George A. Jackson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
George A. Jackson has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Hao Chen
Department of Mechanical, Materials and Manufacturing Engineering, Faculty of Science and Engineering, University of Nottingham Ningbo China, Ningbo, China
3 shared publications D. Graham McCartney
University of Nottingham
2 shared publicationsWei Sun
University of Nottingham
2 shared publications- David Graham McCartney
Department of Mechanical Engineering, University College London, London WC1E 7JE, UK
1 shared publication K.T. Voisey
1 shared publicationRichard A. Jahnke
Skidaway Institute of Oceanography
1 shared publication
Latest Publications
- 5 July 2017
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 26 (6) , 1222-1238
An Overview of Using Small Punch Testing for Mechanical Characterization of MCrAlY Bond Coats
- 5 July 2017
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 26 (6) , 1222-1238
An Overview of Using Small Punch Testing for Mechanical Characterization of MCrAlY Bond Coats
- 1 April 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 734, 37-48
The High Temperature Creep Properties of a Thermally Sprayed CoNiCrAlY Coating via Small Punch Creep Testing
Thermal barrier coatings (TBC’s) protect superalloy components from excessively high temperatures in gas turbines. TBC’s comprise of a ceramic top coat, a metallic bond coat and a thermally grown oxide (TGO). The creep behaviour of the MCrAlY bond coat, which is sensitive to the composition and the method of deposition, has a significant effect on the life of the TBC. High velocity oxy-fuel (HVOF) thermal spraying is a popular deposition method for MCrAlY bond coats however the creep properties of HVOF MCrAlY coatings are not well documented. The creep behaviour of a HVOF thermally sprayed CoNiCrAlY coating has been determined by small punch creep (SPC) testing. Tests were conducted between an equivalent uniaxial stress range of 37-80 MPa at 750 °C on two different SPC rigs and between 30-49 MPa at 850 °C on a single SPC rig. The measured steady-state creep deformation rates at 750 °C were consistent across the two rigs. A comparison with previous work demonstrated that the creep behaviour of HVOF CoNiCrAlY coatings is not sensitive to the manufacturing variability associated with HVOF thermal spraying. The CoNiCrAlY coating exhibited typical SPC deformation at 750 °C. At 850 °C the CoNiCrAlY coating showed significantly different creep behaviour which could be attributed to the onset of superplasticity.
- 1 April 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 734, 37-48
The High Temperature Creep Properties of a Thermally Sprayed CoNiCrAlY Coating via Small Punch Creep Testing
Thermal barrier coatings (TBC’s) protect superalloy components from excessively high temperatures in gas turbines. TBC’s comprise of a ceramic top coat, a metallic bond coat and a thermally grown oxide (TGO). The creep behaviour of the MCrAlY bond coat, which is sensitive to the composition and the method of deposition, has a significant effect on the life of the TBC. High velocity oxy-fuel (HVOF) thermal spraying is a popular deposition method for MCrAlY bond coats however the creep properties of HVOF MCrAlY coatings are not well documented. The creep behaviour of a HVOF thermally sprayed CoNiCrAlY coating has been determined by small punch creep (SPC) testing. Tests were conducted between an equivalent uniaxial stress range of 37-80 MPa at 750 °C on two different SPC rigs and between 30-49 MPa at 850 °C on a single SPC rig. The measured steady-state creep deformation rates at 750 °C were consistent across the two rigs. A comparison with previous work demonstrated that the creep behaviour of HVOF CoNiCrAlY coatings is not sensitive to the manufacturing variability associated with HVOF thermal spraying. The CoNiCrAlY coating exhibited typical SPC deformation at 750 °C. At 850 °C the CoNiCrAlY coating showed significantly different creep behaviour which could be attributed to the onset of superplasticity.
- 1 April 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 734, 144-155
The Application of the Small Punch Tensile Test to Evaluate the Ductile to Brittle Transition of a Thermally Sprayed CoNiCrAlY Coating
Thermally sprayed MCrAlY bond coats are important elements of thermal barrier coating (TBC) systems which are applied to the surface of gas turbine components to protect them in high temperature environments. Knowledge of their mechanical properties is essential in preventing TBC failure which can have catastrophic consequences. However, limited data on modulus, strength and ductility are available for such coatings. In this work, the ductile to brittle transition behaviour of a CoNiCrAlY coating has been investigated via the small punch tensile test (SPTT). Displacement controlled tests were carried out on free standing coatings at room temperature (RT) and between 400-750 °C at a rate of 1 μms-1. At low temperatures there was evidence of elastic-brittle behaviour and at high temperatures there was clear evidence of yielding and plastic deformation. The ductile to brittle transition temperature was found to be between 500-750 °C. The yield stress ranged from 1000-1500 MPa below 600 °C to less than 500 MPa above 650 °C. The elastic modulus was found to be approximately 200-230 GPa at 500 °C and 55 GPa above 700 °C. At room temperature the fracture surface showed flat, smooth features indicating brittle failure whereas at 700 °C there was evidence of ductile tearing.
- 1 April 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 734, 144-155
The Application of the Small Punch Tensile Test to Evaluate the Ductile to Brittle Transition of a Thermally Sprayed CoNiCrAlY Coating
Thermally sprayed MCrAlY bond coats are important elements of thermal barrier coating (TBC) systems which are applied to the surface of gas turbine components to protect them in high temperature environments. Knowledge of their mechanical properties is essential in preventing TBC failure which can have catastrophic consequences. However, limited data on modulus, strength and ductility are available for such coatings. In this work, the ductile to brittle transition behaviour of a CoNiCrAlY coating has been investigated via the small punch tensile test (SPTT). Displacement controlled tests were carried out on free standing coatings at room temperature (RT) and between 400-750 °C at a rate of 1 μms-1. At low temperatures there was evidence of elastic-brittle behaviour and at high temperatures there was clear evidence of yielding and plastic deformation. The ductile to brittle transition temperature was found to be between 500-750 °C. The yield stress ranged from 1000-1500 MPa below 600 °C to less than 500 MPa above 650 °C. The elastic modulus was found to be approximately 200-230 GPa at 500 °C and 55 GPa above 700 °C. At room temperature the fracture surface showed flat, smooth features indicating brittle failure whereas at 700 °C there was evidence of ductile tearing.
- 1 April 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 291, 34-42
Modelling and experimental study on β-phase depletion behaviour of HVOF sprayed free-standing CoNiCrAlY coatings during oxidation
- 1 April 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 291, 34-42
Modelling and experimental study on β-phase depletion behaviour of HVOF sprayed free-standing CoNiCrAlY coatings during oxidation
- 1 January 1992
- Published by Springer Nature
- p. 295-307
The Spatial Distribution of Sea Floor Oxygen Consumption in The Atlantic and Pacific Oceans
- 1 January 1992
- Published by Springer Nature
- p. 295-307
The Spatial Distribution of Sea Floor Oxygen Consumption in The Atlantic and Pacific Oceans