Sandip V. Kamat
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sandip V. Kamat has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Vijaya Puri
Thick and Thin Film laboratory, Department of Phhysics, Shivaji University, Kolhapur, M.S. India, 416004
9 shared publicationsR.K. Puri
5 shared publicationsR. K. Puri
Vacuum Techniques and thin film Laboratory, USIC, Shivaji University, Kolhapur, M.S. India, 416004
3 shared publicationsJ.B. Yadav
2 shared publications- Sikandar H. Tamboli
Department of Mechanical Engineering, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-749, Korea
2 shared publications - Vaishali S. Patil
Vacuum Techniques and thin film Laboratory, USIC, Shivaji University, Kolhapur, M.S. India, 416004
2 shared publications
Latest Publications
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1953 (1) , 030061
Consequence of oxidant concentration on XPS properties of chemically synthesized polythiophene thin films
The polythiophene thin films were prepared by a wellknown chemical bath deposition technique. The deposited thin films were characterized for structural morphological properties and the adhesion of these thin films were measured by direct pull off (DPO) method, the effect of oxidant concentration on these thin films also studied. The FTIR spectra of chemically deposited polythiophene thin films shows the absorption peak at 836 cm−1 which represents c–s stretching vibrations, shifts to 869 cm−1 as the oxidant concentration increases. The band at 666 cm−1 representing c–s–c ring deformation becomes sharper and appears with a shoulder peak due to increase in oxidant concentration.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1953 (1) , 030061
Consequence of oxidant concentration on XPS properties of chemically synthesized polythiophene thin films
The polythiophene thin films were prepared by a wellknown chemical bath deposition technique. The deposited thin films were characterized for structural morphological properties and the adhesion of these thin films were measured by direct pull off (DPO) method, the effect of oxidant concentration on these thin films also studied. The FTIR spectra of chemically deposited polythiophene thin films shows the absorption peak at 836 cm−1 which represents c–s stretching vibrations, shifts to 869 cm−1 as the oxidant concentration increases. The band at 666 cm−1 representing c–s–c ring deformation becomes sharper and appears with a shoulder peak due to increase in oxidant concentration.
- 1 July 2012
- Published by Elsevier in Applied Surface Science
- Vol. 258 (19) , 7567-7573
Modification of the properties of polythiophene thin films by vapor chopping
- 1 July 2012
- Published by Elsevier in Applied Surface Science
- Vol. 258 (19) , 7567-7573
Modification of the properties of polythiophene thin films by vapor chopping
- Open Access
- 21 March 2012
- Published by Hindawi Limited in ISRN Polymer Science
- Vol. 2012, 1-8
The Effect of Film Thickness on the Structural Properties of Vacuum Evaporated Poly(3-methylthiophene) Thin Films
This paper reports on the structural properties of poly(3-methylthiophene) P3MeT thin films prepared by vacuum evaporation on the glass substrates. The structural and surface morphology, wettability, adhesion, and intrinsic stress of these thin films were studied for three different thicknesses. The variation of the film thickness affects the structure, surface, and mechanical properties of P3MeT thin films. Vapor chopping also strongly influences the surface morphology, surface roughness, and wettability of the thin films. It was found that there is a decrease in the intrinsic stress and (RMS) roughness, while the adhesion increases with increase in film thickness.
- 21 March 2012
- Published by Hindawi Limited in ISRN Polymer Science
- Vol. 2012, 1-8
Open AccessThe Effect of Film Thickness on the Structural Properties of Vacuum Evaporated Poly(3-methylthiophene) Thin Films
This paper reports on the structural properties of poly(3-methylthiophene) P3MeT thin films prepared by vacuum evaporation on the glass substrates. The structural and surface morphology, wettability, adhesion, and intrinsic stress of these thin films were studied for three different thicknesses. The variation of the film thickness affects the structure, surface, and mechanical properties of P3MeT thin films. Vapor chopping also strongly influences the surface morphology, surface roughness, and wettability of the thin films. It was found that there is a decrease in the intrinsic stress and (RMS) roughness, while the adhesion increases with increase in film thickness.
- 1 January 2012
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 132 (1) , 228-232
Room temperature synthesis and characterization of polythiophene thin films by chemical bath deposition (CBD) method
- 1 January 2012
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 132 (1) , 228-232
Room temperature synthesis and characterization of polythiophene thin films by chemical bath deposition (CBD) method
- 1 October 2011
- Published by Elsevier in Applied Surface Science
- Vol. 258 (1) , 482-488
Characterization of poly (3-methyl thiophene) thin films prepared by modified chemical bath deposition
- 1 October 2011
- Published by Elsevier in Applied Surface Science
- Vol. 258 (1) , 482-488
Characterization of poly (3-methyl thiophene) thin films prepared by modified chemical bath deposition
- 13 September 2011
- Published by IOP Publishing in Physica Scripta
- Vol. 84 (4)
Determination of the optical constants of a vacuum evaporated polythiophene thin film
- 13 September 2011
- Published by IOP Publishing in Physica Scripta
- Vol. 84 (4)
Determination of the optical constants of a vacuum evaporated polythiophene thin film
- Open Access
- 1 January 2011
- Published by The Electromagnetics Academy in Progress In Electromagnetics Research M
- Vol. 18, 197-207
DETERMINATION OF OPTICAL TRANSMISSION LOSS IN POLY (3-METHYL THIOPHENE) THIN FILM PLANAR WAVEGUIDE: EFFECT OF VAPOUR CHOPPING
This article reports the effect of vapour chopping technique on the properties of vacuum evaporated poly (3methyl thiophene) thin films such as surface morphology, optical transmittance, band gap, refractive index and optical transmission loss. Vapour chopping gives smooth surface morphology with smaller grain size reduced roughness than non chopped thin films, while the transmittance of the thin film increases with simultaneous decrease in the refractive index, band gap and optical transmission loss decreases due to vapour chopping.
- 1 January 2011
- Published by The Electromagnetics Academy in Progress In Electromagnetics Research M
- Vol. 18, 197-207
Open AccessDETERMINATION OF OPTICAL TRANSMISSION LOSS IN POLY (3-METHYL THIOPHENE) THIN FILM PLANAR WAVEGUIDE: EFFECT OF VAPOUR CHOPPING
This article reports the effect of vapour chopping technique on the properties of vacuum evaporated poly (3methyl thiophene) thin films such as surface morphology, optical transmittance, band gap, refractive index and optical transmission loss. Vapour chopping gives smooth surface morphology with smaller grain size reduced roughness than non chopped thin films, while the transmittance of the thin film increases with simultaneous decrease in the refractive index, band gap and optical transmission loss decreases due to vapour chopping.
- 1 May 2009
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 477 (1-2) , 855-859
Modification of optical properties of MgO thin films by vapour chopping
- 1 May 2009
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 477 (1-2) , 855-859
Modification of optical properties of MgO thin films by vapour chopping