Paula Manica Lazzari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Paula Manica Lazzari has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Américo Campos Filho
Universidade Federal do Rio Grande do Sul, Brasil
13 shared publications - Bruna Manica Lazzari
Civil Engineering Department Pontifical Catholic University of Rio Grande do Sul Porto Alegre Brazil
6 shared publications Alexandre Rodrigues Pacheco
Programa de Pós‐Graduação em Engenharia Civil Universidade Federal do Rio Grande do Sul Porto Alegre Rio Grande do Sul Brazil
4 shared publications- Eric Renã Zavitzki Schimanowski
Department of Civil Engineering, Engineering School, Federal University of Rio Grande do Sul, Porto Alegre, Brazil
3 shared publications Bruna Manica Lazzari
Universidade Federal do Rio Grande do Sul e Pontifícia Universidade Católica do Rio Grande do Sul
2 shared publicationsFrancisco De Paula Simõ Es Lopes Gastal
2 shared publications
Latest Publications
- 20 May 2025
- Published by Springer Nature in Archives of Computational Methods in Engineering
- Vol. 32 (8) , 5187-5269
State‑of‑the‑Art Review of Numerical Simulation of Punching Shear in Slabs
- 20 May 2025
- Published by Springer Nature in Archives of Computational Methods in Engineering
- Vol. 32 (8) , 5187-5269
State‑of‑the‑Art Review of Numerical Simulation of Punching Shear in Slabs
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (6)
Numerical analysis of CFRP laminate-strengthened RC beams with interface modeling considering the bond-slip behavior
Carbon Fiber Reinforced Polymers (CFRP) have emerged as a promising material for structural strengthening, due to their excellent mechanical properties, low weight and, mainly, their non-corrosive nature. The most common application method for CFRP is the Externally Bonded Reinforcement (EBR) technique, which consists of externally bonding the reinforcement material to the surface of a structure using resin, and can be applied in the form of a laminate or sheet. This research numerically analyzed the behavior of reinforced concrete (RC) beams strengthened in flexure with CFRP laminates by the EBR technique, using the Finite Element Method (FEM) through the ANSYS software. This study expands the scope of previous research by adopting CFRP laminates, considering full-scale beams, and investigating different modeling strategies for the concrete-CFRP interface, known as a key region in structural response. Computational modeling of four beams was carried out based on two experimental studies from the literature. The proposed numerical model considered the physical and geometric nonlinearities of the materials involved, with emphasis on the bond behavior at the concrete-CFRP interface through the implementation of contact elements and the Bilinear Cohesive Zone Model. The comparison between numerical and experimental results showed good agreement in terms of load-displacement and load-deformation curves of concrete, reinforcement, and laminate, as well as in the bearing capacity and failure mode, with a maximum difference of 3.27% in the ultimate load. These results demonstrated that the adopted modeling adequately predicts the behavior of beams strengthened in flexure with CFRP laminates, providing support for future parametric studies and contributing to design guidelines and practical applications in the strengthening of RC structures.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (6)
Open AccessNumerical analysis of CFRP laminate-strengthened RC beams with interface modeling considering the bond-slip behavior
Carbon Fiber Reinforced Polymers (CFRP) have emerged as a promising material for structural strengthening, due to their excellent mechanical properties, low weight and, mainly, their non-corrosive nature. The most common application method for CFRP is the Externally Bonded Reinforcement (EBR) technique, which consists of externally bonding the reinforcement material to the surface of a structure using resin, and can be applied in the form of a laminate or sheet. This research numerically analyzed the behavior of reinforced concrete (RC) beams strengthened in flexure with CFRP laminates by the EBR technique, using the Finite Element Method (FEM) through the ANSYS software. This study expands the scope of previous research by adopting CFRP laminates, considering full-scale beams, and investigating different modeling strategies for the concrete-CFRP interface, known as a key region in structural response. Computational modeling of four beams was carried out based on two experimental studies from the literature. The proposed numerical model considered the physical and geometric nonlinearities of the materials involved, with emphasis on the bond behavior at the concrete-CFRP interface through the implementation of contact elements and the Bilinear Cohesive Zone Model. The comparison between numerical and experimental results showed good agreement in terms of load-displacement and load-deformation curves of concrete, reinforcement, and laminate, as well as in the bearing capacity and failure mode, with a maximum difference of 3.27% in the ultimate load. These results demonstrated that the adopted modeling adequately predicts the behavior of beams strengthened in flexure with CFRP laminates, providing support for future parametric studies and contributing to design guidelines and practical applications in the strengthening of RC structures.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18110
Reliability analysis of reinforced concrete slabs according to NBR 6118 considering the lateral confinement
The effect of lateral confinement in reinforced concrete slabs is widely recognized for its ability to increase the supported ultimate load. In this context, this study proposes a reliability analysis of slabs designed according to Brazilian standards, considering or not the phenomenon, with the goal of establishing a comparison between the cases. A numerical model developed in ANSYS software, calibrated from experimental results, was used to determine the slabs' failure loads. The Monte Carlo Simulation Method was employed to obtain the failure probabilities and reliability indexes. Additionally, a parametric study was conducted to understand the main factors influencing the reliability, whether considering lateral confinement or not. The results indicated a significant increase in the reliability of the slabs when lateral confinement was considered, raising the average reliability index from 3.29 to 4.44. The parametric study revealed that the factors influencing the reliability of confined slabs are similar to those obtained when not considering it, as also demonstrated by the strong correlation between the reliability indexes of confined and unconfined slabs.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18110
Open AccessReliability analysis of reinforced concrete slabs according to NBR 6118 considering the lateral confinement
The effect of lateral confinement in reinforced concrete slabs is widely recognized for its ability to increase the supported ultimate load. In this context, this study proposes a reliability analysis of slabs designed according to Brazilian standards, considering or not the phenomenon, with the goal of establishing a comparison between the cases. A numerical model developed in ANSYS software, calibrated from experimental results, was used to determine the slabs' failure loads. The Monte Carlo Simulation Method was employed to obtain the failure probabilities and reliability indexes. Additionally, a parametric study was conducted to understand the main factors influencing the reliability, whether considering lateral confinement or not. The results indicated a significant increase in the reliability of the slabs when lateral confinement was considered, raising the average reliability index from 3.29 to 4.44. The parametric study revealed that the factors influencing the reliability of confined slabs are similar to those obtained when not considering it, as also demonstrated by the strong correlation between the reliability indexes of confined and unconfined slabs.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18102
Bending reinforcement of reinforced concrete beams with alkali-resistant fiberglass textile-reinforced concrete with different surface treatments
Resumo O concreto têxtil surge como uma alternativa para o reforço de estruturas de concreto armado. Porém, por ser um material relativamente novo, inexiste ainda um órgão ou norma regulamentadora que uniformize os processos de fabricação e de aplicação do material, o que gera diferenças significativas quanto às suas características e propriedades. Sob esta perspectiva, este estudo busca avaliar experimentalmente o desempenho mecânico do concreto têxtil ao ser aplicado como reforço de vigas em concreto armado submetidas ao ensaio de flexão a quatro pontos, utilizando o têxtil de fibra de vidro álcali-resistente de produção brasileira TEXIGLASS AR-360-RA-04. De caráter exploratório, o programa experimental é composto por quatorze vigas reforçadas e uma viga testemunho de seção retangular (120 mm de largura, 200 mm de altura e 1500 mm de comprimento), totalizando quinze vigas. Como variáveis, investigam-se a resistência de ligação na interface têxtil-matriz a partir do (a) tipo de matriz (argamassa polimérica industrializada ou argamassa autoadensável) e do (b) tratamento superficial do têxtil em quatro configurações: têxtil sem revestimento (SR), revestido com epóxi (E), totalmente revestido com epóxi e areia (EA) ou totalmente revestido com epóxi, mas com areia somente nas extremidades (EAP). A partir dos resultados, verificou-se principalmente que: todas as vigas reforçadas apresentaram aumentos da (a) capacidade resistente, (b) ductilidade e (c) tenacidade. Apesar da grande variabilidade de resultados, a técnica de revestimento nos exemplares dos têxteis EAP se mostrou promissora.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18102
Open AccessBending reinforcement of reinforced concrete beams with alkali-resistant fiberglass textile-reinforced concrete with different surface treatments
Resumo O concreto têxtil surge como uma alternativa para o reforço de estruturas de concreto armado. Porém, por ser um material relativamente novo, inexiste ainda um órgão ou norma regulamentadora que uniformize os processos de fabricação e de aplicação do material, o que gera diferenças significativas quanto às suas características e propriedades. Sob esta perspectiva, este estudo busca avaliar experimentalmente o desempenho mecânico do concreto têxtil ao ser aplicado como reforço de vigas em concreto armado submetidas ao ensaio de flexão a quatro pontos, utilizando o têxtil de fibra de vidro álcali-resistente de produção brasileira TEXIGLASS AR-360-RA-04. De caráter exploratório, o programa experimental é composto por quatorze vigas reforçadas e uma viga testemunho de seção retangular (120 mm de largura, 200 mm de altura e 1500 mm de comprimento), totalizando quinze vigas. Como variáveis, investigam-se a resistência de ligação na interface têxtil-matriz a partir do (a) tipo de matriz (argamassa polimérica industrializada ou argamassa autoadensável) e do (b) tratamento superficial do têxtil em quatro configurações: têxtil sem revestimento (SR), revestido com epóxi (E), totalmente revestido com epóxi e areia (EA) ou totalmente revestido com epóxi, mas com areia somente nas extremidades (EAP). A partir dos resultados, verificou-se principalmente que: todas as vigas reforçadas apresentaram aumentos da (a) capacidade resistente, (b) ductilidade e (c) tenacidade. Apesar da grande variabilidade de resultados, a técnica de revestimento nos exemplares dos têxteis EAP se mostrou promissora.
- 27 November 2024
- Published by Wiley in Structural Concrete
- Vol. 26 (4) , 4981-5000
An investigation of punching shear in flat slabs with spherical voids using the finite element method
Flat slabs with voids allow for the reduction of the structure's self‐weight by removing concrete from regions of the cross‐section subjected to low stresses. However, the presence of voids impacts the behavior of these structures, especially under punching loads, and few studies have assessed the impact of different parameters on voided slabs. Thus, this study validated numerical modeling developed in the ANSYS software, using the finite element method, based on 17 experimental slabs from the literature. The numerical simulation indicated a good approximation of the deformation behavior of the structure, as well as a similar mode of failure. Once validated, the model evaluated different parameters in spherical voided slabs. The results showed significant impacts on the rupture load, ductility, or stiffness when varying the void's presence, position, diameter, concrete properties, slab thickness, flexural reinforcement ratio, and shear reinforcement. In voided slabs, the critical situation occurred when inserting the spheres in a region very close to the column, which reduced the rupture load by about half, when compared to a solid slab.
- 27 November 2024
- Published by Wiley in Structural Concrete
- Vol. 26 (4) , 4981-5000
An investigation of punching shear in flat slabs with spherical voids using the finite element method
Flat slabs with voids allow for the reduction of the structure's self‐weight by removing concrete from regions of the cross‐section subjected to low stresses. However, the presence of voids impacts the behavior of these structures, especially under punching loads, and few studies have assessed the impact of different parameters on voided slabs. Thus, this study validated numerical modeling developed in the ANSYS software, using the finite element method, based on 17 experimental slabs from the literature. The numerical simulation indicated a good approximation of the deformation behavior of the structure, as well as a similar mode of failure. Once validated, the model evaluated different parameters in spherical voided slabs. The results showed significant impacts on the rupture load, ductility, or stiffness when varying the void's presence, position, diameter, concrete properties, slab thickness, flexural reinforcement ratio, and shear reinforcement. In voided slabs, the critical situation occurred when inserting the spheres in a region very close to the column, which reduced the rupture load by about half, when compared to a solid slab.
- 11 October 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 97
An experimental study on RC beams externally strengthened by anchored CFRP sheets monitored by Digital Image Correlation
- 11 October 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 97
An experimental study on RC beams externally strengthened by anchored CFRP sheets monitored by Digital Image Correlation
- 26 March 2024
- Published by Wiley in Structural Concrete
- Vol. 25 (5) , 3164-3187
Study via the finite element method of the behavior of deck joints in a bridge composed of precast concrete segments
There is a demand for research to better understand the structural performance of segmental bridge joints. In this context, the main objective of this work is to present a 3D numerical modeling using the Finite Element Method (FEM) to physically simulate the behavior of concrete joints in a segmental concrete bridge. The analysis was conducted using the design of a real bridge, and the structure studied was the main span of the New Guaíba Bridge, located in Porto Alegre, RS, Brazil. The modeling was implemented using ANSYS software, version 21.2. The simulation considers a complete model of the span to provide a more realistic determination of the joint openings and the stress distributions in the elements. It is crucial to emphasize that the results obtained from the model do not reproduce the observed behavior of the studied bridge. The analysis considered only one span with simplified boundary conditions and higher loads than those typically adopted in usual design procedures.
- 26 March 2024
- Published by Wiley in Structural Concrete
- Vol. 25 (5) , 3164-3187
Study via the finite element method of the behavior of deck joints in a bridge composed of precast concrete segments
There is a demand for research to better understand the structural performance of segmental bridge joints. In this context, the main objective of this work is to present a 3D numerical modeling using the Finite Element Method (FEM) to physically simulate the behavior of concrete joints in a segmental concrete bridge. The analysis was conducted using the design of a real bridge, and the structure studied was the main span of the New Guaíba Bridge, located in Porto Alegre, RS, Brazil. The modeling was implemented using ANSYS software, version 21.2. The simulation considers a complete model of the span to provide a more realistic determination of the joint openings and the stress distributions in the elements. It is crucial to emphasize that the results obtained from the model do not reproduce the observed behavior of the studied bridge. The analysis considered only one span with simplified boundary conditions and higher loads than those typically adopted in usual design procedures.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (3) , e17316
Numerical simulation of punching shear in flat slabs with spherical voids subjected to symmetric and asymmetric loadings
Using hollow spherical voids within slabs brings the already-known advantages of conventional flat slab systems with the weight reduction caused by removing concrete from less stressed structure regions. However, it is necessary to carefully assess the punching shear phenomenon, mainly when unbalanced loads are applied. Thus, a numerical simulation using the Finite Element Method was developed, and validated with experimental data from four slabs, one solid, and three slabs with spherical voids. The results demonstrated good approximations when unbalanced loads were considered for load-displacement behavior, load-strain in concrete and reinforcements, and failure surface. Overall, a decrease in ultimate load, stiffness, and load at the first crack was identified when spherical voids were used.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (3) , e17316
Open AccessNumerical simulation of punching shear in flat slabs with spherical voids subjected to symmetric and asymmetric loadings
Using hollow spherical voids within slabs brings the already-known advantages of conventional flat slab systems with the weight reduction caused by removing concrete from less stressed structure regions. However, it is necessary to carefully assess the punching shear phenomenon, mainly when unbalanced loads are applied. Thus, a numerical simulation using the Finite Element Method was developed, and validated with experimental data from four slabs, one solid, and three slabs with spherical voids. The results demonstrated good approximations when unbalanced loads were considered for load-displacement behavior, load-strain in concrete and reinforcements, and failure surface. Overall, a decrease in ultimate load, stiffness, and load at the first crack was identified when spherical voids were used.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (3) , e17308
Investigation of an alternative system for monitoring strains in reinforced concrete structures
Concrete is the second most applied resource in the world (water is the first) and is massively applied by designers, builders, construction workers, and others involved in construction processes. This considerable acceptance of such material worldwide and its increasing use in Brazil is related to several aspects, such as the availability of its components, ease of use, and cost efficiency [1 1 T. Andrade, “Tópicos sobre durabilidade do concreto,” in Concreto: Ensino, Pesquisa e Realizações, G. C. Isaia, Ed., São Paulo, Brazil: IBRACON, 2005, ch. 25, vol. 1, pp. 753-792. ]. New methods and techniques in engineering allied to technological advances in concrete have allowed the construction of slender and bolder structures [2 2 F. A. Torrico, “Análise teórica e experimental do comportamento de pilares esbeltos de concreto de alta resistência, considerando a ductilidade,” Ph.D. dissertation, Escola Eng. São Carlos, Univ. São Paulo, São Carlos, Brazil, 2010. ]. However, due to the variations that can occur in the properties of concrete, which are a function of many variables and conditions, the development of methods to verify the performance of concrete elements becomes increasingly relevant [3 3 A. Lorenzi, J. L. Campagnolo, and L. C. P. Silva Fo., “Application of artificial neural network for interpreting ultrasonic readings of concrete,” Int. J. Mater. Prod. Technol., vol. 26, pp. 57-70, Feb. 2006. ].
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (3) , e17308
Open AccessInvestigation of an alternative system for monitoring strains in reinforced concrete structures
Concrete is the second most applied resource in the world (water is the first) and is massively applied by designers, builders, construction workers, and others involved in construction processes. This considerable acceptance of such material worldwide and its increasing use in Brazil is related to several aspects, such as the availability of its components, ease of use, and cost efficiency [1 1 T. Andrade, “Tópicos sobre durabilidade do concreto,” in Concreto: Ensino, Pesquisa e Realizações, G. C. Isaia, Ed., São Paulo, Brazil: IBRACON, 2005, ch. 25, vol. 1, pp. 753-792. ]. New methods and techniques in engineering allied to technological advances in concrete have allowed the construction of slender and bolder structures [2 2 F. A. Torrico, “Análise teórica e experimental do comportamento de pilares esbeltos de concreto de alta resistência, considerando a ductilidade,” Ph.D. dissertation, Escola Eng. São Carlos, Univ. São Paulo, São Carlos, Brazil, 2010. ]. However, due to the variations that can occur in the properties of concrete, which are a function of many variables and conditions, the development of methods to verify the performance of concrete elements becomes increasingly relevant [3 3 A. Lorenzi, J. L. Campagnolo, and L. C. P. Silva Fo., “Application of artificial neural network for interpreting ultrasonic readings of concrete,” Int. J. Mater. Prod. Technol., vol. 26, pp. 57-70, Feb. 2006. ].
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 16 (3) , e16304
Identification of the failure modes of CFRP shear-strengthened reinforced concrete beams by the finite element method
A reduction in the performance of concrete structures tends to occur along their lifespan because of many factors and, eventually, they may present deficient strength to resist their design forces. Several strengthening methods can be applied to structural elements, such as externally bonded steel plates or fiber-based composite materials. The latter consists of the application of composite materials known as Fiber Reinforced Polymer (FRP), which present properties of low density, high tensile strength, corrosion resistance, high fatigue resistance, and high-impact resistance. Among the types of composite materials, carbon fiber reinforced polymers (CFRP) are the most used for structural strengthening since carbon fibers offer the best mechanical properties. Therefore, according to Dias [1 1 S. J. E. Dias, “Investigação experimental e analítica no reforço ao corte de vigas de betão armado com a técnica da inserção de laminados de CFRP,” Ph.D. dissertation, Esc. Eng., Univ. Minho, Guimarães, Portugal, 2008. ] and Mhanna et al. [2 2 H. H. Mhanna, R. A. Hawileh, and J. A. Abdalla, “Shear behavior of RC T-beams externally strengthened with anchored high modulus carbon fiber-reinforced polymer (CFRP) laminates,” Compos. Struct., vol. 272, p. 114198, May 2021, http://dx.doi.org/10.1016/j.compstruct.2021.114198. http://dx.doi.org/10.1016/j.compstruct.2... ], significant increases in the load capacity of structural elements are obtained through a small amount of strengthening.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 16 (3) , e16304
Open AccessIdentification of the failure modes of CFRP shear-strengthened reinforced concrete beams by the finite element method
A reduction in the performance of concrete structures tends to occur along their lifespan because of many factors and, eventually, they may present deficient strength to resist their design forces. Several strengthening methods can be applied to structural elements, such as externally bonded steel plates or fiber-based composite materials. The latter consists of the application of composite materials known as Fiber Reinforced Polymer (FRP), which present properties of low density, high tensile strength, corrosion resistance, high fatigue resistance, and high-impact resistance. Among the types of composite materials, carbon fiber reinforced polymers (CFRP) are the most used for structural strengthening since carbon fibers offer the best mechanical properties. Therefore, according to Dias [1 1 S. J. E. Dias, “Investigação experimental e analítica no reforço ao corte de vigas de betão armado com a técnica da inserção de laminados de CFRP,” Ph.D. dissertation, Esc. Eng., Univ. Minho, Guimarães, Portugal, 2008. ] and Mhanna et al. [2 2 H. H. Mhanna, R. A. Hawileh, and J. A. Abdalla, “Shear behavior of RC T-beams externally strengthened with anchored high modulus carbon fiber-reinforced polymer (CFRP) laminates,” Compos. Struct., vol. 272, p. 114198, May 2021, http://dx.doi.org/10.1016/j.compstruct.2021.114198. http://dx.doi.org/10.1016/j.compstruct.2... ], significant increases in the load capacity of structural elements are obtained through a small amount of strengthening.