Keita Takahashi
Keita Takahashi has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Naoyuki Amemiya
Kyoto University
3 shared publications Takaaki Ibuchi
Division of Electrical, Electronic and Infocommunications Engineering, Graduate School of Engineering, Osaka University
3 shared publicationsTakeshi Yoshiyuki
3 shared publications- Toru Ogitsu
High Energy Accelerator Research Organization (KEK), Tsukuba, Japan
3 shared publications Tsuyoshi Funaki
Division of Electrical, Electronic and Infocommunications Engineering, Graduate School of Engineering, Osaka University
3 shared publicationsKoji Noda
2 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 13 (1) , 70-80
Application of Frequency-Domain Noise-Source Model to Simulation of Time-Synchronized Near-Magnetic-Field Distribution above a Power Circuit
The high-electromagnetic-interference (EMI)-noise area in a power circuit should be clarified when designing a low-EMI-noise power converter. For example, shielding of the power circuit prevents the EMI noise propagation to other circuits via near field couplings. It is important to know the high-EMI-noise area which should be shielded. The EMI noise distribution can be visualized by measuring the near-magnetic-field distribution above the power circuit. However, we cannot measure the near-magnetic-field distribution if there is not enough space for scanning a magnetic field probe between the power circuit and other circuits. Therefore, we propose to adopt a three-dimensional electromagnetic simulation for acquiring the near-magnetic-field distribution above a power circuit. In this paper, we study the validity of the frequency-domain noise-source model for the simulation of the near-magnetic field distribution. We evaluate the near-magnetic-field distribution maps for turn-on and turn-off of the transistor, respectively. The high-EMI-noise area differs depending on frequencies. The high-EMI-noise area for turn-on is different from that for turn-off. We have clarified that each high-EMI-noise area can be predicted by the simulation.
- 1 January 2024
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 13 (1) , 70-80
Open AccessApplication of Frequency-Domain Noise-Source Model to Simulation of Time-Synchronized Near-Magnetic-Field Distribution above a Power Circuit
The high-electromagnetic-interference (EMI)-noise area in a power circuit should be clarified when designing a low-EMI-noise power converter. For example, shielding of the power circuit prevents the EMI noise propagation to other circuits via near field couplings. It is important to know the high-EMI-noise area which should be shielded. The EMI noise distribution can be visualized by measuring the near-magnetic-field distribution above the power circuit. However, we cannot measure the near-magnetic-field distribution if there is not enough space for scanning a magnetic field probe between the power circuit and other circuits. Therefore, we propose to adopt a three-dimensional electromagnetic simulation for acquiring the near-magnetic-field distribution above a power circuit. In this paper, we study the validity of the frequency-domain noise-source model for the simulation of the near-magnetic field distribution. We evaluate the near-magnetic-field distribution maps for turn-on and turn-off of the transistor, respectively. The high-EMI-noise area differs depending on frequencies. The high-EMI-noise area for turn-on is different from that for turn-off. We have clarified that each high-EMI-noise area can be predicted by the simulation.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 63 (3) , 772-782
Noise-Source Model for Frequency-Domain EMI Simulation of a Single-Phased Power Circuit
In recent years, power electronic converters have been downsized significantly by high-density packaging techniques. As a result, parasitic couplings between power electronic components have become larger. For the prediction of electromagnetic interference (EMI) noise considering such couplings, a 3-D electromagnetic simulation is more suitable than a circuit simulation using a huge number of parasitic models. The most-practical electromagnetic simulation method is the finite element method, which is based on a frequency domain. The switching noise must be modeled in the frequency domain for an EMI noise simulation. In this article, we propose a new noise-source model for a frequency-domain EMI noise simulation. We modeled a transistor and a freewheeling diode by voltage and current sources based on three model topologies: transistor-off-diode-on topology (off-topology); transistor-on-diode-off topology (on-topology); and transistor-on-diode-on topology (recovery topology). We also used off-topology to simulate the turn-off EMI noise as caused by the turning-off of a transistor. Meanwhile, we used a combination of on-topology and recovery topology to simulate the turn-on EMI noise including recovery noise as caused by the turning-on of a transistor. After introducing the details of the model, we compared the measured and simulated results so as to show the validity of the model.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 63 (3) , 772-782
Noise-Source Model for Frequency-Domain EMI Simulation of a Single-Phased Power Circuit
In recent years, power electronic converters have been downsized significantly by high-density packaging techniques. As a result, parasitic couplings between power electronic components have become larger. For the prediction of electromagnetic interference (EMI) noise considering such couplings, a 3-D electromagnetic simulation is more suitable than a circuit simulation using a huge number of parasitic models. The most-practical electromagnetic simulation method is the finite element method, which is based on a frequency domain. The switching noise must be modeled in the frequency domain for an EMI noise simulation. In this article, we propose a new noise-source model for a frequency-domain EMI noise simulation. We modeled a transistor and a freewheeling diode by voltage and current sources based on three model topologies: transistor-off-diode-on topology (off-topology); transistor-on-diode-off topology (on-topology); and transistor-on-diode-on topology (recovery topology). We also used off-topology to simulate the turn-off EMI noise as caused by the turning-off of a transistor. Meanwhile, we used a combination of on-topology and recovery topology to simulate the turn-on EMI noise including recovery noise as caused by the turning-on of a transistor. After introducing the details of the model, we compared the measured and simulated results so as to show the validity of the model.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEICE Transactions on Communications
- Vol. E102.B (9) , 1853-1861
Frequency-Domain EMI Simulation of Power Electronic Converter with Voltage-Source and Current-Source Noise Models
The electromagnetic interference (EMI) generated by power electronic converters is largely influenced by parasitic inductances and capacitances of the converter. One of the most popular EMI simulation methods that can take account of the parasitic parameters is the three-dimensional electromagnetic simulation by finite element method (FEM). A noise-source model should be given in the frequency domain in comprehensive FEM simulations. However, the internal impedance of the noise source is static in the frequency domain, whereas the transient switching of a power semiconductor changes its internal resistance in the time domain. In this paper, we propose the use of a voltage-source noise model and a current-source noise model to simulate EMI noise with the two components of voltage-dependent noise and current-dependent noise in the frequency domain. In order to simulate voltage-dependent EMI noise, we model the power semiconductor that is turning on by a voltage source, whose internal impedance is low. The voltage-source noise is proportional to the amplitude of the voltage. In order to simulate current-dependent EMI noise, we model the power semiconductor that is turning off by a current source, whose internal impedance is large. The current-source noise is proportional to the amplitude of the current. The measured and simulated conducted EMI agreed very well.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEICE Transactions on Communications
- Vol. E102.B (9) , 1853-1861
Frequency-Domain EMI Simulation of Power Electronic Converter with Voltage-Source and Current-Source Noise Models
The electromagnetic interference (EMI) generated by power electronic converters is largely influenced by parasitic inductances and capacitances of the converter. One of the most popular EMI simulation methods that can take account of the parasitic parameters is the three-dimensional electromagnetic simulation by finite element method (FEM). A noise-source model should be given in the frequency domain in comprehensive FEM simulations. However, the internal impedance of the noise source is static in the frequency domain, whereas the transient switching of a power semiconductor changes its internal resistance in the time domain. In this paper, we propose the use of a voltage-source noise model and a current-source noise model to simulate EMI noise with the two components of voltage-dependent noise and current-dependent noise in the frequency domain. In order to simulate voltage-dependent EMI noise, we model the power semiconductor that is turning on by a voltage source, whose internal impedance is low. The voltage-source noise is proportional to the amplitude of the voltage. In order to simulate current-dependent EMI noise, we model the power semiconductor that is turning off by a current source, whose internal impedance is large. The current-source noise is proportional to the amplitude of the current. The measured and simulated conducted EMI agreed very well.
- 27 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 61 (5) , 1663-1672
Mechanism of Near-Field Coupling Between Noise Source and EMI Filter in Power Electronic Converter and Its Required Shielding
When designing a low electromagnetic interference (EMI) power electronic converter with high packaging density, its internal near-field coupling to an EMI filter is critical. In this paper, we investigated the near-field coupling between a noise source and a single-phase EMI filter. First, we measured the common-mode (CM) and differential-mode (DM) couplings separately using a four-port network analyzer. The DM coupling when the EMI filter was exposed to a magnetic field was larger than that when it was exposed to an electric field. On the other hand, the CM coupling when the EMI filter was exposed to an electric field was larger than that when it was exposed to a magnetic field. Second, we extracted parasitic coupling elements that determine the coupling magnitude of each mode of coupling. The coupling calculated by the extracted elements agreed with the measurement well. We identified the dominant coupling path between the noise source and the EMI filter. Finally, we studied the required shielding of the EMI filter to reduce the coupling efficiently. Consequently, we found that most of the coupling can be eliminated by shielding the dominant coupling path.
- 27 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 61 (5) , 1663-1672
Mechanism of Near-Field Coupling Between Noise Source and EMI Filter in Power Electronic Converter and Its Required Shielding
When designing a low electromagnetic interference (EMI) power electronic converter with high packaging density, its internal near-field coupling to an EMI filter is critical. In this paper, we investigated the near-field coupling between a noise source and a single-phase EMI filter. First, we measured the common-mode (CM) and differential-mode (DM) couplings separately using a four-port network analyzer. The DM coupling when the EMI filter was exposed to a magnetic field was larger than that when it was exposed to an electric field. On the other hand, the CM coupling when the EMI filter was exposed to an electric field was larger than that when it was exposed to a magnetic field. Second, we extracted parasitic coupling elements that determine the coupling magnitude of each mode of coupling. The coupling calculated by the extracted elements agreed with the measurement well. We identified the dominant coupling path between the noise source and the EMI filter. Finally, we studied the required shielding of the EMI filter to reduce the coupling efficiently. Consequently, we found that most of the coupling can be eliminated by shielding the dominant coupling path.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Practical Mobile-DBA Scheme Considering Data Arrival Period for 5G Mobile Fronthaul with TDM-PON
For mobile fronthaul with TDM-PON, we propose a practical DBA scheme that allocates proper time slots by estimating the data-arrival period from mobile scheduling information. Experiments show that the scheme actually satisfies the fronthaul latency requirement for the first time.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Practical Mobile-DBA Scheme Considering Data Arrival Period for 5G Mobile Fronthaul with TDM-PON
For mobile fronthaul with TDM-PON, we propose a practical DBA scheme that allocates proper time slots by estimating the data-arrival period from mobile scheduling information. Experiments show that the scheme actually satisfies the fronthaul latency requirement for the first time.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Frequency domain simulation of conducted EMI in power electronic converters considering internal near field couplings by FEM
Power electronic components such as busbars, capacitors, and inductors are positioned close to each other when designing a high power density converter. Therefore, the internal near field couplings between these components should be considered when designing a low electromagnetic interference (EMI) converter. In this paper, we propose a new frequency domain model for simulation of EMI in power electronic converters. We focused on frequency domain simulation to assess the internal couplings by finite element method (FEM) full wave simulation without requiring a complicated equivalent circuit model. In order to simulate both the transient voltage noise (dv/dt noise) and transient current noise (di/dt noise), we used two noise source models (a voltage source noise model and a current source noise model). We compared the measured and simulated EMI to confirm the validity of our model, and found good agreement.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Frequency domain simulation of conducted EMI in power electronic converters considering internal near field couplings by FEM
Power electronic components such as busbars, capacitors, and inductors are positioned close to each other when designing a high power density converter. Therefore, the internal near field couplings between these components should be considered when designing a low electromagnetic interference (EMI) converter. In this paper, we propose a new frequency domain model for simulation of EMI in power electronic converters. We focused on frequency domain simulation to assess the internal couplings by finite element method (FEM) full wave simulation without requiring a complicated equivalent circuit model. In order to simulate both the transient voltage noise (dv/dt noise) and transient current noise (di/dt noise), we used two noise source models (a voltage source noise model and a current source noise model). We compared the measured and simulated EMI to confirm the validity of our model, and found good agreement.
- 24 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 59 (6) , 1880-1886
Analysis of Parasitic Couplings in EMI Filters and Coupling Reduction Methods
In this paper, the effects of parasitic couplings in electromagnetic interference (EMI) filters are investigated using an equivalent circuit analysis and experiments. The investigated filter has the C-L-C filter structure which is composed of foil capacitors, feedthrough capacitors, and a toroidal inductor. The parasitic couplings between input capacitors and output capacitors increase the transfer function of the filter. We found that the increase of the transfer function is caused by two kinds of parasitic couplings: one is the parasitic inductive coupling between the two resonance circuits which are composed of feedthrough capacitors and foil capacitors, and another is the parasitic capacitive coupling between the input and the output foil capacitors. Balancing the two parasitic couplings, it is possible to reduce the transfer function increase without increasing the filter size. The experimental results of transfer functions agree with the equivalent circuit analysis results up to 30 MHz. The balancing condition obtained by the circuit analysis has been confirmed by the experiments.
- 24 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 59 (6) , 1880-1886
Analysis of Parasitic Couplings in EMI Filters and Coupling Reduction Methods
In this paper, the effects of parasitic couplings in electromagnetic interference (EMI) filters are investigated using an equivalent circuit analysis and experiments. The investigated filter has the C-L-C filter structure which is composed of foil capacitors, feedthrough capacitors, and a toroidal inductor. The parasitic couplings between input capacitors and output capacitors increase the transfer function of the filter. We found that the increase of the transfer function is caused by two kinds of parasitic couplings: one is the parasitic inductive coupling between the two resonance circuits which are composed of feedthrough capacitors and foil capacitors, and another is the parasitic capacitive coupling between the input and the output foil capacitors. Balancing the two parasitic couplings, it is possible to reduce the transfer function increase without increasing the filter size. The experimental results of transfer functions agree with the equivalent circuit analysis results up to 30 MHz. The balancing condition obtained by the circuit analysis has been confirmed by the experiments.
- 10 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 716-721
Simulation of shielding performance against near field coupling to EMI filter for power electronic converter using FEM
When designing an Electromagnetic interference (EMI) filter for power electronic converters, we should consider the shielding performance against the external near field coupling to the EMI filter as well as the attenuation performance. In this paper, we studied the validity of the Finite Element Method (FEM) simulation of the EMI filter for predicting the shielding performance before a trial manufacture. First, we created models of capacitors and common mode choke coils which can simulate their impedance characteristics. Next, using these component models, the assembled EMI filter model was created. We compared the measured and simulated results to verify the model. The shielding performance was evaluated using a loop coil as an external near field source. Consequently, the simulated results agreed with the measured results well.
- 10 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 716-721
Simulation of shielding performance against near field coupling to EMI filter for power electronic converter using FEM
When designing an Electromagnetic interference (EMI) filter for power electronic converters, we should consider the shielding performance against the external near field coupling to the EMI filter as well as the attenuation performance. In this paper, we studied the validity of the Finite Element Method (FEM) simulation of the EMI filter for predicting the shielding performance before a trial manufacture. First, we created models of capacitors and common mode choke coils which can simulate their impedance characteristics. Next, using these component models, the assembled EMI filter model was created. We compared the measured and simulated results to verify the model. The shielding performance was evaluated using a loop coil as an external near field source. Consequently, the simulated results agreed with the measured results well.
- 1 November 2012
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 482, 74-79
Research and development of fundamental technologies for accelerator magnets using high Tc superconductors
- 1 November 2012
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 482, 74-79
Research and development of fundamental technologies for accelerator magnets using high Tc superconductors
- Open Access
- 21 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 22 (3) , 4901705
Magnetic Field Design of Coil-Dominated Magnets Wound With Coated Conductors
Coil-dominated magnets wound with coated conductors were designed for an FFAG accelerator for carbon therapy, which was designed by applying linear approximation. When designing the coil-end of the magnets, we applied differential geometry. To apply the differential geometry to three-dimensional windings with coated conductors, we introduced the concept of generalized flat-wise bending. Thereby, the combination of flat-wise bending and torsion was considered as bending of developable surface. Generated magnetic field was calculated, and the positions of conductors were optimized to minimize the field error. Three dimensional shapes of magnets were successfully designed with constraints on generalized flat-wise bending and edge-wise bending of coated conductors.
- 21 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 22 (3) , 4901705
Open AccessMagnetic Field Design of Coil-Dominated Magnets Wound With Coated Conductors
Coil-dominated magnets wound with coated conductors were designed for an FFAG accelerator for carbon therapy, which was designed by applying linear approximation. When designing the coil-end of the magnets, we applied differential geometry. To apply the differential geometry to three-dimensional windings with coated conductors, we introduced the concept of generalized flat-wise bending. Thereby, the combination of flat-wise bending and torsion was considered as bending of developable surface. Generated magnetic field was calculated, and the positions of conductors were optimized to minimize the field error. Three dimensional shapes of magnets were successfully designed with constraints on generalized flat-wise bending and edge-wise bending of coated conductors.