Dirk-Holger Neuhaus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dirk-Holger Neuhaus has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Matthias Müller
Institute of Applied Physics TU Bergakademie Freiberg Freiberg Germany
4 shared publications A.G. Aberle
2 shared publicationsArmin G. Aberle
Photovoltaics Special Research Centre, University of New South Wales, Sydney NSW 2052, Australia
2 shared publicationsEric Schneiderlöchner
2 shared publicationsGerd Fischer
2 shared publications- Julian Weber
Fraunhofer Institute for Solar Energy Systems ISE Freiburg Germany
2 shared publications
Latest Publications
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Analysis of Thermal Behavior and Reliability of Bare Die Diodes Embedded Within PV Modules as Bypass Devices
The installation of bypass devices embedded within a photovoltaic (PV) module is an increasingly attractive option for simplifying module design and manufacturing, offering an alternative to the current standard of connecting and gluing to the laminated module one or more external boxes containing the bypass diodes. However, certain technical challenges require further exploration for a reliable integration. We analyze the role of the geometry of the diode, and of the module's bill of materials (BOM) in dissipating heat when partial shading occurs on a PV array, putting the diode in forward bias. Critical parameters for module-integrated bare die diodes are defined such that its maximum operating temperature remains below 95 °C. Different approaches are explored experimentally and a Finite Element Method (FEM) model is created to predict said maximum temperatures. It is found that while the chip size is one main factor in dissipating heat efficiently, other methods for modifying the geometry of the diode-connectors subassembly can aid considerably in reducing the temperature of the device during operation, all without substantially increasing the size of the semiconductor. Connecting in parallel two or more small diodes, increasing the width of the connectors, and adding flat heat sinks are some of the proposed approaches. Furthermore, performance and reliability tests are executed to understand how degradation of the integrated diodes might affect the lifetime of the PV module, showing that when operation temperatures above 130°C are maintained even for a relatively short time, some degradation of the electrical contacting of the diode will occur.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Analysis of Thermal Behavior and Reliability of Bare Die Diodes Embedded Within PV Modules as Bypass Devices
The installation of bypass devices embedded within a photovoltaic (PV) module is an increasingly attractive option for simplifying module design and manufacturing, offering an alternative to the current standard of connecting and gluing to the laminated module one or more external boxes containing the bypass diodes. However, certain technical challenges require further exploration for a reliable integration. We analyze the role of the geometry of the diode, and of the module's bill of materials (BOM) in dissipating heat when partial shading occurs on a PV array, putting the diode in forward bias. Critical parameters for module-integrated bare die diodes are defined such that its maximum operating temperature remains below 95 °C. Different approaches are explored experimentally and a Finite Element Method (FEM) model is created to predict said maximum temperatures. It is found that while the chip size is one main factor in dissipating heat efficiently, other methods for modifying the geometry of the diode-connectors subassembly can aid considerably in reducing the temperature of the device during operation, all without substantially increasing the size of the semiconductor. Connecting in parallel two or more small diodes, increasing the width of the connectors, and adding flat heat sinks are some of the proposed approaches. Furthermore, performance and reliability tests are executed to understand how degradation of the integrated diodes might affect the lifetime of the PV module, showing that when operation temperatures above 130°C are maintained even for a relatively short time, some degradation of the electrical contacting of the diode will occur.
- 10 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999 (1) , 110005
Development and characterization of multifunctional PECVD SiNX:P layers for laser-doped selective emitters
We apply stacks of silicon nitride (SiNX) layers consisting of phosphorus-doped SiNX (SiNX:P) and undoped SiNX as first and second layer, on the front surface of p-type monocrystalline silicon passivated emitter and rear cells (PERC). The stack is deposited using plasma-enhanced chemical vapor deposition. These layer stacks provide excellent surface passivation and anti-reflection properties comparable to single undoped SiNX layers. A laser processing locally introduces the phosphorus dopants from the SiNX:P/SiNX layer stack into the silicon and locally removes the layer stack. Thereby, local highly doped areas with sheet resistances as low as Rsh ≈ 20 Ω/sq are obtained. We refer to this as the nPassDop approach, which provides local high doping and structuring of the anti-reflection coating in one process. The saturation current density of the laser processed areas is estimated to be as low as j0,laser ≈ 500 fA/cm2. First implementations for large-area p-type Cz-Si PERC cells with self-aligned NiCuAg plated front contacts yield an energy conversion efficiency of 19.6%.
- 10 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999 (1) , 110005
Development and characterization of multifunctional PECVD SiNX:P layers for laser-doped selective emitters
We apply stacks of silicon nitride (SiNX) layers consisting of phosphorus-doped SiNX (SiNX:P) and undoped SiNX as first and second layer, on the front surface of p-type monocrystalline silicon passivated emitter and rear cells (PERC). The stack is deposited using plasma-enhanced chemical vapor deposition. These layer stacks provide excellent surface passivation and anti-reflection properties comparable to single undoped SiNX layers. A laser processing locally introduces the phosphorus dopants from the SiNX:P/SiNX layer stack into the silicon and locally removes the layer stack. Thereby, local highly doped areas with sheet resistances as low as Rsh ≈ 20 Ω/sq are obtained. We refer to this as the nPassDop approach, which provides local high doping and structuring of the anti-reflection coating in one process. The saturation current density of the laser processed areas is estimated to be as low as j0,laser ≈ 500 fA/cm2. First implementations for large-area p-type Cz-Si PERC cells with self-aligned NiCuAg plated front contacts yield an energy conversion efficiency of 19.6%.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999, 020020
Quantitative local efficiency loss analysis on cast-mono PERC solar cells using the DLIT ‘local I-V’ method
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999, 020020
Quantitative local efficiency loss analysis on cast-mono PERC solar cells using the DLIT ‘local I-V’ method
- 21 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 7 (6) , 1541-1550
A Roadmap Toward 24% Efficient PERC Solar Cells in Industrial Mass Production
Many manufacturers choose the passivated emitter and rear cell (PERC) approach in order to surpass the 20% cell efficiency level in mass production. In this paper, we study the efficiency potential of the PERC approach under realistic assumptions for incremental improvements of existing technologies by device simulations. Based on the most recent published experimental results, we find that the PERC structure is able to reach about 24% cell efficiency in mass production by an ongoing sequence of incremental improvements. As a guideline for future developments, we provide a method to improve cell efficiency most effectively by monitoring the current losses at the maximum power point. By means of numerical device modeling, we identify some key technologies toward 24% efficient PERC cells and provide its technology-related target requirements.
- 21 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 7 (6) , 1541-1550
A Roadmap Toward 24% Efficient PERC Solar Cells in Industrial Mass Production
Many manufacturers choose the passivated emitter and rear cell (PERC) approach in order to surpass the 20% cell efficiency level in mass production. In this paper, we study the efficiency potential of the PERC approach under realistic assumptions for incremental improvements of existing technologies by device simulations. Based on the most recent published experimental results, we find that the PERC structure is able to reach about 24% cell efficiency in mass production by an ongoing sequence of incremental improvements. As a guideline for future developments, we provide a method to improve cell efficiency most effectively by monitoring the current losses at the maximum power point. By means of numerical device modeling, we identify some key technologies toward 24% efficient PERC cells and provide its technology-related target requirements.
- Open Access
- 1 September 2017
- Published by Elsevier in Energy Procedia
- Vol. 124, 131-137
Loss analysis of 22% efficient industrial PERC solar cells
- 1 September 2017
- Published by Elsevier in Energy Procedia
- Vol. 124, 131-137
Open AccessLoss analysis of 22% efficient industrial PERC solar cells
- 1 November 2015
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 142, 18-23
Progress in fine-line metallization by co-extrusion printing on cast monosilicon PERC solar cells
- 1 November 2015
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 142, 18-23
Progress in fine-line metallization by co-extrusion printing on cast monosilicon PERC solar cells
- 1 May 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01608371,p. 1-3
Laser-doped silicon solar cells by Laser Chemical Processing (LCP) exceeding 20% efficiency
The introduction of selective emitters underneath the front contacts of solar cells can considerably increase the cell efficiency. Thus, cost-effective fabrication methods for this process step would help to reduce the cost per W p of silicon solar cells. Laser Chemical Processing (LCP) is based on the waterjet-guided laser (LaserMicroJet®) developed and commercialized by Synova S.A., but uses a chemical jet. This technology is able to perform local diffusions at high speed and accuracy without the need of masking or any high-temperature step of the entire wafer. We present experimental investigations on simple device structures to choose optimal laser parameters for selective emitter formation. These parameters are used to fabricate high-efficiency oxide-passivated LFC solar cells that exceed 20% efficiency.
- 1 May 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01608371,p. 1-3
Laser-doped silicon solar cells by Laser Chemical Processing (LCP) exceeding 20% efficiency
The introduction of selective emitters underneath the front contacts of solar cells can considerably increase the cell efficiency. Thus, cost-effective fabrication methods for this process step would help to reduce the cost per W p of silicon solar cells. Laser Chemical Processing (LCP) is based on the waterjet-guided laser (LaserMicroJet®) developed and commercialized by Synova S.A., but uses a chemical jet. This technology is able to perform local diffusions at high speed and accuracy without the need of masking or any high-temperature step of the entire wafer. We present experimental investigations on simple device structures to choose optimal laser parameters for selective emitter formation. These parameters are used to fabricate high-efficiency oxide-passivated LFC solar cells that exceed 20% efficiency.
- Open Access
- 13 April 2007
- Published by Hindawi Limited in Advances in OptoElectronics
- Vol. 2007, 1-15
Industrial Silicon Wafer Solar Cells
In 2006, around 86% of all wafer-based silicon solar cells were produced using screen printing to form the silver front and aluminium rear contacts and chemical vapour deposition to grow silicon nitride as the antireflection coating onto the front surface. This paper reviews this dominant solar cell technology looking into state-of-the-art equipment and corresponding processes for each process step. The main efficiency losses of this type of solar cell are analyzed to demonstrate the future efficiency potential of this technology. In research and development, more various advanced solar cell concepts have demonstrated higher efficiencies. The question which arises is “why are new solar cell concepts not transferred into industrial production more frequently?”. We look into the requirements a new solar cell technology has to fulfill to have an advantage over the current approach. Finally, we give an overview of high-efficiency concepts which have already been transferred into industrial production.
- 13 April 2007
- Published by Hindawi Limited in Advances in OptoElectronics
- Vol. 2007, 1-15
Open AccessIndustrial Silicon Wafer Solar Cells
In 2006, around 86% of all wafer-based silicon solar cells were produced using screen printing to form the silver front and aluminium rear contacts and chemical vapour deposition to grow silicon nitride as the antireflection coating onto the front surface. This paper reviews this dominant solar cell technology looking into state-of-the-art equipment and corresponding processes for each process step. The main efficiency losses of this type of solar cell are analyzed to demonstrate the future efficiency potential of this technology. In research and development, more various advanced solar cell concepts have demonstrated higher efficiencies. The question which arises is “why are new solar cell concepts not transferred into industrial production more frequently?”. We look into the requirements a new solar cell technology has to fulfill to have an advantage over the current approach. Finally, we give an overview of high-efficiency concepts which have already been transferred into industrial production.