Christina Schindler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Christina Schindler has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Rainer Waser
Peter-Grnberg-Institut 7 (PGI-7), Forschungszentrum Jlich GmbH, Jlich, Germany
12 shared publications - Martin Weides
James Watt School of Engineering, University of Glasgow 1 , Glasgow G12 8QQ
4 shared publications - Andreas Ruediger
Énergie Matériaux Télécommunications Research Centre Institut National De La Recherche Scientifique Varennes Quebec Canada
3 shared publications Michael Kaiser
Department of Applied Sciences and Mechatronics University of Applied Sciences Munich Lothstraße 34 Munich 80335 Germany
3 shared publicationsA. Ruediger
2 shared publicationsAndreas Ruediger
Nanoelectronics - Nanophotonics, INRS-EMT, Varennes, Canada
2 shared publications
Latest Publications
- 1 September 2021
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 6 (3) , 035011
Sinter-free inkjet-printed PEDOT:PSS/WO 3 /PEDOT:PSS flexible valency change memory
With the rapid proliferation of consumer electronics in our day to day lives, there is an ever increasing demand for flexible electronic devices which are low cost, easy to fabricate and deliver reliable performance. In this work, we report fabrication of symmetric poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS)/WO 3 /PEDOT:PSS memory cells by inkjet printing on transparent, flexible polyethylene naphthalate (PEN) substrates. The cells show resistive switching behavior with two stable resistance states. The current conduction across the interface between the PEDOT:PSS electrode and dielectric WO 3 is determined by localized filamentary features which is space charge limited in the high resistance state, facilitated through the migration of oxygen vacancies at low voltages (2 V). The cells show good retentivity and endurance (>6000 cycles). The cells are entirely sinter free and no electroforming is required to activate them. These characteristics make them suitable for the next generation of flexible non-volatile memory devices.
- 1 September 2021
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 6 (3) , 035011
Sinter-free inkjet-printed PEDOT:PSS/WO 3 /PEDOT:PSS flexible valency change memory
With the rapid proliferation of consumer electronics in our day to day lives, there is an ever increasing demand for flexible electronic devices which are low cost, easy to fabricate and deliver reliable performance. In this work, we report fabrication of symmetric poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS)/WO 3 /PEDOT:PSS memory cells by inkjet printing on transparent, flexible polyethylene naphthalate (PEN) substrates. The cells show resistive switching behavior with two stable resistance states. The current conduction across the interface between the PEDOT:PSS electrode and dielectric WO 3 is determined by localized filamentary features which is space charge limited in the high resistance state, facilitated through the migration of oxygen vacancies at low voltages (2 V). The cells show good retentivity and endurance (>6000 cycles). The cells are entirely sinter free and no electroforming is required to activate them. These characteristics make them suitable for the next generation of flexible non-volatile memory devices.
- Open Access
- 16 November 2020
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 306 (2)
Fiber‐Optic Photoacoustic Generator Realized by Inkjet‐Printing of CNT‐PDMS Composites on Fiber End Faces
In recent years, photoacoustic generators based on multiwalled carbon nanotubes (MWCNT) and polydimethylsiloxane (PDMS) are manufactured in a variety of ways, which influences the properties of the generators with respect to frequency bandwidth, sound wave pressure, robustness, and reproducibility. Due to the high optical absorption of MWCNTs and the high thermal expansion coefficient of PDMS, this combination is ideally suited for use as a photoacoustic generator. This study presents a novel method to produce photoacoustic generators based on long‐term stable MWCNT and PDMS inks with a high reproducibility by means of inkjet‐printing. The MWCNT‐PDMS layers (thicknesses of 2–4 µm), printed directly onto the distal end face of a multimode glass fiber, show a good homogeneity and low optical transmission (19–21%). After the preparation of the fiber pieces, the inkjet printer performs all steps automatically in a time period of 30–60 s per layer. The generated ultrasonic pressure (0.39–0.54 MPa) and frequency bandwidth (1.5–12.7 MHz) can be measured at a distance of ≈4 mm with a laser fluency of 12.7 mJ cm−2. These highly reproducible printed photoacoustic generators can be well used for nondestructive material testing and medical applications.
- 16 November 2020
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 306 (2)
Open AccessFiber‐Optic Photoacoustic Generator Realized by Inkjet‐Printing of CNT‐PDMS Composites on Fiber End Faces
In recent years, photoacoustic generators based on multiwalled carbon nanotubes (MWCNT) and polydimethylsiloxane (PDMS) are manufactured in a variety of ways, which influences the properties of the generators with respect to frequency bandwidth, sound wave pressure, robustness, and reproducibility. Due to the high optical absorption of MWCNTs and the high thermal expansion coefficient of PDMS, this combination is ideally suited for use as a photoacoustic generator. This study presents a novel method to produce photoacoustic generators based on long‐term stable MWCNT and PDMS inks with a high reproducibility by means of inkjet‐printing. The MWCNT‐PDMS layers (thicknesses of 2–4 µm), printed directly onto the distal end face of a multimode glass fiber, show a good homogeneity and low optical transmission (19–21%). After the preparation of the fiber pieces, the inkjet printer performs all steps automatically in a time period of 30–60 s per layer. The generated ultrasonic pressure (0.39–0.54 MPa) and frequency bandwidth (1.5–12.7 MHz) can be measured at a distance of ≈4 mm with a laser fluency of 12.7 mJ cm−2. These highly reproducible printed photoacoustic generators can be well used for nondestructive material testing and medical applications.
- Open Access
- 4 July 2019
- Published by Wiley in Advanced Intelligent Systems
- Vol. 1 (5)
CMOS Compatible Hf0.5Zr0.5O2 Ferroelectric Tunnel Junctions for Neuromorphic Devices
While machine learning algorithms are becoming more and more elaborate, their underlying artificial neural networks most often still rely on the binary von Neumann computer architecture. However, artificial neural networks access their full potential when combined with gradually switchable artificial synapses. Herein, complementary metal oxide semiconductor‐compatible Hf0.5Zr0.5O2 ferroelectric tunnel junctions fabricated by radio‐frequency magnetron sputtering are used as artificial synapses. On a single synapse level, their neuromorphic behavior is quantitatively investigated with spike‐timing‐dependent plasticity. It is found that the learning rate of the synapses mainly depends on the voltage amplitude of the applied stimulus. The experimental findings are well reproduced with simulations based on the nucleation‐limited‐switching model.
- 4 July 2019
- Published by Wiley in Advanced Intelligent Systems
- Vol. 1 (5)
Open AccessCMOS Compatible Hf0.5Zr0.5O2 Ferroelectric Tunnel Junctions for Neuromorphic Devices
While machine learning algorithms are becoming more and more elaborate, their underlying artificial neural networks most often still rely on the binary von Neumann computer architecture. However, artificial neural networks access their full potential when combined with gradually switchable artificial synapses. Herein, complementary metal oxide semiconductor‐compatible Hf0.5Zr0.5O2 ferroelectric tunnel junctions fabricated by radio‐frequency magnetron sputtering are used as artificial synapses. On a single synapse level, their neuromorphic behavior is quantitatively investigated with spike‐timing‐dependent plasticity. It is found that the learning rate of the synapses mainly depends on the voltage amplitude of the applied stimulus. The experimental findings are well reproduced with simulations based on the nucleation‐limited‐switching model.
- Open Access
- 1 June 2019
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 10 (6) , 405-409
Oxygen vacancy filament-based resistive switching in Hf0.5Zr0.5O2 thin films for non-volatile memory
The continued evolution of electronic devices relies on the development of new semiconductor memory technology. Given the high compatibility of the Hf0.5Zr0.5O2 thin films with the CMOS technology, we investigate the charge transport mechanisms that occur in a relative thick Hf0.5Zr0.5O2 thin film (4 to 6 nm-thick) when subjected to electrical stresses. To that end we fabricate Hf0.5Zr0.5O2 heterostructures with a Pt tip as the top electrode and TiN and Pt as bottom electrode by radio-frequency magnetron sputtering. After analyzing the surface morphology of the as-received and as-deposited films by atomic force microscopy, the transfer of the desired chemical stoichiometry from the sputtering target to the substrate surface is studied by Raman spectroscopy. The ferroelectricity of the Hf0.5Zr0.5O2 thin films is confirmed by piezoresponse force microscopy measurements, and a retention of 22 h is obtained, attesting to the non-volatility of the samples. Nano-scale electrical measurements reveal the presence of resistive switching, where the low resistance state (ON state) in both Pt-tip/Hf0.5Zr0.5O2/TiN and Pt-tip/Hf0.5Zr0.5O2/Pt heterostructures can be created by the formation of a conductive filament based on oxygen vacancies.
- 1 June 2019
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 10 (6) , 405-409
Open AccessOxygen vacancy filament-based resistive switching in Hf0.5Zr0.5O2 thin films for non-volatile memory
The continued evolution of electronic devices relies on the development of new semiconductor memory technology. Given the high compatibility of the Hf0.5Zr0.5O2 thin films with the CMOS technology, we investigate the charge transport mechanisms that occur in a relative thick Hf0.5Zr0.5O2 thin film (4 to 6 nm-thick) when subjected to electrical stresses. To that end we fabricate Hf0.5Zr0.5O2 heterostructures with a Pt tip as the top electrode and TiN and Pt as bottom electrode by radio-frequency magnetron sputtering. After analyzing the surface morphology of the as-received and as-deposited films by atomic force microscopy, the transfer of the desired chemical stoichiometry from the sputtering target to the substrate surface is studied by Raman spectroscopy. The ferroelectricity of the Hf0.5Zr0.5O2 thin films is confirmed by piezoresponse force microscopy measurements, and a retention of 22 h is obtained, attesting to the non-volatility of the samples. Nano-scale electrical measurements reveal the presence of resistive switching, where the low resistance state (ON state) in both Pt-tip/Hf0.5Zr0.5O2/TiN and Pt-tip/Hf0.5Zr0.5O2/Pt heterostructures can be created by the formation of a conductive filament based on oxygen vacancies.
- 18 January 2019
- Published by Taylor & Francis in Materials Technology
- Vol. 34 (6) , 350-355
Comparison of spin-on-glass and WO3 as an insulating layer for printed resistive memory devices
Resistive Random Access Memory (ReRAM) is a highly promising technology for various future memory applications. In this work, spin-on-glass (SOG) and WO3 nanoparticles are used as an insulating layer for completely inkjet-printed ReRAM cells. The direct comparison shows that the difference in switching parameters can be used to serve different device requirements for various applications. While local filament formation with conductive atomic force microscopy confirms the same switching mechanism for both compounds, the current–voltage characteristics differ from each other. SOG as excellent insulator shows an OFF resistance in the range of GΩ and is therefore highly suitable for multi-bit data storage to increase memory density. ReRAM cells with WO3 face larger leakage currents and show a low degree of multi-bit data storage. However, WO3 can be used to fabricate completely sinter-free memory devices for applications which do not allow high temperatures in the fabrication process.
- 18 January 2019
- Published by Taylor & Francis in Materials Technology
- Vol. 34 (6) , 350-355
Comparison of spin-on-glass and WO3 as an insulating layer for printed resistive memory devices
Resistive Random Access Memory (ReRAM) is a highly promising technology for various future memory applications. In this work, spin-on-glass (SOG) and WO3 nanoparticles are used as an insulating layer for completely inkjet-printed ReRAM cells. The direct comparison shows that the difference in switching parameters can be used to serve different device requirements for various applications. While local filament formation with conductive atomic force microscopy confirms the same switching mechanism for both compounds, the current–voltage characteristics differ from each other. SOG as excellent insulator shows an OFF resistance in the range of GΩ and is therefore highly suitable for multi-bit data storage to increase memory density. ReRAM cells with WO3 face larger leakage currents and show a low degree of multi-bit data storage. However, WO3 can be used to fabricate completely sinter-free memory devices for applications which do not allow high temperatures in the fabrication process.
- 21 August 2018
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 3 (3) , 035005
Rotate-to-bend setup for fatigue bending tests on inkjet-printed silver lines
For the growing field of flexible electronics the performance of fabricated flexible devices during bending deformation has to be investigated in order to guarantee their resilience against small bending radii and bending fatigue. We report on a rotate-to-bend apparatus, which allows for arbitrary sequences of compressive as well as tensile bending and a wide range of selectable bending radii without applying additional strain. The electrical characterization can be conducted simultaneously with high speed measurement. We test the rotate-to-bend device on inkjet-printed conducting paths of Ag nanoparticles and Ag nanowires on various foil substrates. Fatigue bending cycles show that tensile deformation leads to a higher increase in resistance of the printed lines compared to compressive strain. This is caused by the higher tendency of microcracks to form during tensile bending. We also show the high negative impact of the substrate thickness on bending fatigue during full bending cycles. Here, Ag nanowires show superior fatigue behaviour compared to the nanoparticle lines due to their flexible, mesh-like network. The rotate-to-bend apparatus could become an efficient and inexpensive device for the testing of flexible devices.
- 21 August 2018
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 3 (3) , 035005
Rotate-to-bend setup for fatigue bending tests on inkjet-printed silver lines
For the growing field of flexible electronics the performance of fabricated flexible devices during bending deformation has to be investigated in order to guarantee their resilience against small bending radii and bending fatigue. We report on a rotate-to-bend apparatus, which allows for arbitrary sequences of compressive as well as tensile bending and a wide range of selectable bending radii without applying additional strain. The electrical characterization can be conducted simultaneously with high speed measurement. We test the rotate-to-bend device on inkjet-printed conducting paths of Ag nanoparticles and Ag nanowires on various foil substrates. Fatigue bending cycles show that tensile deformation leads to a higher increase in resistance of the printed lines compared to compressive strain. This is caused by the higher tendency of microcracks to form during tensile bending. We also show the high negative impact of the substrate thickness on bending fatigue during full bending cycles. Here, Ag nanowires show superior fatigue behaviour compared to the nanoparticle lines due to their flexible, mesh-like network. The rotate-to-bend apparatus could become an efficient and inexpensive device for the testing of flexible devices.
- 1 July 2018
- Published by Elsevier in Microelectronic Engineering
- Vol. 194, 85-88
Inkjet-printed resistive memory cells for transparent electronics
- 1 July 2018
- Published by Elsevier in Microelectronic Engineering
- Vol. 194, 85-88
Inkjet-printed resistive memory cells for transparent electronics
- 3 April 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (14) , 143503
Fully inkjet printed flexible resistive memory
Resistively switching memory cells (ReRAM) are strong contenders for next-generation non-volatile random access memories. In this paper, we present ReRAM cells on flexible substrates consisting of Ag/spin-on-glass/PEDOT:PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate). The complete cell is fabricated using a standard inkjet printer without additional process steps. Investigations on the spin-on-glass insulating layer showed that low sintering temperatures are sufficient for good switching behavior, providing compatibility with various foils. The cells feature low switching voltages, low write currents, and a high ratio between high and low resistance state of 104. Combined with excellent switching characteristics under bending conditions, these results pave the way for low-power and low-cost memory devices for future applications in flexible electronics.
- 3 April 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (14) , 143503
Fully inkjet printed flexible resistive memory
Resistively switching memory cells (ReRAM) are strong contenders for next-generation non-volatile random access memories. In this paper, we present ReRAM cells on flexible substrates consisting of Ag/spin-on-glass/PEDOT:PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate). The complete cell is fabricated using a standard inkjet printer without additional process steps. Investigations on the spin-on-glass insulating layer showed that low sintering temperatures are sufficient for good switching behavior, providing compatibility with various foils. The cells feature low switching voltages, low write currents, and a high ratio between high and low resistance state of 104. Combined with excellent switching characteristics under bending conditions, these results pave the way for low-power and low-cost memory devices for future applications in flexible electronics.
- 21 January 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (5) , 1353-1357
Partially printed resistive memory cells on rigid and flexible substrates
- 21 January 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (5) , 1353-1357
Partially printed resistive memory cells on rigid and flexible substrates
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A novel planar level chip interconnection for unpackaged MMICs in the millimeter wave frequency range
This paper presents a novel planar interconnection technology for unpackaged monolithic microwave integrated circuits (MMICs), which work in the millimeter wave (mmw) frequency range. Compared to standard wire bonding, the new technique provides considerable advantages with regard to the electrical characteristics and manufacturing processes. The manufacturing process for a module containing surface mounted devices (SMD) and unpackaged MMICs is described. In order to determine the electrical behavior, a model of a single interconnection is developed using a full wave field simulation and compared to a model of a wire bond. Finally, the insertion losses are determined by measuring the output power of an active frequency doubler, which is assembled using both technologies. Because of the availability of commercial MMICs an operating frequency of 77 GHz is considered.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A novel planar level chip interconnection for unpackaged MMICs in the millimeter wave frequency range
This paper presents a novel planar interconnection technology for unpackaged monolithic microwave integrated circuits (MMICs), which work in the millimeter wave (mmw) frequency range. Compared to standard wire bonding, the new technique provides considerable advantages with regard to the electrical characteristics and manufacturing processes. The manufacturing process for a module containing surface mounted devices (SMD) and unpackaged MMICs is described. In order to determine the electrical behavior, a model of a single interconnection is developed using a full wave field simulation and compared to a model of a wire bond. Finally, the insertion losses are determined by measuring the output power of an active frequency doubler, which is assembled using both technologies. Because of the availability of commercial MMICs an operating frequency of 77 GHz is considered.