Nilesh Ganpatrao Patil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nilesh Ganpatrao Patil has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
P. K. Brahmankar
Dr. Babasaheb Ambedkar Technological University, Lonere 402103, India
6 shared publicationsSachin M. Agrawal
6 shared publicationsP.K. Brahmankar
5 shared publicationsL. G. Navale
MES’ College of Engineering, Pune, India
3 shared publications- Subhash Lahane
Marathwada Institute of Technology
3 shared publications - Atul Kulkarni
Department of Mechanical Engineering, Vishwakarma Institute of Technology, Pune, India
2 shared publications
Latest Publications
- 16 June 2025
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 27 (2)
Experimental investigation of graphene oxide-based nano cutting fluid in drilling of aluminum matrix composite reinforced with SiC particles under nano-MQL conditions
Introduction. Minimum Quantity Lubrication (MQL) is effectively employed as suitable cooling strategy. However, compared to flood cooling, which is widely used in the industry, MQL is characterized by a lower heat dissipation capacity. While thermal shock is reported in flood cooling, the use of MQL ensures a smoother chip removal and reduces the risk of thermal stress. Research methods. Within the scope of this study, experimental investigations were carried out on drilling of aluminum matrix composite (MMC) reinforced with silicon carbide (Al-SiC MMC) using AlCrN PVD-coated drills (drill diameter 8 mm). MMC samples were manufactured with varying volume fractions of SiC (10–30%). The aim of the experiments was to study the influence of non-edible vegetable oil with the addition of graphene oxide (used as a cutting fluid) on the drilling process of AlSiC MMC. The cutting speed (30–150 m/min), feed rate (0.05–0.25 mm/rev), volume fraction of SiC (10–30%), and MQL flow rate (60–180 ml/h) were selected as input process parameters. Their response parameters were cutting force, torque, surface roughness, hole circularity, and burr height during high-speed drilling of MMC. The undi (Calophyllum inophyllum) oil parameters were determined in accordance with the ASTM 6751 standard. The surface morphology and elemental analysis of graphene oxide were investigated using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDAX). The purpose of the work. The use of nano-cutting fluid in combination with MQL is one of the promising approaches for further improving the characteristics of MQL, especially when drilling difficult-to-machine materials. The introduction of nanomaterials into MQL contributes to reducing friction at the tool-chip interface, which leads to a decrease in cutting temperature. These methods facilitate the machining of lightweight and difficult-to-machine materials, in particular, aluminum-based metal matrix composites (MMCs), which are widely used in the automotive and aerospace industries. Results and Discussion. It was found that the use of graphene oxide nanoparticles dispersed in non-edible undi (Calophyllum inophyllum) oil represents a promising alternative to traditional cutting fluids in drilling MMC. The aim of the study was to develop semi-empirical models for predicting surface roughness and temperature for various compositions of MMC. Increased cutting efficiency is achieved by precisely determining the temperature in the machining zone. However, the practical determination of the cutting temperature in each specific case involves significant labor and financial costs. It was additionally found that graphene oxide nanoparticles mixed with non-edible undi (Calophyllum inophyllum) oil represent an effective alternative to traditional cutting fluids in drilling MMCs. The present work develops a comprehensive empirical formula for predicting the theoretical temperature and surface roughness. It was found that the majority of the power input into the machining process is transformed into thermal energy.
- 16 June 2025
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 27 (2)
Experimental investigation of graphene oxide-based nano cutting fluid in drilling of aluminum matrix composite reinforced with SiC particles under nano-MQL conditions
Introduction. Minimum Quantity Lubrication (MQL) is effectively employed as suitable cooling strategy. However, compared to flood cooling, which is widely used in the industry, MQL is characterized by a lower heat dissipation capacity. While thermal shock is reported in flood cooling, the use of MQL ensures a smoother chip removal and reduces the risk of thermal stress. Research methods. Within the scope of this study, experimental investigations were carried out on drilling of aluminum matrix composite (MMC) reinforced with silicon carbide (Al-SiC MMC) using AlCrN PVD-coated drills (drill diameter 8 mm). MMC samples were manufactured with varying volume fractions of SiC (10–30%). The aim of the experiments was to study the influence of non-edible vegetable oil with the addition of graphene oxide (used as a cutting fluid) on the drilling process of AlSiC MMC. The cutting speed (30–150 m/min), feed rate (0.05–0.25 mm/rev), volume fraction of SiC (10–30%), and MQL flow rate (60–180 ml/h) were selected as input process parameters. Their response parameters were cutting force, torque, surface roughness, hole circularity, and burr height during high-speed drilling of MMC. The undi (Calophyllum inophyllum) oil parameters were determined in accordance with the ASTM 6751 standard. The surface morphology and elemental analysis of graphene oxide were investigated using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDAX). The purpose of the work. The use of nano-cutting fluid in combination with MQL is one of the promising approaches for further improving the characteristics of MQL, especially when drilling difficult-to-machine materials. The introduction of nanomaterials into MQL contributes to reducing friction at the tool-chip interface, which leads to a decrease in cutting temperature. These methods facilitate the machining of lightweight and difficult-to-machine materials, in particular, aluminum-based metal matrix composites (MMCs), which are widely used in the automotive and aerospace industries. Results and Discussion. It was found that the use of graphene oxide nanoparticles dispersed in non-edible undi (Calophyllum inophyllum) oil represents a promising alternative to traditional cutting fluids in drilling MMC. The aim of the study was to develop semi-empirical models for predicting surface roughness and temperature for various compositions of MMC. Increased cutting efficiency is achieved by precisely determining the temperature in the machining zone. However, the practical determination of the cutting temperature in each specific case involves significant labor and financial costs. It was additionally found that graphene oxide nanoparticles mixed with non-edible undi (Calophyllum inophyllum) oil represent an effective alternative to traditional cutting fluids in drilling MMCs. The present work develops a comprehensive empirical formula for predicting the theoretical temperature and surface roughness. It was found that the majority of the power input into the machining process is transformed into thermal energy.
- 15 March 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (1)
Semi empirical modeling of cutting temperature and surface roughness in turning of engineering materials with TiAlN coated carbide tool
Introduction. In manufacturing, obtaining a specified surface roughness of the machined components is of great importance to fulfill functional requirements. However, this is significantly affected by the heat generated during processing, potentially causing variations in dimensional accuracy. The surface roughness significantly affects the fatigue performance of the component, while the cutting tool's lifespan is dictated by the generation of cutting temperatures. The purpose of the study is to create semi-empirical models for predicting surface roughness and temperature of different work materials. Improved cutting performance is achieved by precisely determining the cutting temperature in the zone being machined. However, calculating the cutting temperature for each specific case is fraught with difficulties in terms of labor resources and financial investments. This paper presents a comprehensive empirical formula designed to predict both theoretical temperature and surface roughness. The methodology. The surface roughness and temperature values were evaluated for EN 8, Al 380, SS 316 and SAE 8620 materials using TiAlN coated carbide tool. The TiAlN coating was formed using Physical Vapor Deposition (PVD) Technique. The response surface methodology was used to prepare predictive models. Cutting speed (140 to 340 m/min), feed (0.08 to 0.24 mm/rev) and depth of cut (0.6 to 1.0 mm) was used as input parameters for measuring the performance of all material in terms of surface roughness and cutting temperature. The tool-work thermocouple principle was used to measure the temperature at the chip-tool interface. A Novel Calibration Setup was developed to establish a connection between the electromotive force (EMF) generated during machining and the cutting temperature. Results and Discussion. It is observed that the power required for machining was largely transformed into heat. The highest cutting temperature is recorded when machining of SS 316 followed by SAE 8620, EN 8. However, low temperature is reported during machining of Al 380 and it is mainly governed by the thermal conductivity of the material. The lowest surface roughness is observed in SAE 8620, EN 8 material followed by SS 316 and Al 380. Semi-empirical method and regression model equations show a good agreement with each other. Statistical analysis of nonlinear estimation reveals that the cutting speed, feed, and density of the material have a greater effect on surface roughness, whereas the depth of cut has a greater effect on temperature generation. The study will be very useful for predicting industrial productivity when machining of EN 8, Al 380, SS 316 and SAE 8620 materials with TiAlN-coated carbide tool.
- 15 March 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (1)
Semi empirical modeling of cutting temperature and surface roughness in turning of engineering materials with TiAlN coated carbide tool
Introduction. In manufacturing, obtaining a specified surface roughness of the machined components is of great importance to fulfill functional requirements. However, this is significantly affected by the heat generated during processing, potentially causing variations in dimensional accuracy. The surface roughness significantly affects the fatigue performance of the component, while the cutting tool's lifespan is dictated by the generation of cutting temperatures. The purpose of the study is to create semi-empirical models for predicting surface roughness and temperature of different work materials. Improved cutting performance is achieved by precisely determining the cutting temperature in the zone being machined. However, calculating the cutting temperature for each specific case is fraught with difficulties in terms of labor resources and financial investments. This paper presents a comprehensive empirical formula designed to predict both theoretical temperature and surface roughness. The methodology. The surface roughness and temperature values were evaluated for EN 8, Al 380, SS 316 and SAE 8620 materials using TiAlN coated carbide tool. The TiAlN coating was formed using Physical Vapor Deposition (PVD) Technique. The response surface methodology was used to prepare predictive models. Cutting speed (140 to 340 m/min), feed (0.08 to 0.24 mm/rev) and depth of cut (0.6 to 1.0 mm) was used as input parameters for measuring the performance of all material in terms of surface roughness and cutting temperature. The tool-work thermocouple principle was used to measure the temperature at the chip-tool interface. A Novel Calibration Setup was developed to establish a connection between the electromotive force (EMF) generated during machining and the cutting temperature. Results and Discussion. It is observed that the power required for machining was largely transformed into heat. The highest cutting temperature is recorded when machining of SS 316 followed by SAE 8620, EN 8. However, low temperature is reported during machining of Al 380 and it is mainly governed by the thermal conductivity of the material. The lowest surface roughness is observed in SAE 8620, EN 8 material followed by SS 316 and Al 380. Semi-empirical method and regression model equations show a good agreement with each other. Statistical analysis of nonlinear estimation reveals that the cutting speed, feed, and density of the material have a greater effect on surface roughness, whereas the depth of cut has a greater effect on temperature generation. The study will be very useful for predicting industrial productivity when machining of EN 8, Al 380, SS 316 and SAE 8620 materials with TiAlN-coated carbide tool.
- 19 September 2021
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 21 (4) , 1259-1271
Determination of optimal performance in wire electrical discharge machining of Al/Al2O3/22p composites using response surface methods and grey relational analysis
In this study, wire electrical discharge machining of aluminium matrix composites has been experimentally investigated. A metal matrix composite Al/Al2O3/22 p has been machined at various combinations of machining parameters such as pulse on-time, off-time, wire speed and wire tension. Empirical models have been developed to predict the cutting rate, surface roughness and kerf width of the machined composite material. The models were developed by using the technique of response surface methodology. The experiments were conducted in standard roughing mode by using carefully planned response surface design matrix (central composite design). The model predictions are in good agreement with the experimental results. The R2 values of the proposed cutting rate and kerf width models are above 0.99, where as it is 0.98 for the surface roughness model. The pulse on-time was found to influence cutting rate and surface finish significantly. Kerf width was found to be affected by pulse on-time, off-time, wire speed and wire tension. In addition, a model was developed to correlate the multiple performance characteristic called as grey relational grade and the process parameters. The grey relational grade was significantly affected by pulse on-time and off-time time. The R2 value for the grey relational grade model was 0.94. Optimal parameter setting was determined for the multiple performance characteristic. The improvement in cutting rate was significant with reasonably smooth surfaces and narrow kerf width. However, the surface finish was found to be dominated by the presence of protruding ceramic particles on the machined surfaces.
- 19 September 2021
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 21 (4) , 1259-1271
Determination of optimal performance in wire electrical discharge machining of Al/Al2O3/22p composites using response surface methods and grey relational analysis
In this study, wire electrical discharge machining of aluminium matrix composites has been experimentally investigated. A metal matrix composite Al/Al2O3/22 p has been machined at various combinations of machining parameters such as pulse on-time, off-time, wire speed and wire tension. Empirical models have been developed to predict the cutting rate, surface roughness and kerf width of the machined composite material. The models were developed by using the technique of response surface methodology. The experiments were conducted in standard roughing mode by using carefully planned response surface design matrix (central composite design). The model predictions are in good agreement with the experimental results. The R2 values of the proposed cutting rate and kerf width models are above 0.99, where as it is 0.98 for the surface roughness model. The pulse on-time was found to influence cutting rate and surface finish significantly. Kerf width was found to be affected by pulse on-time, off-time, wire speed and wire tension. In addition, a model was developed to correlate the multiple performance characteristic called as grey relational grade and the process parameters. The grey relational grade was significantly affected by pulse on-time and off-time time. The R2 value for the grey relational grade model was 0.94. Optimal parameter setting was determined for the multiple performance characteristic. The improvement in cutting rate was significant with reasonably smooth surfaces and narrow kerf width. However, the surface finish was found to be dominated by the presence of protruding ceramic particles on the machined surfaces.
- 28 February 2020
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Innovative Technology and Exploring Engineering
- Vol. 4 (9) , 3172-3178
Drilling of Ceramic Reinforced Aluminum Matrix Composite under Minimum Quantity Lubrication using Bio Cutting Fluid
In this study an experimental investigation of effects of cutting parameters on surface roughness during drilling of silicon carbide particulate reinforced aluminium matrix composite material under minimum quantity lubrication (MQL) condition was carried out. Cutting speed , feed rate, flow rate and % SiC in aluminium matrix composites were chosen as cutting parameters. The experimental design adopted for this investigation was the central composite design of response surface methodology. Thirty one readings were taken on VMC machine for MQL condition and the surface roughness measured using Mitutoyo surface tester. Surface roughness values for MQL condition were lower with 30% SiC reinforced aluminium matrix composites when compared to 10 % and 20 % SiC reinforced aluminium matrix composites . As cutting speed increased Ra & Rz value also increased .% SiC was found most significant factor while drilling aluminium matrix composites.
- 28 February 2020
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Innovative Technology and Exploring Engineering
- Vol. 4 (9) , 3172-3178
Drilling of Ceramic Reinforced Aluminum Matrix Composite under Minimum Quantity Lubrication using Bio Cutting Fluid
In this study an experimental investigation of effects of cutting parameters on surface roughness during drilling of silicon carbide particulate reinforced aluminium matrix composite material under minimum quantity lubrication (MQL) condition was carried out. Cutting speed , feed rate, flow rate and % SiC in aluminium matrix composites were chosen as cutting parameters. The experimental design adopted for this investigation was the central composite design of response surface methodology. Thirty one readings were taken on VMC machine for MQL condition and the surface roughness measured using Mitutoyo surface tester. Surface roughness values for MQL condition were lower with 30% SiC reinforced aluminium matrix composites when compared to 10 % and 20 % SiC reinforced aluminium matrix composites . As cutting speed increased Ra & Rz value also increased .% SiC was found most significant factor while drilling aluminium matrix composites.
- 28 February 2020
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Innovative Technology and Exploring Engineering
- Vol. 4 (9) , 3029-3033
Drilling of Ceramic Reinforced Aluminum Matrix Composite under Dry Condition
In this study an experimental investigation of effects of cutting parameters on surface roughness during drilling of silicon carbide particulate reinforced aluminium matrix composite material under dry condition was carried out. Cutting speed , feed rate and % SiC in aluminium matrix composites were chosen as cutting parameters. The experimental design adopted for this investigation was the central composite design of response surface methodology. Thirty one readings were taken on VMC machine for dry condition and the surface roughness measured using Mitutoyo surface tester. Surface roughness values for dry condition were lower with 30% SiC reinforced aluminium matrix composites when compared to 10 % and 20 % SiC reinforced aluminium matrix composites . As cutting speed increased Ra & Rz value also increased .% SiC was found most significant factor while drilling aluminium matrix composites.
- 28 February 2020
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Innovative Technology and Exploring Engineering
- Vol. 4 (9) , 3029-3033
Drilling of Ceramic Reinforced Aluminum Matrix Composite under Dry Condition
In this study an experimental investigation of effects of cutting parameters on surface roughness during drilling of silicon carbide particulate reinforced aluminium matrix composite material under dry condition was carried out. Cutting speed , feed rate and % SiC in aluminium matrix composites were chosen as cutting parameters. The experimental design adopted for this investigation was the central composite design of response surface methodology. Thirty one readings were taken on VMC machine for dry condition and the surface roughness measured using Mitutoyo surface tester. Surface roughness values for dry condition were lower with 30% SiC reinforced aluminium matrix composites when compared to 10 % and 20 % SiC reinforced aluminium matrix composites . As cutting speed increased Ra & Rz value also increased .% SiC was found most significant factor while drilling aluminium matrix composites.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2018, 020009
Comparative investigations into high speed machining of A-B titanium alloy (Ti–6al-4v) under dry and compressed Co2 gas cooling environment
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2018, 020009
Comparative investigations into high speed machining of A-B titanium alloy (Ti–6al-4v) under dry and compressed Co2 gas cooling environment
- Open Access
- 1 January 2018
- Published by Elsevier in Procedia Manufacturing
- Vol. 20, 207-212
Experimental study of non edible vegetable oil as a cutting fluid in machining of M2 Steel using MQL
- 1 January 2018
- Published by Elsevier in Procedia Manufacturing
- Vol. 20, 207-212
Open AccessExperimental study of non edible vegetable oil as a cutting fluid in machining of M2 Steel using MQL