Yan-Bo Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yan-Bo Wang has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
Guo-Qiang Li
Professor, College of Civil Engineering, Tongji Univ., Shanghai 200092, China; Professor, State Key Laboratory for Disaster Reduction in Civil Engineering, Tongji Univ., Shanghai 200092, China
27 shared publicationsFei-Fei Sun
7 shared publicationsSu-Wen Chen
7 shared publicationsJ.Y. Richard Liew
5 shared publicationsLe-Tian Hai
College of Civil Engineering, Tongji University, 200092 Shanghai, China
4 shared publicationsTian-Ji Li
3 shared publications
Latest Publications
- 1 July 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 152 (7)
Fire Resistance of Concrete-Filled High-Strength Fire-Resistant Steel Tubular Columns
- 1 July 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 152 (7)
Fire Resistance of Concrete-Filled High-Strength Fire-Resistant Steel Tubular Columns
- 20 March 2025
- Published by Elsevier in Engineering Structures
- Vol. 333
Influence of slenderness on confining effect of axially loaded circular CFST columns with high-strength materials
- 20 March 2025
- Published by Elsevier in Engineering Structures
- Vol. 333
Influence of slenderness on confining effect of axially loaded circular CFST columns with high-strength materials
- Top Cited Papers
- 11 March 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 471
Investigation on the mechanical properties of heat-affected zone of butt-welded joint of Q690 and Q960 steel based on physical thermal simulation
- 11 March 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 471
Top Cited PapersInvestigation on the mechanical properties of heat-affected zone of butt-welded joint of Q690 and Q960 steel based on physical thermal simulation
- 25 October 2023
- Published by Elsevier in Engineering Structures
- Vol. 298
An improved constitutive model for steel tube-confined ultra-high-strength concrete
- 25 October 2023
- Published by Elsevier in Engineering Structures
- Vol. 298
An improved constitutive model for steel tube-confined ultra-high-strength concrete
- 8 June 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 76
Seismic behavior of steel beam-column connection with assembled steel rod energy dissipaters
- 8 June 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 76
Seismic behavior of steel beam-column connection with assembled steel rod energy dissipaters
- 24 October 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 182
Local buckling and hysteretic behavior of Q690 high-strength steel box-section beam–columns
- 24 October 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 182
Local buckling and hysteretic behavior of Q690 high-strength steel box-section beam–columns
- 17 January 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 172
Buckling analysis and experimental study of simply-supported single-corrugation steel plates subjected to compression
- 17 January 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 172
Buckling analysis and experimental study of simply-supported single-corrugation steel plates subjected to compression
- 12 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 207-212
Optimal design model for wind resistance based on static numerical simulation of large span bridges and its application
For bridges, especially large span bridges, wind load variations have a large impact on the bridge and therefore wind resistance is an important factor in evaluating the bridge design. Given that bridge wind resistance design mostly relies on wind tunnel tests, the cost is high. In this paper, a more complete bridge wind resistance design system is proposed, based on numerical simulation optimization, which is cost effective and efficient. The wind loads are obtained by applying the established generic wind load calculation model through extreme value analysis of available wind speed data, finding wind speed distribution maps and calculating several design reference wind speeds using road bridge wind gauges. Based on the bridge cross-section geometry and material properties, a basic finite element analysis model is developed to solve the static three-part force, and finally the bridge static and vibration analysis is obtained. This paper takes the Qinglan Bridge in Hainan Province, China, as an example, and uses the wind resistance design model proposed in this paper to find the final design reference wind speed of 32.3906m/s. The horizontal wind loads of the bridge are found to be 1032.5Pa and 1349.5Pa using the general formula and the wind gauge for highway bridges respectively, indicating that the ratio of the horizontal loads found by the two formulas is 0.765 under the same conditions. The bridge foundation finite element model was used to find the three dimensional static component forces and to obtain the maximum positive stress of 89.23Mpa in the bridge main girder, which occurred at the bridge span of 798.2m. Finally, the response was found in the form of a power spectral density function using the previously inputted data on the bridge characteristics and turbulence data from the Qinglan Bridge to return the fundamental frequency for different cases.
- 12 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 207-212
Optimal design model for wind resistance based on static numerical simulation of large span bridges and its application
For bridges, especially large span bridges, wind load variations have a large impact on the bridge and therefore wind resistance is an important factor in evaluating the bridge design. Given that bridge wind resistance design mostly relies on wind tunnel tests, the cost is high. In this paper, a more complete bridge wind resistance design system is proposed, based on numerical simulation optimization, which is cost effective and efficient. The wind loads are obtained by applying the established generic wind load calculation model through extreme value analysis of available wind speed data, finding wind speed distribution maps and calculating several design reference wind speeds using road bridge wind gauges. Based on the bridge cross-section geometry and material properties, a basic finite element analysis model is developed to solve the static three-part force, and finally the bridge static and vibration analysis is obtained. This paper takes the Qinglan Bridge in Hainan Province, China, as an example, and uses the wind resistance design model proposed in this paper to find the final design reference wind speed of 32.3906m/s. The horizontal wind loads of the bridge are found to be 1032.5Pa and 1349.5Pa using the general formula and the wind gauge for highway bridges respectively, indicating that the ratio of the horizontal loads found by the two formulas is 0.765 under the same conditions. The bridge foundation finite element model was used to find the three dimensional static component forces and to obtain the maximum positive stress of 89.23Mpa in the bridge main girder, which occurred at the bridge span of 798.2m. Finally, the response was found in the form of a power spectral density function using the previously inputted data on the bridge characteristics and turbulence data from the Qinglan Bridge to return the fundamental frequency for different cases.
- Open Access
- 19 August 2021
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 8
Editorial: Composite Use of High Strength Steel and Concrete Materials for Sustainable Civil Engineering
Editorial: Composite Use of High Strength Steel and Concrete Materials for Sustainable Civil Engineering
- 19 August 2021
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 8
Open AccessEditorial: Composite Use of High Strength Steel and Concrete Materials for Sustainable Civil Engineering
Editorial: Composite Use of High Strength Steel and Concrete Materials for Sustainable Civil Engineering