Jarosław Czaban
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jarosław Czaban has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dariusz Szpica
Faculty of Mechanical Engineering, Bialystok University of Technology, 45A Wiejska Str., 15-351 Bialystok, Poland
6 shared publications - Zbigniew Kamiński
Faculty of Mechanical Engineering , Bialystok University of Technology , ul. Wiejska 45C , Białystok , Poland
4 shared publications - Marcin Kisiel
Doctoral School, Bialystok University of Technology, 45A Wiejska Str., 15-351 Bialystok, Poland
2 shared publications Emil Weresa
Faculty of Mechanical Engineering, Department of Mechanical Engineering, Bialystok University of Technology, ul. Wiejska 45C, 15-351 Bialystok, Poland
1 shared publication- Piotr Banaszuk
Faculty of Civil Engineering and Environmental Sciences, Bialystok University of Technology, Bialystok, Poland
1 shared publication
Latest Publications
- Open Access
- 1 May 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Advances in Science and Technology Research Journal
- Vol. 20 (5) , 18-32
Road-testing of agricultural vehicles braking performance
According to Delegated Regulation (EU) 2015/68, the braking performance of agricultural vehicles is determined through road tests. Trailer braking performance is evaluated based on either the braking of the entire combination with coupling force measurement or the trailer's individual braking. In...
- 1 May 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Advances in Science and Technology Research Journal
- Vol. 20 (5) , 18-32
Open AccessRoad-testing of agricultural vehicles braking performance
According to Delegated Regulation (EU) 2015/68, the braking performance of agricultural vehicles is determined through road tests. Trailer braking performance is evaluated based on either the braking of the entire combination with coupling force measurement or the trailer's individual braking. In...
- Open Access
Stationary Type-Approval Test of the Tractor Pneumatic Braking System for Towed Vehicle Control
Agricultural tractors are equipped with air braking systems to supply and control the braking systems of towed vehicles. This system’s functional and operational characteristics significantly impact the compatibility and speed of the braking system of the tractor–trailer combination and are therefore checked during approval tests. This paper presents a test methodology and a description of the instrumentation and apparatus used to test the air braking systems of tractors under stationary conditions, as required by EU Regulation 2015/68. Sample test results of the trailer air supply system are included, such as checking the system for leaks, checking the pressure at the coupling heads, checking the compressor flow rate and air reservoir capacity, and checking the response time of the tractor control line. Approval authorities and tractor manufacturers can use the work results for quality control or product qualification tests.
Open AccessStationary Type-Approval Test of the Tractor Pneumatic Braking System for Towed Vehicle Control
Agricultural tractors are equipped with air braking systems to supply and control the braking systems of towed vehicles. This system’s functional and operational characteristics significantly impact the compatibility and speed of the braking system of the tractor–trailer combination and are therefore checked during approval tests. This paper presents a test methodology and a description of the instrumentation and apparatus used to test the air braking systems of tractors under stationary conditions, as required by EU Regulation 2015/68. Sample test results of the trailer air supply system are included, such as checking the system for leaks, checking the pressure at the coupling heads, checking the compressor flow rate and air reservoir capacity, and checking the response time of the tractor control line. Approval authorities and tractor manufacturers can use the work results for quality control or product qualification tests.
- Open Access
- 1 March 2025
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 19 (1) , 54-60
Type-Approval and Qualification Testing of Air Braking Systems of Agricultural Trailers Under Stationary Conditions
For road safety reasons, agricultural vehicle braking systems must comply with the approval requirements of EU Delegated Regulation 2015/68, which are evaluated during stationary and road testing conditions. For the stationary tests, an algorithm and procedures are developed to test the air braking systems of towed vehicles, including checking for tightness, pushrod strokes of brake chambers (adjustment), response times and the capacity of the compressed air reservoirs. Testing of a single-axle trailer braking system was carried out using a computer-controlled diagnostic device incorporating a simulator of the tractor’s braking system developed by the authors. The trailer test results obtained confirmed the usefulness of the methodology developed and showed high accuracy and repeatability of measurements. The results of this work can be used not only by type-approval bodies, but also by manufacturers of trailers and towed agricultural machinery for quality control or product qualification tests.
- 1 March 2025
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 19 (1) , 54-60
Open AccessType-Approval and Qualification Testing of Air Braking Systems of Agricultural Trailers Under Stationary Conditions
For road safety reasons, agricultural vehicle braking systems must comply with the approval requirements of EU Delegated Regulation 2015/68, which are evaluated during stationary and road testing conditions. For the stationary tests, an algorithm and procedures are developed to test the air braking systems of towed vehicles, including checking for tightness, pushrod strokes of brake chambers (adjustment), response times and the capacity of the compressed air reservoirs. Testing of a single-axle trailer braking system was carried out using a computer-controlled diagnostic device incorporating a simulator of the tractor’s braking system developed by the authors. The trailer test results obtained confirmed the usefulness of the methodology developed and showed high accuracy and repeatability of measurements. The results of this work can be used not only by type-approval bodies, but also by manufacturers of trailers and towed agricultural machinery for quality control or product qualification tests.
- Open Access
- 14 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11690
Numerical and Experimental Determination of the Bore Throughput Controlling the Operation of the Differential Section of a Pneumatic Brake Valve
Purpose: To assess the applicability of computational fluid dynamics (CFDs) in determining the flow parameters of inter-chamber nozzle openings in the differential section of a trailer air brake valve. Methodology: Numerical calculations were performed using SolidWorks Flow Simulation (SW-FS) and Ansys Fluent (A-F) with defined boundaries and initial conditions. The results were validated experimentally using the reservoir method and the lumped method for throughput identification. Results: CFD calculations determined the functional dependence of the mass flow rate on the nozzle diameter for a range of control nozzle bore diameters. The SW-FS 2024 and A-F 2023 software showed a mean difference of 4.66% in the total characteristics. The experimental validation resulted in differences of 6.31% (SW-FS) and 5.79% (A-F) compared to the CFD results. Theoretical contribution: This study fills a research gap in applying CFDs to brake valve performance analyses, providing a foundation for developing more complex numerical models to evaluate individual valve sections. Practical implications: The findings suggest that CFDs can be used to accurately determine the flow parameters of control nozzle orifices, with an average of a 6.05% difference from experimental tests. This approach can potentially streamline the design and optimization process for pneumatic brake valves.
- 14 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11690
Open AccessNumerical and Experimental Determination of the Bore Throughput Controlling the Operation of the Differential Section of a Pneumatic Brake Valve
Purpose: To assess the applicability of computational fluid dynamics (CFDs) in determining the flow parameters of inter-chamber nozzle openings in the differential section of a trailer air brake valve. Methodology: Numerical calculations were performed using SolidWorks Flow Simulation (SW-FS) and Ansys Fluent (A-F) with defined boundaries and initial conditions. The results were validated experimentally using the reservoir method and the lumped method for throughput identification. Results: CFD calculations determined the functional dependence of the mass flow rate on the nozzle diameter for a range of control nozzle bore diameters. The SW-FS 2024 and A-F 2023 software showed a mean difference of 4.66% in the total characteristics. The experimental validation resulted in differences of 6.31% (SW-FS) and 5.79% (A-F) compared to the CFD results. Theoretical contribution: This study fills a research gap in applying CFDs to brake valve performance analyses, providing a foundation for developing more complex numerical models to evaluate individual valve sections. Practical implications: The findings suggest that CFDs can be used to accurately determine the flow parameters of control nozzle orifices, with an average of a 6.05% difference from experimental tests. This approach can potentially streamline the design and optimization process for pneumatic brake valves.
- Open Access
- 1 July 2022
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 16 (3) , 233-241
Simulation Evaluation of the Influence of Selected Geometric Parameters on the Operation of the Pneumatic Braking System of a Trailer with a Differential Valve
This article presents simulation models of trailer air brake systems in configurations without a valve and with a differential valve, thus demonstrating the rationale for using a valve to improve system performance. Simplified mathematical models using the lumped method for systems without and with a differential valve are presented. The proposed valve can have two states of operation depending on the configuration of relevant parameters. These parameters can include the length of the control pipe, the throughput between chambers in the control part of the valve and the forcing rise time. Based on the calculations, it was found that the differential valve with large control pipe lengths can reduce the response time of the actuator by 42.77% relative to the system without the valve. In the case of transition of the valve to the tracking action, this time increases only by 9.93%. A force rise time of 0.5 s causes the transition of the valve from the accelerating action to the tracking action, with 9.23% delay relative to the system without a valve. The calculations can be used in the preliminary assessment of the speed of operation of pneumatic braking systems and in the formulation of guidelines for the construction of a prototypical differential valve. In conclusion, it is suggested to use a mechatronic system enabling smooth adjustment of the flow rate between chambers of the control system of the differential valve.
- 1 July 2022
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 16 (3) , 233-241
Open AccessSimulation Evaluation of the Influence of Selected Geometric Parameters on the Operation of the Pneumatic Braking System of a Trailer with a Differential Valve
This article presents simulation models of trailer air brake systems in configurations without a valve and with a differential valve, thus demonstrating the rationale for using a valve to improve system performance. Simplified mathematical models using the lumped method for systems without and with a differential valve are presented. The proposed valve can have two states of operation depending on the configuration of relevant parameters. These parameters can include the length of the control pipe, the throughput between chambers in the control part of the valve and the forcing rise time. Based on the calculations, it was found that the differential valve with large control pipe lengths can reduce the response time of the actuator by 42.77% relative to the system without the valve. In the case of transition of the valve to the tracking action, this time increases only by 9.93%. A force rise time of 0.5 s causes the transition of the valve from the accelerating action to the tracking action, with 9.23% delay relative to the system without a valve. The calculations can be used in the preliminary assessment of the speed of operation of pneumatic braking systems and in the formulation of guidelines for the construction of a prototypical differential valve. In conclusion, it is suggested to use a mechatronic system enabling smooth adjustment of the flow rate between chambers of the control system of the differential valve.
- 1 September 2017
- Published by Springer Nature in Materials Science
- Vol. 53 (2) , 226-234
Identification of the Mechanical Properties of Compound Feeds for Modeling the Processes of Thickening and Compaction
- 1 September 2017
- Published by Springer Nature in Materials Science
- Vol. 53 (2) , 226-234
Identification of the Mechanical Properties of Compound Feeds for Modeling the Processes of Thickening and Compaction
- Open Access
- 1 March 2015
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 9 (1) , 14-18
The Diesel and the Vegetable oil Properties Assessment in terms of Pumping Capability and Cooperation with Internal Combustion Engine Fuelling System
In the paper, the results of preliminary diesel and vegetable oil research were shown, the subject of which were directly intended to be the fuel for powering compression ignition engines. In the times of climate protection and more strict standards concerning combustion gas emissions, the fuel production and transportation process became an important aspect. Decentralization of this process and enabling fuel obtaining directly from cultivation (oleaginous plants) let limit the global CO2 emission. This is why the preliminary assessment of two fuel sorts properties was attempted, on one side, the basic one, which is the diesel, on the other side - vegetable oil. Prior to subjecting the compression ignition engine to the process of adaptation to vegetable fuelling, the properties of the fuel responsible for pumping should be assessed (mainly viscosity) and friction nodes cooperation (lubricity). The first of researched parameters is the base to elaborating the system of engine controlling algorithm or the range of changes in construction of powering system. The second one is the wear issue - object fitness and repairing overhauls.
- 1 March 2015
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 9 (1) , 14-18
Open AccessThe Diesel and the Vegetable oil Properties Assessment in terms of Pumping Capability and Cooperation with Internal Combustion Engine Fuelling System
In the paper, the results of preliminary diesel and vegetable oil research were shown, the subject of which were directly intended to be the fuel for powering compression ignition engines. In the times of climate protection and more strict standards concerning combustion gas emissions, the fuel production and transportation process became an important aspect. Decentralization of this process and enabling fuel obtaining directly from cultivation (oleaginous plants) let limit the global CO2 emission. This is why the preliminary assessment of two fuel sorts properties was attempted, on one side, the basic one, which is the diesel, on the other side - vegetable oil. Prior to subjecting the compression ignition engine to the process of adaptation to vegetable fuelling, the properties of the fuel responsible for pumping should be assessed (mainly viscosity) and friction nodes cooperation (lubricity). The first of researched parameters is the base to elaborating the system of engine controlling algorithm or the range of changes in construction of powering system. The second one is the wear issue - object fitness and repairing overhauls.
- Open Access
- 30 October 2014
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 20 (5) , 480-488
Operational assessment of selected gasoline and LPG vapour injector dosage regularity
The paper analyzes the problem of injector dosage irregularity in classical and alternative fueling systems in motor vehicles. An adoption of a newly manufactured subassembly as a starting point for the research creates idealized engine operating conditions (new engines). The question of investigating used subassemblies is rather difficult but it provides a better and clearer picture of the existing situation - the exhaust emissions. The authors have undertaken the problem of fueling irregularity as a response to a growing number of vehicles with malfunctions of LPG fueling systems that are currently very popular in Poland. In the course of the analysis, several injectors were tested to present the differences in their dosage irregularity. To realize the research tasks, different test stands with software were designed. To fully visualize the problem, several sets of injecting units were selected at different stages of their wear. The results have shown that gasoline injectors are characterized by approx 0.5% irregularity and if heavily worn - 6%. LPG vapour injectors reached the level of 5% and heavily worn ones - 50%. DOI: http://dx.doi.org/10.5755/j01.mech.20.5.7780
- 30 October 2014
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 20 (5) , 480-488
Open AccessOperational assessment of selected gasoline and LPG vapour injector dosage regularity
The paper analyzes the problem of injector dosage irregularity in classical and alternative fueling systems in motor vehicles. An adoption of a newly manufactured subassembly as a starting point for the research creates idealized engine operating conditions (new engines). The question of investigating used subassemblies is rather difficult but it provides a better and clearer picture of the existing situation - the exhaust emissions. The authors have undertaken the problem of fueling irregularity as a response to a growing number of vehicles with malfunctions of LPG fueling systems that are currently very popular in Poland. In the course of the analysis, several injectors were tested to present the differences in their dosage irregularity. To realize the research tasks, different test stands with software were designed. To fully visualize the problem, several sets of injecting units were selected at different stages of their wear. The results have shown that gasoline injectors are characterized by approx 0.5% irregularity and if heavily worn - 6%. LPG vapour injectors reached the level of 5% and heavily worn ones - 50%. DOI: http://dx.doi.org/10.5755/j01.mech.20.5.7780
- Open Access
- 1 September 2014
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 8 (3) , 151-155
The Diagnostic System of A – 604 Automatic Transmission
Automatic gearbox gains increasing popularity in Europe. Little interest in diagnosis of such type of transmission in Poland results from the fact of small share in the whole market of operated cars, so there is a lack of availability of special diagnostic devices. These factors cause issues of expensive repairs, often involving a replacement of subassembly to new or aftermarket one. To a small extent some prophylactic diagnostic tests are conducted, which can eliminate future gearbox system failures. In the paper, the proposition of diagnostic system of popular A - 604 gearbox was presented. The authors are seeking for the possibility of using such type of devices to functional elaboration of gearboxes after renovation. The built system pursues the drive of the researched object, connected with simulated load, where special controller, replacing the original one, is responsible for controlling gearbox operation. This way is used to evaluate the mechanic and hydraulic parts' state. Analysis of signal runs, registered during measurements lets conclude about operation correctness, where as comparison with stock data verifies the technical state of an automatic gearbox.
- 1 September 2014
- Published by Bialystok University of Technology in Acta Mechanica et Automatica
- Vol. 8 (3) , 151-155
Open AccessThe Diagnostic System of A – 604 Automatic Transmission
Automatic gearbox gains increasing popularity in Europe. Little interest in diagnosis of such type of transmission in Poland results from the fact of small share in the whole market of operated cars, so there is a lack of availability of special diagnostic devices. These factors cause issues of expensive repairs, often involving a replacement of subassembly to new or aftermarket one. To a small extent some prophylactic diagnostic tests are conducted, which can eliminate future gearbox system failures. In the paper, the proposition of diagnostic system of popular A - 604 gearbox was presented. The authors are seeking for the possibility of using such type of devices to functional elaboration of gearboxes after renovation. The built system pursues the drive of the researched object, connected with simulated load, where special controller, replacing the original one, is responsible for controlling gearbox operation. This way is used to evaluate the mechanic and hydraulic parts' state. Analysis of signal runs, registered during measurements lets conclude about operation correctness, where as comparison with stock data verifies the technical state of an automatic gearbox.
- 28 October 2013
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 19 (5) , 600-605
DRIVE TEST SYSTEM TO BE USED ON ROLLER DYNAMOMETER
DRIVE TEST SYSTEM TO BE USED ON ROLLER DYNAMOMETER
- 28 October 2013
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 19 (5) , 600-605
DRIVE TEST SYSTEM TO BE USED ON ROLLER DYNAMOMETER
DRIVE TEST SYSTEM TO BE USED ON ROLLER DYNAMOMETER