Horia Constantinescu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Horia Constantinescu has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Gyorgy Thalmaier
Faculty of Materials and Environmental Engineering, Technical University of Cluj-Napoca, 103–105 Muncii Boulevard, 400641 Cluj-Napoca, Romania
3 shared publications O. Gherman
3 shared publications- Traian-Nicu Toader
Department of Structures, Faculty of Civil Engineering, Technical University of Cluj-Napoca, Str. Constantin Daicoviciu 15, 400020 Cluj-Napoca, Romania
3 shared publications - Anca-Andreea Balog
Faculty of Civil Engineering, Technical University of Cluj-Napoca, 28 Memorandumului Street, 400114 Cluj-Napoca, Romania
2 shared publications - Anca-Andreea Balog
Technical University of Cluj Napoca
2 shared publications - Andrei Ceclan
Energy Transition Research Center (EnTReC), Technical University of Cluj-Napoca, 400114 Cluj-Napoca, Romania
2 shared publications
Latest Publications
- Open Access
Structural Design and Technology of Pocket Foundations for Long Precast Concrete Columns in Seismic Areas
The connection between a prefabricated reinforced concrete column and a pocket foundation is a case treated from a general perspective in the European Standard named EN 1992-1-1 (EC2), and when the structural engineer deals with the dimensioning or verification of the connection, he must tackle several unknowns. The present work aims to fill in the missing information by presenting detailed calculation models based on the strut-and-tie method for four widely used pocket foundations: a pedestal pocket foundation with smooth, rough or keyed internal walls and a pad foundation with a pocket possessing keyed internal walls. In establishing the strut-and-tie models and writing the equation for the internal forces, we consider several standards (EC2, NBR 9062 and DIN 1045-1), good practices (from Austria, England, Germany and Romania) and numerous experimental and numerical investigations. Additionally, detailed design prescriptions applicable to seismic areas are given. This manuscript covers a wide range of design and technology aspects necessary for designing and building columns connected with pocket foundations, information for which is shown only in fragmented form or partially in other publications. Afterward, as a case study, a pocket foundation is designed in all four variations, with the structural design particularities, similitudes and differences being pointed out. Finally, to conclude, we mention the advantages and disadvantages of pocket foundations with respect to the type of internal wall surface used. Quantifiable data based on the case study undertaken are available.
Open AccessStructural Design and Technology of Pocket Foundations for Long Precast Concrete Columns in Seismic Areas
The connection between a prefabricated reinforced concrete column and a pocket foundation is a case treated from a general perspective in the European Standard named EN 1992-1-1 (EC2), and when the structural engineer deals with the dimensioning or verification of the connection, he must tackle several unknowns. The present work aims to fill in the missing information by presenting detailed calculation models based on the strut-and-tie method for four widely used pocket foundations: a pedestal pocket foundation with smooth, rough or keyed internal walls and a pad foundation with a pocket possessing keyed internal walls. In establishing the strut-and-tie models and writing the equation for the internal forces, we consider several standards (EC2, NBR 9062 and DIN 1045-1), good practices (from Austria, England, Germany and Romania) and numerous experimental and numerical investigations. Additionally, detailed design prescriptions applicable to seismic areas are given. This manuscript covers a wide range of design and technology aspects necessary for designing and building columns connected with pocket foundations, information for which is shown only in fragmented form or partially in other publications. Afterward, as a case study, a pocket foundation is designed in all four variations, with the structural design particularities, similitudes and differences being pointed out. Finally, to conclude, we mention the advantages and disadvantages of pocket foundations with respect to the type of internal wall surface used. Quantifiable data based on the case study undertaken are available.
- Open Access
- 27 September 2024
- Published by MDPI AG in Preprints.org
Structural Design and Technology of Pocket Foundations for Long Precast Concrete Columns in Seismic Areas
The connection between a prefabricated reinforced concrete column and a pocket foundation is a case treated from a general perspective in the European Standard named EN 1992-1-1, and when the structural engineer deals with the dimensioning or verification of the connection, he tackles several unknowns. The present work aims to fill in the missing information by presenting detailed calculation models based on the strut-and-tie method for 4 of the widely used pocket foundations: pedestal pocket foundation with smooth, rough or keyed internal walls, and pad foundation with pocket possessing keyed internal walls. Additionally, detailed design prescriptions applicable to seismic areas are given. Afterwards, as a case study, a pocket foundation is designed in all 4 variations, having the structural design particularities, similitudes and differences pointed out. Finally, to conclude the advantages and disadvantages are mentioned for pocket foundations in respect to the type of internal wall surface used. Quantifiable data based on the case study undertaken is available.
- 27 September 2024
- Published by MDPI AG in Preprints.org
Open AccessStructural Design and Technology of Pocket Foundations for Long Precast Concrete Columns in Seismic Areas
The connection between a prefabricated reinforced concrete column and a pocket foundation is a case treated from a general perspective in the European Standard named EN 1992-1-1, and when the structural engineer deals with the dimensioning or verification of the connection, he tackles several unknowns. The present work aims to fill in the missing information by presenting detailed calculation models based on the strut-and-tie method for 4 of the widely used pocket foundations: pedestal pocket foundation with smooth, rough or keyed internal walls, and pad foundation with pocket possessing keyed internal walls. Additionally, detailed design prescriptions applicable to seismic areas are given. Afterwards, as a case study, a pocket foundation is designed in all 4 variations, having the structural design particularities, similitudes and differences pointed out. Finally, to conclude the advantages and disadvantages are mentioned for pocket foundations in respect to the type of internal wall surface used. Quantifiable data based on the case study undertaken is available.
- Open Access
- 7 March 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (3) , 165
Coniferous Trees as Bioinspiration for Designing Long Reinforced Prestressed Concrete Columns
This article contains the results of identifying the potential of coniferous trees to act as bioinspiration for the structural design of columns in single-story warehouses subjected to high wind velocity and severe seismic action. This study starts by analyzing the biomechanics of coniferous trees, continues with an abstraction of the relevant features, and ends with the transfer of a design methodology for long reinforced and prestressed concrete columns. To verify the applicability and validity of the mathematical relationships extracted from the bibliographic study to characterize the biomechanics of coniferous trees, a study site is conducted for Norway spruce trees felled by the wind in the Bilbor area. The design methodology for long reinforced and prestressed concrete columns bioinspired by the Norway spruce trees is experimentally validated using two case studies. The first case study deals with the effect of centric prestressing on long concrete columns, and the second on the influence of the walnut shell powder on the adhesion of the reinforcement in concrete. The case studies presented aim to transfer some characteristics from trees to reinforced concrete to improve the performance of long columns under horizontal forces. The results obtained indicate a good approximation of the trees’ structural behavior for this site and for ones investigated by other researchers in different forests.
- 7 March 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (3) , 165
Open AccessConiferous Trees as Bioinspiration for Designing Long Reinforced Prestressed Concrete Columns
This article contains the results of identifying the potential of coniferous trees to act as bioinspiration for the structural design of columns in single-story warehouses subjected to high wind velocity and severe seismic action. This study starts by analyzing the biomechanics of coniferous trees, continues with an abstraction of the relevant features, and ends with the transfer of a design methodology for long reinforced and prestressed concrete columns. To verify the applicability and validity of the mathematical relationships extracted from the bibliographic study to characterize the biomechanics of coniferous trees, a study site is conducted for Norway spruce trees felled by the wind in the Bilbor area. The design methodology for long reinforced and prestressed concrete columns bioinspired by the Norway spruce trees is experimentally validated using two case studies. The first case study deals with the effect of centric prestressing on long concrete columns, and the second on the influence of the walnut shell powder on the adhesion of the reinforcement in concrete. The case studies presented aim to transfer some characteristics from trees to reinforced concrete to improve the performance of long columns under horizontal forces. The results obtained indicate a good approximation of the trees’ structural behavior for this site and for ones investigated by other researchers in different forests.
- Open Access
Assessment of Limestone Waste Addition for Fired Clay Bricks
Our aim was to investigate the feasibility of using limestone waste resulting from stone processing for the manufacturing of fired clay bricks. Waste materials were considered as a partial replacement for clays to reduce the exploitation of natural resources and as a response to the climate neutrality commitments. The samples were prepared to have a waste content of up to 15% and were fired at a temperature of 900 °C. The chemical and mineralogical composition and the physical analysis of raw materials were investigated by using SEM–EDS and XRD diffraction. The result showed an increase in CaO in the clay mixture due to the presence of limestone, which reduced the shrinkage of the products’ compressive strength, up to 55% for samples with a higher content of limestone (15 wt.%), and influenced the samples’ color by making them lighter than the reference sample.
Open AccessAssessment of Limestone Waste Addition for Fired Clay Bricks
Our aim was to investigate the feasibility of using limestone waste resulting from stone processing for the manufacturing of fired clay bricks. Waste materials were considered as a partial replacement for clays to reduce the exploitation of natural resources and as a response to the climate neutrality commitments. The samples were prepared to have a waste content of up to 15% and were fired at a temperature of 900 °C. The chemical and mineralogical composition and the physical analysis of raw materials were investigated by using SEM–EDS and XRD diffraction. The result showed an increase in CaO in the clay mixture due to the presence of limestone, which reduced the shrinkage of the products’ compressive strength, up to 55% for samples with a higher content of limestone (15 wt.%), and influenced the samples’ color by making them lighter than the reference sample.
- Open Access
Volcanic Tuff as Secondary Raw Material in the Production of Clay Bricks
The present work examines an innovative manufacturing technique for fired clay bricks, using tuff as a secondary raw material. Samples were made of clay and tuff (0–30 wt.%) fired at 900 to 1100 °C. The chemical and mineralogical compositions and physical and thermal analyses of raw materials were investigated by using SEM-EDS, RX and DTA-TG curves. The samples were analysed from the mineralogical, technological and mechanical points of view. The result show that the tuff’s presence in the clay mixtures considerably reduced the shrinkage of the product during the firing process, and the manufactured samples were of excellent quality. The compressive strength of the bricks varied from 5–35.3MPa, being influenced by the tuff content, clay matrix properties and firing temperatures. Finally, the heat demand for increasing the temperature from room to the firing temperature of the sample with 10% tuff content was 22%.
Open AccessVolcanic Tuff as Secondary Raw Material in the Production of Clay Bricks
The present work examines an innovative manufacturing technique for fired clay bricks, using tuff as a secondary raw material. Samples were made of clay and tuff (0–30 wt.%) fired at 900 to 1100 °C. The chemical and mineralogical compositions and physical and thermal analyses of raw materials were investigated by using SEM-EDS, RX and DTA-TG curves. The samples were analysed from the mineralogical, technological and mechanical points of view. The result show that the tuff’s presence in the clay mixtures considerably reduced the shrinkage of the product during the firing process, and the manufactured samples were of excellent quality. The compressive strength of the bricks varied from 5–35.3MPa, being influenced by the tuff content, clay matrix properties and firing temperatures. Finally, the heat demand for increasing the temperature from room to the firing temperature of the sample with 10% tuff content was 22%.
- Open Access
Development of New Composite Products Based on Flax Fibres
Plant fibres are materials that can increase energy savings, and they are being analysed for their reduced environmental impact. In this paper, three types of multi-layered panels were developed as environmentally friendly flax fibre-based products for building industry applications. The structural build-up of the panels is such that one layer of waste flax fibre was used as the core material in order to reduce the weight of the structure between two rigid perlite-based layers. The perlite was used in three varied grain sizes, resulting in three types of panels (S1, S2, S3). The mechanical, thermal and acoustic properties were recorded for all specimens. The influence of the perlite particles’ size, perforation diameter and perforation percentage of the multi-layered panels on the acoustic absorption properties was analysed and discussed. Summarising the results, the multi-layered composite panel S3 presented the best performance in regard to compressive strength and thermal conductivity, with S2 presenting the best bending strength. From the acoustic point of view, for the unperforated panels, the highest values of the sound absorption coefficient were obtained at 500 Hz for S1, α = 0.95, 315 Hz for S2, α = 0.89 and 400 Hz for S3, α = 0.84. The obtained values of the sound absorption coefficients were increased through the varied perforation diameters and percentages of the panels’ front face.
Open AccessDevelopment of New Composite Products Based on Flax Fibres
Plant fibres are materials that can increase energy savings, and they are being analysed for their reduced environmental impact. In this paper, three types of multi-layered panels were developed as environmentally friendly flax fibre-based products for building industry applications. The structural build-up of the panels is such that one layer of waste flax fibre was used as the core material in order to reduce the weight of the structure between two rigid perlite-based layers. The perlite was used in three varied grain sizes, resulting in three types of panels (S1, S2, S3). The mechanical, thermal and acoustic properties were recorded for all specimens. The influence of the perlite particles’ size, perforation diameter and perforation percentage of the multi-layered panels on the acoustic absorption properties was analysed and discussed. Summarising the results, the multi-layered composite panel S3 presented the best performance in regard to compressive strength and thermal conductivity, with S2 presenting the best bending strength. From the acoustic point of view, for the unperforated panels, the highest values of the sound absorption coefficient were obtained at 500 Hz for S1, α = 0.95, 315 Hz for S2, α = 0.89 and 400 Hz for S3, α = 0.84. The obtained values of the sound absorption coefficients were increased through the varied perforation diameters and percentages of the panels’ front face.
- Open Access
- 30 June 2020
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 70 (338) , e215
Influence of sawdust particle size on fired clay brick properties
This study investigates the effect of adding different size fractions of the same pore forming agent (sawdust) on the material’s compressive strength and heat transfer. The samples were dry pressed and fired at high temperature inside an oven. Phase transformations were evidenced by a combination of differential thermal analysis, thermogravimetry and mass spectrometry (DTA-TGA-MS) and X-ray diffraction (XRD) techniques, in the temperature range of 24-900 ºC. Image analysis (IA) and compression tests were performed to explain the mechanical behaviour of the samples. The thermal conductivity was obtained by using combined photopyroelectric calorimetry (PPE) and lock-in thermography (LIT) techniques. The pressing direction has an impact on the distribution of pores and the heat transfer by conduction.
- 30 June 2020
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 70 (338) , e215
Open AccessInfluence of sawdust particle size on fired clay brick properties
This study investigates the effect of adding different size fractions of the same pore forming agent (sawdust) on the material’s compressive strength and heat transfer. The samples were dry pressed and fired at high temperature inside an oven. Phase transformations were evidenced by a combination of differential thermal analysis, thermogravimetry and mass spectrometry (DTA-TGA-MS) and X-ray diffraction (XRD) techniques, in the temperature range of 24-900 ºC. Image analysis (IA) and compression tests were performed to explain the mechanical behaviour of the samples. The thermal conductivity was obtained by using combined photopyroelectric calorimetry (PPE) and lock-in thermography (LIT) techniques. The pressing direction has an impact on the distribution of pores and the heat transfer by conduction.
- 1 January 2020
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 64 (4) , 1153-1161
An Investigation on Sheeting Acting as a Diaphragm on a Reinforced Precast Concrete Frame
It is well-known that for single-storey steel structures, the framework is greatly strengthened and stiffened following the attachment of the roof, floors and walls. The panels in the roofing, flooring and side cladding are also known as "shear diaphragms" by virtue of their resistance to being deformed into parallelograms. This has been verified by on-site practical experience of many structures and design provisions are available for structural engineers. Despite the fact that for single-storey structures, the corrugated steel sheets are the standard elements in constructing the envelopes, in what concerns the reinforced concrete frames there are no guidelines nor recommendations on how to consider the diaphragm effect in structural analysis. In order to better understand the interaction between the corrugated steel sheets and the reinforced concrete frame, a real precast reinforced concrete frame structure was built for experimental testing. The aim of the experimental test is to study the diaphragm effect for reinforced concrete structures and based on the results to identify the discrepancies identified compared to steel structures. The investigation attempts to provide a starting point for future research on the stressed skin design acting on reinforced concrete frames. At the end of the article conclusions are drawn based on the experience obtained during the experimental test.
- 1 January 2020
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 64 (4) , 1153-1161
An Investigation on Sheeting Acting as a Diaphragm on a Reinforced Precast Concrete Frame
It is well-known that for single-storey steel structures, the framework is greatly strengthened and stiffened following the attachment of the roof, floors and walls. The panels in the roofing, flooring and side cladding are also known as "shear diaphragms" by virtue of their resistance to being deformed into parallelograms. This has been verified by on-site practical experience of many structures and design provisions are available for structural engineers. Despite the fact that for single-storey structures, the corrugated steel sheets are the standard elements in constructing the envelopes, in what concerns the reinforced concrete frames there are no guidelines nor recommendations on how to consider the diaphragm effect in structural analysis. In order to better understand the interaction between the corrugated steel sheets and the reinforced concrete frame, a real precast reinforced concrete frame structure was built for experimental testing. The aim of the experimental test is to study the diaphragm effect for reinforced concrete structures and based on the results to identify the discrepancies identified compared to steel structures. The investigation attempts to provide a starting point for future research on the stressed skin design acting on reinforced concrete frames. At the end of the article conclusions are drawn based on the experience obtained during the experimental test.
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia Manufacturing
- Vol. 32, 242-247
Psyllium Seeds Used as Pore Forming Agent in Clay Bricks
- 1 January 2019
- Published by Elsevier in Procedia Manufacturing
- Vol. 32, 242-247
Open AccessPsyllium Seeds Used as Pore Forming Agent in Clay Bricks
- 19 March 2018
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 134 (1) , 843-851
Thermophysical properties of fired clay bricks with waste ceramics and paper pulp as pore-forming agent
- 19 March 2018
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 134 (1) , 843-851
Thermophysical properties of fired clay bricks with waste ceramics and paper pulp as pore-forming agent