Banti Amarshah Gedam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Banti Amarshah Gedam has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Akhil Upadhyay
Indian Institute of Technology Roorkee
2 shared publicationsAditya Milmile
Advanced Concrete, Steel & Composites (ACSC) Group, CSIR – Central Building Research Institute, Roorkee 247667, India 2. Department of Civil Engineering, Visvesvaraya National Institute of Technology, Nagpur 440010, India
1 shared publication- Ananda Mitra
Department of Civil Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, India
1 shared publication N. M. Bhandari
Indian Institute of Technology Jodhpur
1 shared publicationN.M. Bhandari
1 shared publication- Rajesh Kumar
CSIR- Central Building Research Institute Roorkee, Uttarakhand, 247667, India
1 shared publication
Latest Publications
- Open Access
- 24 October 2025
- Published by Bilingual Publishing Group in Journal of Building Material Science
- p. 16-28
Investigation of Mechanical Properties of High-Performance Steel and Polypropylene Fiber Reinforced Concrete
Fiber reinforcement significantly enhances the strength, toughness, and durability of concrete by reducing the propagation of microcracks in the concrete matrix. With the rising demand for high-performance concrete (HPC), this study investigates the mechanical properties of HPC with varying proportions of polypropylene (PP) and steel (ST) fibers. Supplementary cementitious materials (SCMs) toward partial replacement of ordinary Portland cement (OPC) were incorporated to prepare HPC mixes as a ternary composite system using Fly Ash (FA), Silica Fume (SF), and Ground Granulated Blast Furnace Slag (GGBS). Each HPC mix comprised two SCMs, accounting for 20% of the mass fraction of the OPC binder. The study encompassed fiber percentages ranging from 0 to 0.075% PP and 0 to 2% ST, incorporating them into the HPC mixes with gradual increases of 0.025% for PP and 0.5% for ST fiber by mass fraction. All HPC mixes were tested for mechanical properties using compressive and split tensile strength tests. The influence of SCMs on HPC was studied using X-ray diffraction (XRD) for microstructural analyses. It was found that the compressive and split tensile strengths of HPC increased up to an optimal fiber percentage and then decreased. A comparison of the test results of high-performance fiber-reinforced concrete with those of plain HPC revealed significant improvements in compressive and splitting tensile strengths by 26.59% and 57.74%, respectively. Also, the XRD analysis revealed that the composition of the SCMs in HPC was a significant and effective solution for the mechanical properties of the concrete.
- 24 October 2025
- Published by Bilingual Publishing Group in Journal of Building Material Science
- p. 16-28
Open AccessInvestigation of Mechanical Properties of High-Performance Steel and Polypropylene Fiber Reinforced Concrete
Fiber reinforcement significantly enhances the strength, toughness, and durability of concrete by reducing the propagation of microcracks in the concrete matrix. With the rising demand for high-performance concrete (HPC), this study investigates the mechanical properties of HPC with varying proportions of polypropylene (PP) and steel (ST) fibers. Supplementary cementitious materials (SCMs) toward partial replacement of ordinary Portland cement (OPC) were incorporated to prepare HPC mixes as a ternary composite system using Fly Ash (FA), Silica Fume (SF), and Ground Granulated Blast Furnace Slag (GGBS). Each HPC mix comprised two SCMs, accounting for 20% of the mass fraction of the OPC binder. The study encompassed fiber percentages ranging from 0 to 0.075% PP and 0 to 2% ST, incorporating them into the HPC mixes with gradual increases of 0.025% for PP and 0.5% for ST fiber by mass fraction. All HPC mixes were tested for mechanical properties using compressive and split tensile strength tests. The influence of SCMs on HPC was studied using X-ray diffraction (XRD) for microstructural analyses. It was found that the compressive and split tensile strengths of HPC increased up to an optimal fiber percentage and then decreased. A comparison of the test results of high-performance fiber-reinforced concrete with those of plain HPC revealed significant improvements in compressive and splitting tensile strengths by 26.59% and 57.74%, respectively. Also, the XRD analysis revealed that the composition of the SCMs in HPC was a significant and effective solution for the mechanical properties of the concrete.
- 17 October 2025
- Published by Springer Nature
- p. 93-104
Experimental Study on the Spalling Behavior of High-Performance Concrete at Elevated Temperature
- 17 October 2025
- Published by Springer Nature
- p. 93-104
Experimental Study on the Spalling Behavior of High-Performance Concrete at Elevated Temperature
- 27 November 2024
- Published by Springer Nature
- p. 467-480
Thermally Induced Concrete Properties at Elevated Temperature
- 27 November 2024
- Published by Springer Nature
- p. 467-480
Thermally Induced Concrete Properties at Elevated Temperature
- 1 October 2021
- Published by Elsevier in Structures
- Vol. 33, 855-877
Fire resistance design method for reinforced concrete beams to evaluate fire-resistance rating
- 1 October 2021
- Published by Elsevier in Structures
- Vol. 33, 855-877
Fire resistance design method for reinforced concrete beams to evaluate fire-resistance rating
- 1 December 2019
- Published by Elsevier in Engineering Structures
- Vol. 201
Time-dependent behaviour prediction of the prestressed HPC I-girder
- 1 December 2019
- Published by Elsevier in Engineering Structures
- Vol. 201
Time-dependent behaviour prediction of the prestressed HPC I-girder
- 12 July 2017
- Published by Springer Nature
- p. 254-264
Time-Dependent Behavior Prediction, Serviceability and Sustainability Problems for High-Performance Concrete Bridges
- 12 July 2017
- Published by Springer Nature
- p. 254-264
Time-Dependent Behavior Prediction, Serviceability and Sustainability Problems for High-Performance Concrete Bridges
- 10 October 2014
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 52 (1) , 97-113
An apt material model for drying shrinkage and specific creep of HPC using artificial neural network
- 10 October 2014
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 52 (1) , 97-113
An apt material model for drying shrinkage and specific creep of HPC using artificial neural network