Kuldeep Singh Gour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kuldeep Singh Gour has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Jin Hyeok Kim
Chonnam National University
8 shared publications - Vidya Nand Singh
CSIR- National Physical Laboratory, K.S. Krishnan Marg, New Delhi, India
8 shared publications Om Pal Singh
Academy of Scientific and Innovative Research (AcSIR), Indian Reference Materials Division, Council for Scientific and Industrial Research (CSIR)-National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi 110012, India
7 shared publicationsRahul Parmar
Physics Division School of Science and Technology University of Camerino 62032 Camerino (MC) Italy
6 shared publicationsJongsung Park
Department of Energy Engineering, Department of Energy System Engineering
5 shared publicationsJun Sung Jang
Optoelectronics Convergence Research Center and Department of Materials Science and Engineering Chonnam National University Gwangju 61186 Republic of Korea
5 shared publications
Latest Publications
- 6 October 2026
- Published by Wiley in Chemistry – An Asian Journal
- Vol. 21 (19) , e71007
Experimental, DFT, and SCAPS‐1D Investigation of Sulfur‐Incorporated Sb 2 Se 3 Powders for Photovoltaic Applications
Antimony selenide (Sb 2 Se 3 ) is a promising photoabsorber material for photovoltaics (PVs) owing to its favorable properties, including a high absorption coefficient, an optimal bandgap, earth‐abundant constituents, and low toxicity. In this study, sulfur (S)‐incorporated Sb 2 Se 3 powders were synthesized by substituting Se with S using a solid‐state method. Structural, morphological, and optical analyses showed that increasing sulfur content widened the bandgap from 1.10 to 1.54 eV. Furthermore, DFT calculations supported the experimental bandgap trend. SCAPS‐1D simulations indicated that higher bandgaps increase open‐circuit voltage ( V oc ) but short‐circuit current density ( J sc ), with optimal performance at 1.362 eV. The simulated device achieved power conversion efficiency (PCE) of 24.31%, V oc of 0.899 V, J sc of 32.92 mAcm −2 , and FF of 82.06%. These results highlight sulfur incorporation as an effective approach for tuning the properties of Sb 2 Se 3 ‐based PVs.
- 6 October 2026
- Published by Wiley in Chemistry – An Asian Journal
- Vol. 21 (19) , e71007
Experimental, DFT, and SCAPS‐1D Investigation of Sulfur‐Incorporated Sb 2 Se 3 Powders for Photovoltaic Applications
Antimony selenide (Sb 2 Se 3 ) is a promising photoabsorber material for photovoltaics (PVs) owing to its favorable properties, including a high absorption coefficient, an optimal bandgap, earth‐abundant constituents, and low toxicity. In this study, sulfur (S)‐incorporated Sb 2 Se 3 powders were synthesized by substituting Se with S using a solid‐state method. Structural, morphological, and optical analyses showed that increasing sulfur content widened the bandgap from 1.10 to 1.54 eV. Furthermore, DFT calculations supported the experimental bandgap trend. SCAPS‐1D simulations indicated that higher bandgaps increase open‐circuit voltage ( V oc ) but short‐circuit current density ( J sc ), with optimal performance at 1.362 eV. The simulated device achieved power conversion efficiency (PCE) of 24.31%, V oc of 0.899 V, J sc of 32.92 mAcm −2 , and FF of 82.06%. These results highlight sulfur incorporation as an effective approach for tuning the properties of Sb 2 Se 3 ‐based PVs.
- 25 September 2026
- Published by Wiley in Advanced Materials Technologies
Multimodality of Antimony Selenide: Emerging Multifunctional Semiconductor for Optoelectronics, Photonics, Catalysis, and Biomedical Applications
Semiconducting materials are central to a wide range of technologies, from everyday electronics to advanced artificial intelligence systems. In recent years, significant research has focused on identifying alternatives to conventional semiconductors. Among these, Antimony Selenide (Sb 2 Se 3 ) is a promising p‐type semiconductor (which can also be converted to n‐type via doping) with a tunable bandgap of 1.1–1.7 eV, excellent broadband near‐infrared (NIR) optical absorption, including in the telecommunication wavelength range, and high stability. Its strong chemical robustness and environmentally friendly, non‐toxic composition make it an attractive candidate for a wide range of applications, including optoelectronics, photonics, catalysis, and biomedicine. This detailed review highlights recent advances in Sb 2 Se 3 ‐based devices, emphasizing the materials engineering, including synthesis methods, heterostructure formation with other materials, and device fabrication strategies. Special focus is placed on key applications in solar cells, photodetectors, photonics, catalysis, and biomedical applications. Finally, the present review provides an updated perspective on the fundamental science of Sb 2 Se 3, along with future directions and recommendations for designing Sb 2 Se 3 materials based on various devices. The primary focus is to bridge the gap between fundamental understanding and practical application, providing an updated overview of innovations in Sb 2 Se 3 materials that is accessible to a broader readership.
- 25 September 2026
- Published by Wiley in Advanced Materials Technologies
Multimodality of Antimony Selenide: Emerging Multifunctional Semiconductor for Optoelectronics, Photonics, Catalysis, and Biomedical Applications
Semiconducting materials are central to a wide range of technologies, from everyday electronics to advanced artificial intelligence systems. In recent years, significant research has focused on identifying alternatives to conventional semiconductors. Among these, Antimony Selenide (Sb 2 Se 3 ) is a promising p‐type semiconductor (which can also be converted to n‐type via doping) with a tunable bandgap of 1.1–1.7 eV, excellent broadband near‐infrared (NIR) optical absorption, including in the telecommunication wavelength range, and high stability. Its strong chemical robustness and environmentally friendly, non‐toxic composition make it an attractive candidate for a wide range of applications, including optoelectronics, photonics, catalysis, and biomedicine. This detailed review highlights recent advances in Sb 2 Se 3 ‐based devices, emphasizing the materials engineering, including synthesis methods, heterostructure formation with other materials, and device fabrication strategies. Special focus is placed on key applications in solar cells, photodetectors, photonics, catalysis, and biomedical applications. Finally, the present review provides an updated perspective on the fundamental science of Sb 2 Se 3, along with future directions and recommendations for designing Sb 2 Se 3 materials based on various devices. The primary focus is to bridge the gap between fundamental understanding and practical application, providing an updated overview of innovations in Sb 2 Se 3 materials that is accessible to a broader readership.
- Open Access
- 30 July 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (8) , 919
Sputtered Piezoelectric AlN Thin Films: Parameter Optimisation, Deposition Challenges, and Emerging Perspectives—A Review
This article reviews the reactive magnetron sputtering of piezoelectric Aluminium Nitride (AlN) thin films, with a focus on process parameter optimisation and system-level deposition challenges. AlN is a leading material for MEMS and RF applications owing to its c-axis (002) orientation, high acoustic velocity, wide bandgap (∼6.2 eV), and CMOS compatibility. We review the influence of sputtering power, nitrogen flow ratio, substrate temperature, and target-to-substrate distance on crystallographic quality and document practical hardware challenges, including vacuum leakage, grounding faults, target erosion, and mass flow controller drift, that critically affect reproducibility but are systematically underreported in the literature. A perspective is provided on emerging application domains where optimised AlN films address current performance gaps, including next-generation RF/telecom systems towards 6G and Future Networks, harsh environment sensing and actuation, biomedical ultrasound, and IoT energy harvesting. The complementarity between AlN and Silicon Carbide (SiC) is discussed for high-temperature, high-power, and radiation-hard MEMS, where AlN/SiC heterostructures combine the piezoelectric activity of AlN with the mechanical and chemical robustness of SiC. It also incorporates a discussion of dopant- and heteroepitaxy-based AlN engineering, AlN deposition on a wider range of substrates, the role of seed and electrode underlayers, and pulsed-DC sputtering as a third power supply mode alongside RF and conventional DC.
- 30 July 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (8) , 919
Open AccessSputtered Piezoelectric AlN Thin Films: Parameter Optimisation, Deposition Challenges, and Emerging Perspectives—A Review
This article reviews the reactive magnetron sputtering of piezoelectric Aluminium Nitride (AlN) thin films, with a focus on process parameter optimisation and system-level deposition challenges. AlN is a leading material for MEMS and RF applications owing to its c-axis (002) orientation, high acoustic velocity, wide bandgap (∼6.2 eV), and CMOS compatibility. We review the influence of sputtering power, nitrogen flow ratio, substrate temperature, and target-to-substrate distance on crystallographic quality and document practical hardware challenges, including vacuum leakage, grounding faults, target erosion, and mass flow controller drift, that critically affect reproducibility but are systematically underreported in the literature. A perspective is provided on emerging application domains where optimised AlN films address current performance gaps, including next-generation RF/telecom systems towards 6G and Future Networks, harsh environment sensing and actuation, biomedical ultrasound, and IoT energy harvesting. The complementarity between AlN and Silicon Carbide (SiC) is discussed for high-temperature, high-power, and radiation-hard MEMS, where AlN/SiC heterostructures combine the piezoelectric activity of AlN with the mechanical and chemical robustness of SiC. It also incorporates a discussion of dopant- and heteroepitaxy-based AlN engineering, AlN deposition on a wider range of substrates, the role of seed and electrode underlayers, and pulsed-DC sputtering as a third power supply mode alongside RF and conventional DC.
- Open Access
- 5 August 2025
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 7 (4)
Advancements in AgBiS2 thin film solar cells: strategies, challenges, and perspectives
Recently, ternary chalcogenide AgBiS2 (ABS) gained enormous attention as it is considered an eco-friendly, non-toxic, and cost-effective alternative as a photo-absorber for photovoltaics (PVs) owing to its excellent optoelectronic properties, i.e., a high absorption coefficient (>105 cm-1), tunable bandgap, and environmental stability. Unlike CuInGa(S,Se)2 (CIGSSe), perovskites, and other materials, the ultrathin layer of AgBiS2 thickness is about 35 nm, enough to absorb a significant portion of the solar spectrum, making it advantageous for PVs. However, the power conversion efficiency (PCE) of AgBiS2 thin film solar cells (TFSCs) has been reported to be around ~11% lower than that of CIGSSe (23.35%). This review highlights the latest strategies for further advancement in the performance of AgBiS2 TFSCs, mainly focusing on the intrinsic properties of AgBiS2, absorber synthesis methods, device fabrication techniques, challenges, and prospects. Herein, innovative strategies, such as device design, bandgap engineering, doping, surface/interface passivation, and integrating mesoporous layers, are reviewed. Furthermore, the review outlines a roadmap for developing high-efficiency and commercially viable AgBiS2-based PVs for a next-generation sustainable future.
- 5 August 2025
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 7 (4)
Open AccessAdvancements in AgBiS2 thin film solar cells: strategies, challenges, and perspectives
Recently, ternary chalcogenide AgBiS2 (ABS) gained enormous attention as it is considered an eco-friendly, non-toxic, and cost-effective alternative as a photo-absorber for photovoltaics (PVs) owing to its excellent optoelectronic properties, i.e., a high absorption coefficient (>105 cm-1), tunable bandgap, and environmental stability. Unlike CuInGa(S,Se)2 (CIGSSe), perovskites, and other materials, the ultrathin layer of AgBiS2 thickness is about 35 nm, enough to absorb a significant portion of the solar spectrum, making it advantageous for PVs. However, the power conversion efficiency (PCE) of AgBiS2 thin film solar cells (TFSCs) has been reported to be around ~11% lower than that of CIGSSe (23.35%). This review highlights the latest strategies for further advancement in the performance of AgBiS2 TFSCs, mainly focusing on the intrinsic properties of AgBiS2, absorber synthesis methods, device fabrication techniques, challenges, and prospects. Herein, innovative strategies, such as device design, bandgap engineering, doping, surface/interface passivation, and integrating mesoporous layers, are reviewed. Furthermore, the review outlines a roadmap for developing high-efficiency and commercially viable AgBiS2-based PVs for a next-generation sustainable future.
- 6 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (24) , 35382-35395
Machine Learning Drives a Path to Defect Engineering for Suppressing Nonradiative Recombination Losses in Cu2ZnSn(S,Se)4 Solar Cells
Recent kesterite developments encouraged researchers to use Cu2ZnSn(S,Se)4 (CZTSSe)-based photoabsorber materials in diverse optoelectronic applications. However, the detrimental bulk and interface defects induced high carrier recombination at corresponding regions, stagnating further improvement in the performance of kesterite solar cells. In this work, a machine learning (ML)-guided strategy is employed to optimize the amount of germanium (Ge) incorporation to enhance the baseline performance of CZTSSe. The ML model indicates that incorporation of VOC) loss. It also revealed that engineering defects controlling carrier density plays a crucial role in achieving high-quality devices. Building upon the optimized Ge incorporation, silver (Ag) is subsequently introduced to further passivate shallow-level copper (Cu)-related defects. Experimental validation confirms that Ge incorporation effectively improves the device performance by suppressing deep-level defects in both the space-charge region and the quasi-neutral region. As a result, an improved carrier separation process, minority carrier lifetime, and reduced nonradiative carrier recombination losses increased device performance by more than 20%. Finally, the champion device with double-cation incorporation of Ag and Ge in the vacuum-proceeded CZTSSe absorber layer delivers enhanced device performance from 9.11 to 11.32%.
- 6 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (24) , 35382-35395
Machine Learning Drives a Path to Defect Engineering for Suppressing Nonradiative Recombination Losses in Cu2ZnSn(S,Se)4 Solar Cells
Recent kesterite developments encouraged researchers to use Cu2ZnSn(S,Se)4 (CZTSSe)-based photoabsorber materials in diverse optoelectronic applications. However, the detrimental bulk and interface defects induced high carrier recombination at corresponding regions, stagnating further improvement in the performance of kesterite solar cells. In this work, a machine learning (ML)-guided strategy is employed to optimize the amount of germanium (Ge) incorporation to enhance the baseline performance of CZTSSe. The ML model indicates that incorporation of VOC) loss. It also revealed that engineering defects controlling carrier density plays a crucial role in achieving high-quality devices. Building upon the optimized Ge incorporation, silver (Ag) is subsequently introduced to further passivate shallow-level copper (Cu)-related defects. Experimental validation confirms that Ge incorporation effectively improves the device performance by suppressing deep-level defects in both the space-charge region and the quasi-neutral region. As a result, an improved carrier separation process, minority carrier lifetime, and reduced nonradiative carrier recombination losses increased device performance by more than 20%. Finally, the champion device with double-cation incorporation of Ag and Ge in the vacuum-proceeded CZTSSe absorber layer delivers enhanced device performance from 9.11 to 11.32%.
- 6 December 2024
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 7 (24) , 28074-28097
Nanoporous Metal–Organic Frameworks for Electroreduction of Nitrogen and Carbon Dioxide: A Review
- 6 December 2024
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 7 (24) , 28074-28097
Nanoporous Metal–Organic Frameworks for Electroreduction of Nitrogen and Carbon Dioxide: A Review
- Open Access
- 16 February 2024
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 5 (8) , 3220-3227
Detrapping of the carriers from shallow states in a highly responsive, fast, broadband (UV-vis-NIR), self-powered SnSe/Si photodetector with asymmetric metal electrodes
Bias-dependent trapping and de-trapping can be seen in the SnSe device. At low bias, voltage trapping of the carriers can be seen in the device; they start to de-trap after 500 mV bias.
- 16 February 2024
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 5 (8) , 3220-3227
Open AccessDetrapping of the carriers from shallow states in a highly responsive, fast, broadband (UV-vis-NIR), self-powered SnSe/Si photodetector with asymmetric metal electrodes
Bias-dependent trapping and de-trapping can be seen in the SnSe device. At low bias, voltage trapping of the carriers can be seen in the device; they start to de-trap after 500 mV bias.
In Search of Disorder Transitions and Defects Within Cu2ZnSn(S,Se)4‐Based Absorber Layers via Temperature‐Dependent Raman Spectroscopy Technique
The temperature‐dependent (25–300 °C) disorder transitions analyzed via Raman spectroscopic technique for the different non‐stoichiometric Cu2ZnSn(S,Se)4 (CZTSSe) thin films are demonstrated. In the thin films prepared with different Zn conditions, i.e., in Zn‐1 (Zn‐poor), the density of the A‐type defect cluster [ZnCu + VCu] increases with temperature; however, it slightly decreases and remains constant for Zn‐rich samples, i.e., Zn‐2 and Zn‐3. At the same time, the density of the B‐type defect cluster [2ZnCu + ZnSn] increases with increasing temperature and Zn content. The observations further reveal that Zn concentration has less impact on VCu formation; therefore, above the optimum Cu‐poor and Zn‐rich conditions, ZnCu shallow donors negatively influence the kesterite device performances. Finally, solar cells based on all the CZTSSe thin‐film samples (Zn‐1, Zn‐2, and Zn‐3) are fabricated in which a device based on Zn‐2 exhibits excellent power conversion efficiency of ≈11.0% with open‐circuit voltage of 478 mV, short‐circuit current of 35.51 mA cm−2, and fill factor of 64%, respectively.
In Search of Disorder Transitions and Defects Within Cu2ZnSn(S,Se)4‐Based Absorber Layers via Temperature‐Dependent Raman Spectroscopy Technique
The temperature‐dependent (25–300 °C) disorder transitions analyzed via Raman spectroscopic technique for the different non‐stoichiometric Cu2ZnSn(S,Se)4 (CZTSSe) thin films are demonstrated. In the thin films prepared with different Zn conditions, i.e., in Zn‐1 (Zn‐poor), the density of the A‐type defect cluster [ZnCu + VCu] increases with temperature; however, it slightly decreases and remains constant for Zn‐rich samples, i.e., Zn‐2 and Zn‐3. At the same time, the density of the B‐type defect cluster [2ZnCu + ZnSn] increases with increasing temperature and Zn content. The observations further reveal that Zn concentration has less impact on VCu formation; therefore, above the optimum Cu‐poor and Zn‐rich conditions, ZnCu shallow donors negatively influence the kesterite device performances. Finally, solar cells based on all the CZTSSe thin‐film samples (Zn‐1, Zn‐2, and Zn‐3) are fabricated in which a device based on Zn‐2 exhibits excellent power conversion efficiency of ≈11.0% with open‐circuit voltage of 478 mV, short‐circuit current of 35.51 mA cm−2, and fill factor of 64%, respectively.
- 26 October 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (44) , 23831-23842
Overcoming the limitations of low-bandgap Cu2ZnSn(S,Se)4devices under indoor light conditions: from design to prototype IoT application
With the growing need for cost-effective and sustainable Internet of things (IoT) technologies, kesterite-based solar cells are gaining popularity. We report the fabrication of an efficient CZTSSe absorber layer with improved Voc loss and its possible use in indoor photovoltaic applications. The double cation incorporation (co-doping) approach is employed with Ag and Ge to achieve this. The devices fabricated and tested under standard illumination (1 sun) and low light intensity conditions showed enhanced device performances and lower Voc losses after co-doping. Under indoor light conditions, Voc of 290 mV with white LED (WLED) and 310 mV with fluorescent lamp (FL-4000K) was achieved at the lowest intensity of 400 lux, while a value exceeding 350 mV was obtained at 1200 lux with FL-4000K for the CZTSSe:Ag–Ge device. Voc recoveries of >60% under all intensity conditions and >70% at 1200 lux with both WLED and FL-4000K were achieved. Moreover, the CZTSSe:Ag–Ge device showed efficiencies of 4.95% and 5.85% under WLED and FL-4000K at 1200 lux, respectively. The prototype device also demonstrated successful test results under indoor conditions. These achievements are attributed to the enhanced carrier density, reduced density of defects, and low carrier recombinations.
- 26 October 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (44) , 23831-23842
Overcoming the limitations of low-bandgap Cu2ZnSn(S,Se)4devices under indoor light conditions: from design to prototype IoT application
With the growing need for cost-effective and sustainable Internet of things (IoT) technologies, kesterite-based solar cells are gaining popularity. We report the fabrication of an efficient CZTSSe absorber layer with improved Voc loss and its possible use in indoor photovoltaic applications. The double cation incorporation (co-doping) approach is employed with Ag and Ge to achieve this. The devices fabricated and tested under standard illumination (1 sun) and low light intensity conditions showed enhanced device performances and lower Voc losses after co-doping. Under indoor light conditions, Voc of 290 mV with white LED (WLED) and 310 mV with fluorescent lamp (FL-4000K) was achieved at the lowest intensity of 400 lux, while a value exceeding 350 mV was obtained at 1200 lux with FL-4000K for the CZTSSe:Ag–Ge device. Voc recoveries of >60% under all intensity conditions and >70% at 1200 lux with both WLED and FL-4000K were achieved. Moreover, the CZTSSe:Ag–Ge device showed efficiencies of 4.95% and 5.85% under WLED and FL-4000K at 1200 lux, respectively. The prototype device also demonstrated successful test results under indoor conditions. These achievements are attributed to the enhanced carrier density, reduced density of defects, and low carrier recombinations.
- 11 March 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (15) , 8466-8478
Understanding defects and band tailing characteristics and their impact on the device performance of Cu 2 ZnSn(S,Se) 4 solar cells
The Raman analysis of Cu 2 ZnSn(S,Se) 4 thin films revealed a change in the relative defect concentration and device performance with composition.
- 11 March 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (15) , 8466-8478
Understanding defects and band tailing characteristics and their impact on the device performance of Cu 2 ZnSn(S,Se) 4 solar cells
The Raman analysis of Cu 2 ZnSn(S,Se) 4 thin films revealed a change in the relative defect concentration and device performance with composition.