohmic behavior is observed at low electric fields (E 103 V/cm) while, at higher electric fields (E ∼ 104 V/cm), a super-ohmic behavior is observed. An analysis of the experimental data confirms the presence of space charge limited conduction (SCLC) in the present glassy materials. Density of defect states (DOS) near Fermi level is calculated by fitting the data to SCLC theory. The peculiar role of the third element Indium, as an impurity in Se90Ge10 binary glassy alloy, is also discussed in terms of electro-negativity difference between the constituent elements.
- 1 August 2017
- Published by American Scientific Publishers in Materials Focus
- Vol. 6 (4) , 424-427
The Peculiar Role of the Third Element Indium in Density of Defect States of Se90Ge10 Thin Films
The present paper reports the space charge limited conduction (SCLC) measurements in Se90Ge10–x In x (x = 2, 6) amorphous thin films. For this purpose, I–V measurements have been taken at different temperatures. The results show that an ohmic behavior is observed at low electric fields (E 103 V/cm) while, at higher electric fields (E ∼ 104 V/cm), a super-ohmic behavior is observed. An analysis of the experimental data confirms the presence of space charge limited conduction (SCLC) in the present glassy materials. Density of defect states (DOS) near Fermi level is calculated by fitting the data to SCLC theory. The peculiar role of the third element Indium, as an impurity in Se90Ge10 binary glassy alloy, is also discussed in terms of electro-negativity difference between the constituent elements.
- Open Access
- 23 June 2017
- Published by Taylor & Francis in Journal of Taibah University for Science
- Vol. 11 (6) , 1289-1295
Role of Ag additives on light-induced metastable defects in a Se–In glassy system
The paper reports the role of Ag additives on light induced metastable defects in Se–In glassy alloys using a well-known thermally stimulated current (TSC) technique. Amorphous thin films of Se90In10−xAgx (x = 0, 2, 4, 8) were prepared by thermal evaporation. Measurements were made in the given thin films prior to and after exposing amorphous thin films to white light for different exposure times (0–1.5 hrs). The density of light induced metastable defects increases with exposure time, and the fractional increase in light induced metastable defect density decreases as Ag concentration increases.
- 23 June 2017
- Published by Taylor & Francis in Journal of Taibah University for Science
- Vol. 11 (6) , 1289-1295
Open AccessRole of Ag additives on light-induced metastable defects in a Se–In glassy system
The paper reports the role of Ag additives on light induced metastable defects in Se–In glassy alloys using a well-known thermally stimulated current (TSC) technique. Amorphous thin films of Se90In10−xAgx (x = 0, 2, 4, 8) were prepared by thermal evaporation. Measurements were made in the given thin films prior to and after exposing amorphous thin films to white light for different exposure times (0–1.5 hrs). The density of light induced metastable defects increases with exposure time, and the fractional increase in light induced metastable defect density decreases as Ag concentration increases.
- 1 November 2016
- Published by American Scientific Publishers in Advanced Science Letters
- Vol. 22 (11) , 3954-3957
Applicability of Thermally Stimulated Currents Technique to Estimate Light Induced Meta-Stable Defects in A-Se90In2Ag8 Thin Films
Present study reports the quantitative estimation of light induced defects in vacuum evaporated thin films of Se90In2Ag8 by using thermally stimulated current (TSC) technique. These Measurements have been made in a vacuum ~10−3 Torr before and after exposing amorphous films to white light for different exposure times from 0 to 1.5 hours. It is found that the density of light induced defects increases with the exposure time.
- 1 November 2016
- Published by American Scientific Publishers in Advanced Science Letters
- Vol. 22 (11) , 3954-3957
Applicability of Thermally Stimulated Currents Technique to Estimate Light Induced Meta-Stable Defects in A-Se90In2Ag8 Thin Films
Present study reports the quantitative estimation of light induced defects in vacuum evaporated thin films of Se90In2Ag8 by using thermally stimulated current (TSC) technique. These Measurements have been made in a vacuum ~10−3 Torr before and after exposing amorphous films to white light for different exposure times from 0 to 1.5 hours. It is found that the density of light induced defects increases with the exposure time.
- Open Access
- 20 May 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (11) , 14085-14094
Engineering the optical response of a-Se thin films by employing morphological disorder
In this article, we experimentally demonstrate for the first time that photobleaching (PB) can be induced in morphologically disordered a-Se thin film, an observation which is opposite of the previously well-known photodarkening (PD) effects in morphologically ordered films. Further, the optical response of the film shows many fold increase with increase in control beam intensity. To explain the observed extraordinary phenomenon, we have proposed a model based on the morphological disorder of a modified surface and its subsequent photo-annealing. Our results demonstrate an efficient and yet simple new method to engineer the optical response of photosensitive thin films. We envision that this process can open up many avenues in optical field-enhanced absorption-based technologies.
- 20 May 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (11) , 14085-14094
Open AccessEngineering the optical response of a-Se thin films by employing morphological disorder
In this article, we experimentally demonstrate for the first time that photobleaching (PB) can be induced in morphologically disordered a-Se thin film, an observation which is opposite of the previously well-known photodarkening (PD) effects in morphologically ordered films. Further, the optical response of the film shows many fold increase with increase in control beam intensity. To explain the observed extraordinary phenomenon, we have proposed a model based on the morphological disorder of a modified surface and its subsequent photo-annealing. Our results demonstrate an efficient and yet simple new method to engineer the optical response of photosensitive thin films. We envision that this process can open up many avenues in optical field-enhanced absorption-based technologies.
- 20 June 2009
- Published by Taylor & Francis in Journal of Modern Optics
- Vol. 56 (11) , 1272-1275
Effect of In additive on the photosensitivity of glassy Se80Te20alloy
Photo-electrical measurements are done on thin films of Se80−x Te20In x (0 ≤ x ≤ 20) to see the effect of In on the photoconductive properties of binary Se80Te20 alloy. The photosensitivity (σph/σd) and activation energy of photoconduction (ΔE ph) are determined for this purpose. It has been found that σph/σd and ΔE ph are decreased with increasing concentration of the third element. The results are explained in terms of the increase in density of the defect states with the increase in concentration of the additive in thin films of Se80−x Te20In x .
- 20 June 2009
- Published by Taylor & Francis in Journal of Modern Optics
- Vol. 56 (11) , 1272-1275
Effect of In additive on the photosensitivity of glassy Se80Te20alloy
Photo-electrical measurements are done on thin films of Se80−x Te20In x (0 ≤ x ≤ 20) to see the effect of In on the photoconductive properties of binary Se80Te20 alloy. The photosensitivity (σph/σd) and activation energy of photoconduction (ΔE ph) are determined for this purpose. It has been found that σph/σd and ΔE ph are decreased with increasing concentration of the third element. The results are explained in terms of the increase in density of the defect states with the increase in concentration of the additive in thin films of Se80−x Te20In x .
- 14 January 2009
- Published by Taylor & Francis in Phase Transitions
- Vol. 82 (1) , 75-86
Amorphous to crystalline phase transition in glassy Se65Te20Ag15alloy
In the present work, the amorphous to crystalline phase transition of chalcogenide glass Se65Te20Ag15 has been studied using differential scanning calorimetric (DSC) measurements. The heating rate dependence of crystallization peaks has been used for the determination of activation energies of glass transition (E g) and crystallization (E c). Different non-isothermal methods have been used for this purpose. Other useful kinetic parameters such as the order parameter (n), the numerical factor of crystallization mechanism (m) and the frequency factor (K o) of the rate constant (K) have been also determined.
- 14 January 2009
- Published by Taylor & Francis in Phase Transitions
- Vol. 82 (1) , 75-86
Amorphous to crystalline phase transition in glassy Se65Te20Ag15alloy
In the present work, the amorphous to crystalline phase transition of chalcogenide glass Se65Te20Ag15 has been studied using differential scanning calorimetric (DSC) measurements. The heating rate dependence of crystallization peaks has been used for the determination of activation energies of glass transition (E g) and crystallization (E c). Different non-isothermal methods have been used for this purpose. Other useful kinetic parameters such as the order parameter (n), the numerical factor of crystallization mechanism (m) and the frequency factor (K o) of the rate constant (K) have been also determined.
- 1 February 2008
- Published by Pleiades Publishing Ltd in Glass Physics and Chemistry
- Vol. 34 (1) , 42-46
Investigation of the Meyer-Neldel rule for AC conduction in glassy Se100 − x Te x alloys
In many amorphous and liquid semiconductors and other class of materials, the Meyer-Neldel rule is observed in the dc conductivity, where the preexponential factor (σ0) is found to increase...
- 1 February 2008
- Published by Pleiades Publishing Ltd in Glass Physics and Chemistry
- Vol. 34 (1) , 42-46
Investigation of the Meyer-Neldel rule for AC conduction in glassy Se100 − x Te x alloys
In many amorphous and liquid semiconductors and other class of materials, the Meyer-Neldel rule is observed in the dc conductivity, where the preexponential factor (σ0) is found to increase...