YSYuta Sunami

Yuta Sunami

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yuta Sunami has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Clarification of the Transfer Phenomenon that a Silicone Rubber Roller Exerts on a Film Surface

    by Wataru Shimoji, Yuta Sunami, Minoru Oka, Yo Hinohara

    Rubber rollers are used in various film production processes due to their high elasticity. Among them, silicone rubber excels in heat resistance and detachability and is also used as a film-forming nip roll, taking advantage of these characteristics. However, it is extremely difficult to control the surface roughness of rubber compared to steel rollers, and the unevenness and light characteristics (transmittance) of the rubber are greatly changed by the transfer. Therefore, in this study, film formation experiments were carried out with the aim of clarifying the transfer phenomenon from the silicone rubber roller to the film formation film. Then, the transfer rate to the film was analyzed from the results of measuring the roughness of the silicone rubber surface and the film surface.

  • Effect of Circumferential Slip on Scratch Occurrence under Different Winding Conditions

    by Yuta Sasamoto, Toshimitu Kannda, Yuta Sunami

    A long, thin, continuous, flexible medium are commonly referred to as a web. Webs are often used as substrates in high-performance flexible devices. Roll-to-roll printed electronics production is expected to be the production method for these devices. However, there are still many problems. If the winding conditions are inappropriate, winding defects such as abrasions can occur. Slippage causes abrasion of the web, which damages the printed material. When the web is scratched, it loses its product value as well as other winding defects. In this study, the effects of winding speed and tension on the occurrence of slippage were investigated by varying the tension and speed in three steps. The modified Hakiel model proposed by Hashimoto et al. was used to compare the relationship between radial stress, interlayer air entrainment, interlayer frictional force and slip in the rolls with misalignment. As a result, it was confirmed that the amount of misalignment was the largest under the winding condition where the radial stress was the lowest. The amount of air entrainment increases under the condition of low internal stress. It is thought that the amount of misalignment increases because the frictional force between the web layers decreases.

  • Effect of the Change of Micro Spike that a Wing has of Dragonfly gives to Aerodynamic at the Gliding Flight

    by Sarato Nakamura, Yuta Sunami

    In recent years, attention has been paid to the activity of Unmanned Aerial vehicles such as disaster site surveys and home delivery using drones. However, the current UAV cannot fly for a long time because of the influence of viscosity. The application of biomimetics is being considered to improve the performance of UAVs. Dragonflies are known to have high flight performance among flying organisms, and the fine structure existing in the wings of dragonflies is considered to be important. There are some types that can fly over 7100 km by using gliding flight. In this paper, we focused on the micro spike of about 100 μm on the wing surface of the dragonfly and performed computational fluid dynamics on changes in spike height using ANSYS FLUENT. As a result, It was confirmed that increasing the spike reduces the drag coefficient. It is thought that this is because the flow velocity is reduced by the micro spikes, which suppresses the growth of the vortex and reduces the pressure difference. From the above, it was considered that the pressure drag was reduced by the micro spikes. This consideration could be confirmed from the analysis results.

  • Development and Characterization of Pressure-Sensitive Nano-Sheet for Thermo-Fluid Measurement

    by Yusaku Abe, Riki Orimo, Yuri Hiraiwa, Yosuke Okamura, Yuta Sunami, Yu Matsuda

    Pressure measurement method using pressure-sensitive paint (PSP) is gathering attention in the thermal and fluids engineering because it is possible to measure the pressure distribution on a model of interest. However, air brush coating, which is widely used as a method of applying PSP to a surface, has a problem that the pressure sensitivity depends on the skill of the person applying it. Therefore, there is a need to the development of a novel PSP application method. We have proposed pressure-sensitive nano-sheet (PSNS) based on fabrication methods of nano-sheets. In this study, we investigated the applicability of PSNS to pressure measurement. The pressure distribution induced by impinging jet was successfully measured by PSNS.

  • Fabrication of Porous Nanosheets by Continuous Nanoimprinting Lithography on Polymer Ultrathin Films

    by Kanna Matsumoto, Yuta Sunami

    We focused on producing porous nanosheets by using micropore processing on polymer ultrathin films (nanosheets), which are expected to be applied in the medical field. Nanosheets exhibit features such as high flexibility and high adhesiveness when the film thickness is 100 nm or less. In order to enable mass production of porous nanosheets, we adopted the roll nanoimprint method, which enables continuous processing. However, little research has been done on roll nanoimprint processing on nanosheets. In order to increase the transfer speed of the roll nanoimprint method and mass-produce porous nanosheets, it is necessary to establish a micropore processing method during low-speed transfer. Therefore, the production conditions for low-speed transfer using a calendar machine were examined while comparing with the micropore processing using a press machine. At that time, the type of nickel mold, the nanosheet material to be processed, and the clearance between the rollers were changed to perform microfabrication to produce a porous nanosheet. After preparation, observation was performed and evaluation was performed based on the presence or absence of micropores. As a result, it was found that the nanosheet material to be processed and the clearance affect the micropore processing.

  • Open Access

    Pressure-Sensitive Nano-Sheet for Optical Pressure Measurement

    by Yu Matsuda, Riki Orimo, Yusaku Abe, Yuri Hiraiwa, Yosuke Okamura, Yuta Sunami

    Pressure-Sensitive Paint (PSP) is a powerful measurement technique to obtain pressure distribution on a model of interest by measuring the emission intensity of the PSP coating with a camera. Since a PSP coating is prepared by applying a solution containing an organic solvent, generally, by sprayer, the properties such as the pressure- and the temperature-sensitivity depends on the skill of the person applying it. This fabrication process is one of the barriers to use of the PSP technique because of the legal restrictions on the use of organic solvents. Thus, a sticker-like PSP coating is useful because it does not require the use of organic solvent and the applying skill. In this study, we have fabricated freestanding Pressure-Sensitive Nano-Sheet (PSNS) by a sacrificial layer process using a spin-coating method. We employed Pt(II) meso-tetra(pentafluorophenyl)porphine (PtTFPP) as a pressure-sensitive dye and poly(1-trimethylsilyl-propyne) (PTMSP) and poly(L-lactic acid) (PLLA) as a polymer binder; thus, the PSNS samples based on PTMSP and PLLA were prepared. The pressure- and the temperature-sensitivity, the lifetime of the luminescence, and the quantum yield of the fabricated PSNS have been investigated. The pressure-sensitivity of PTMSP-based PSNS is higher than that of PLLA-based PSNS. Conversely, the quantum yield of PLLA-based PSNS is higher than that of PTMSP-based PSNS.


  • EFFECTS OF INJECTION SPEED ON MECHANICAL PROPERTIES IN HIGH-PRESSURE DIE CASTING OF MG-RE ALLOY

    by Yuki Kashiwabara, Mohd Danial Ibrahim, Lidyana Binti Roslan, Hitoshi Watanabe, Yuta Sunami, Japan Kyokuto Die-Casting Co

    In this study, in order to clarify the unknown physical properties of the Mg-Al-Th-RE alloy, the relationship between the injection conditions and the internal porosities and the mechanical properties exerted by the solidification microstructure were investigated. The obtained cast samples were investigated using X-ray CT internal measurements, tensile tests, Vickers hardness tests and solidification microstructure observations. The flow simulation and the X-ray CT analysis results showed that the porosity volume increased as the injection speed increases. The higher injection speed also affected the metal microstructure to become denser, which leads to a higher material strength and hardness. The eutectic phases quickly formed because of the shorter filled and cooled time. Therefore, the growth of the primary phase a-Mg was suppressed. On the other hand, it was considered that the material strength and hardness were greatly reduced by the coarse primary phase.

  • Evaluation of Physical Properties and Internal Stress Analysis in Winding Roll

    by Takeshi Nishida, Hiromu Hashimoto, Yuta Sunami

    In recent years, research and development of flexible devices such as film capacitors, organic thin film solar cells, and lithium ion secondary batteries using thin and flexible plastic films as substrates have been actively conducted. However, flexible devices are rarely available in the general market. One of the reasons is that it is not suitable for mass production because many processes are performed separately during device fabrication. Therefore, roll-to-roll printed electronics (hereinafter referred to as R2RPE) production method is mentioned as one of the methods for mass producing these flexible devices. In addition, at the last winding section of this process, storage of long plastic films can be reduced in a roll shape, and storage space can be reduced, and a large amount of products can be transported at one time, thus significantly improving transport efficiency. Therefore, the winding process is very important process for mass production of flexible devices. There are two main problems that occur in winding rolls. It is a phenomenon called slippage causing slippage in the axial direction between roll layers, and additionally a phenomenon called wrinkles that generates wrinkles inside the roll. It is reported that these problems are affected by the state of internal stress generated in the winding roll. In the roll, internal stress may change from the time of winding due to changes in the surrounding environment such as temperature and humidity during storage and transport, and wrinkles may not occur immediately after winding. Therefore, the prediction and prevention method of the failure by the change of the surrounding environment which occurs frequently at the time of transportation becomes an extremely important technical subject. Although these have been eliminated by Hashimoto et al., This is not the case when placed on thin film. Therefore, the Young's modulus and linear expansion coefficient in each direction, which are physical properties necessary for theoretical analysis of the internal stress of the take-up roll, were measured, and the roll was actually heated for 12 hours to compare changes in internal stress of the roll with theoretical values.