Zbigniew Jakielaszek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zbigniew Jakielaszek has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Mirosław Nowakowski
Air Force Institute of Technology, Ksiecia Boleslawa St. 6, 01-494 Warsaw, Poland
4 shared publications - Andrzej Jaroslaw Panas
Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, 00-908 Warsaw, Poland
3 shared publications - Bartosz Fikus
Jarosław Dąbrowski Military University of Technology, Warsaw 46, Poland
1 shared publication - Grzegorz Kowaleczko
Air Force Institute of Technology, Warsaw, Poland
1 shared publication - Jarosław Krzonkalla
Air Force Institute of Technology
1 shared publication - Jedrzej Drozdowicz
Institute of Electronic Systems, Warsaw University of Technology, Warsaw, Poland
1 shared publication
Latest Publications
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 484-488
Miniaturized Flight Data Recorder for Unmanned Aerial Vehicles and Ultralight Aircrafts
Flight data recorder is a device that records various flight parameters and is able to survive the crash for increasing aviation safety. Aircrafts which can have an impact on the safety of flights in the airspace are becoming smaller and more accessible. Good examples are unmanned aerial vehicles or ultralight aircrafts. It would be appropriate to equip these objects with flight data recorders in order to ensure that every crash will be accompanied to improvement of the aviation safety. While the legitimacy of FDR (flight data recorder) installation into manned objects is pretty obvious, for a UAV (unmanned aerial vehicle) it is not so clear. There are some cases that the UAV has dropped and damaged some facilities or even dropped on human, additionally loss of often very expensive object should occur as rarely as possible. In both cases, the lifting capacity is very limited so there is requirement to significantly reduce the weight of the recording device. Minimum dimensions and weight are strongly dependent on the assumed conditions of the accident and on the size of the aircraft. The paper describes design of the electronics module, partial concepts of the whole flight data recorder and the first crash survival tests.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 484-488
Miniaturized Flight Data Recorder for Unmanned Aerial Vehicles and Ultralight Aircrafts
Flight data recorder is a device that records various flight parameters and is able to survive the crash for increasing aviation safety. Aircrafts which can have an impact on the safety of flights in the airspace are becoming smaller and more accessible. Good examples are unmanned aerial vehicles or ultralight aircrafts. It would be appropriate to equip these objects with flight data recorders in order to ensure that every crash will be accompanied to improvement of the aviation safety. While the legitimacy of FDR (flight data recorder) installation into manned objects is pretty obvious, for a UAV (unmanned aerial vehicle) it is not so clear. There are some cases that the UAV has dropped and damaged some facilities or even dropped on human, additionally loss of often very expensive object should occur as rarely as possible. In both cases, the lifting capacity is very limited so there is requirement to significantly reduce the weight of the recording device. Minimum dimensions and weight are strongly dependent on the assumed conditions of the accident and on the size of the aircraft. The paper describes design of the electronics module, partial concepts of the whole flight data recorder and the first crash survival tests.
- Open Access
- 1 October 2017
- Published by Walter de Gruyter GmbH in Journal of Konbin
- Vol. 43 (1) , 179-222
Testing the Catastrophic Recorder Resistance Against the Impact of Catastrophic Factors
The subject of the research was a catastrophic recorder of the S2-3a system for recording flight parameters, developed at the Air Force Institute of Technology. The article discusses tests of catastrophic recorders’ resilience to factors present at aircraft accidents. The document specifying the requirements for catastrophic recorders of flight parameters includes the defence standard: NO-16-A200, and the European standard: EuroCAE ED-112. According to NO-16-A200 and ED-112 standards, the protective unit should be resistant to: g-forces existing during crash, puncture, compression, fire, underwater pressure and aggressive liquids.
- 1 October 2017
- Published by Walter de Gruyter GmbH in Journal of Konbin
- Vol. 43 (1) , 179-222
Open AccessTesting the Catastrophic Recorder Resistance Against the Impact of Catastrophic Factors
The subject of the research was a catastrophic recorder of the S2-3a system for recording flight parameters, developed at the Air Force Institute of Technology. The article discusses tests of catastrophic recorders’ resilience to factors present at aircraft accidents. The document specifying the requirements for catastrophic recorders of flight parameters includes the defence standard: NO-16-A200, and the European standard: EuroCAE ED-112. According to NO-16-A200 and ED-112 standards, the protective unit should be resistant to: g-forces existing during crash, puncture, compression, fire, underwater pressure and aggressive liquids.
- Open Access
- 2 February 2017
- Published by Taylor & Francis in Journal of Marine Engineering & Technology
- Vol. 16 (4) , 319-325
Evaluation of numerical modelling application for the crash test planning of the catastrophic Flight Data Recorder
Catastrophic Flight Data Recorders (FDRs), the so-called black boxes, belong to the on-board equipment, the task of which is not only to operate properly while recording selected parameters under all flight conditions but also to protect the recorded data against the loss in the aircraft crash conditions. The requirements related to catastrophic resistance of FDRs are defined in the European standard EuroCAE ED-112 and the Polish standard NO-16-A200:2015. One of the requirements includes the catastrophic recorder’s resistance to the acceleration overload of 3400 g. The compliance with the standard is checked during crash tests. In this paper, a procedure of planning and carrying out the mentioned tests for S2-3a-K protected unit of S2-3a catastrophic FDR manufactured by the Air Force Institute of Technology was described. It is an iterative procedure involving consecutive experimental tests and both analytical and numerical calculations. The experimental tests were performed using a DPZ-250 pneumatic gun. The testing probe was shot at the target of sand deposits of modified geometry and mass characteristics. Effectiveness of the developed procedure was shown by comparing the experimental results, namely recordings of the probe deceleration captured with a fast camera, with results of numerical simulation of the probe terminal ballistic.
- 2 February 2017
- Published by Taylor & Francis in Journal of Marine Engineering & Technology
- Vol. 16 (4) , 319-325
Open AccessEvaluation of numerical modelling application for the crash test planning of the catastrophic Flight Data Recorder
Catastrophic Flight Data Recorders (FDRs), the so-called black boxes, belong to the on-board equipment, the task of which is not only to operate properly while recording selected parameters under all flight conditions but also to protect the recorded data against the loss in the aircraft crash conditions. The requirements related to catastrophic resistance of FDRs are defined in the European standard EuroCAE ED-112 and the Polish standard NO-16-A200:2015. One of the requirements includes the catastrophic recorder’s resistance to the acceleration overload of 3400 g. The compliance with the standard is checked during crash tests. In this paper, a procedure of planning and carrying out the mentioned tests for S2-3a-K protected unit of S2-3a catastrophic FDR manufactured by the Air Force Institute of Technology was described. It is an iterative procedure involving consecutive experimental tests and both analytical and numerical calculations. The experimental tests were performed using a DPZ-250 pneumatic gun. The testing probe was shot at the target of sand deposits of modified geometry and mass characteristics. Effectiveness of the developed procedure was shown by comparing the experimental results, namely recordings of the probe deceleration captured with a fast camera, with results of numerical simulation of the probe terminal ballistic.
- Top Cited Papers
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
35 GHz FMCW drone detection system
This paper presents an experimental system dedicated for the detection and tracking of small aerial targets such as Unmanned Aerial Vehicles (UAVs) in particular small drones (multirotors). The system was proposed in response to increasing drone popularity and the related threats. The hardware and software parts of the system are covered, including the analogue front-end, FPGA based pre-processing and PC based processing, detection and tracking. Real life trials are described with promising results provided. Further research on the subject is proposed.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Top Cited Papers35 GHz FMCW drone detection system
This paper presents an experimental system dedicated for the detection and tracking of small aerial targets such as Unmanned Aerial Vehicles (UAVs) in particular small drones (multirotors). The system was proposed in response to increasing drone popularity and the related threats. The hardware and software parts of the system are covered, including the analogue front-end, FPGA based pre-processing and PC based processing, detection and tracking. Real life trials are described with promising results provided. Further research on the subject is proposed.
- Open Access
- 1 September 2015
- Published by Walter de Gruyter GmbH in Journal of Konbin
- Vol. 33 (1) , 135-150
A System to Measure Service Loads that Affect the SU-22UM3k Structure / System Do Pomiaru Obciążeń Eksploatacyjnych w Elementach Struktury Samolotu SU-22UM3k
Instytut Techniczny Wojsk Lotniczych has for years been engaged in research and development (R&D) aimed at the determination of wear-and-tear level that particular aircraft suffer from. The paper has been intended to present an innovative measuring-and-recording system to collect information on service loads that arise in structural components of the Su-22UM3K aircraft. Research work into loads in some selected structural components of the Su-22UM3K has been carried out with the KAM-500 measuring system applied. Modular design has been used to develop the system. This, in turn, allows of changes in the system’s configuration, according to what a measuring task requires. The flight testing of loads has covered items of tasks included in the flying training program for the Su- 22UM3K to collect/deliver data on an actual service profile and to determine representative strain-gauge measuring channels to be utilized in further aircraft’s service.
- 1 September 2015
- Published by Walter de Gruyter GmbH in Journal of Konbin
- Vol. 33 (1) , 135-150
Open AccessA System to Measure Service Loads that Affect the SU-22UM3k Structure / System Do Pomiaru Obciążeń Eksploatacyjnych w Elementach Struktury Samolotu SU-22UM3k
Instytut Techniczny Wojsk Lotniczych has for years been engaged in research and development (R&D) aimed at the determination of wear-and-tear level that particular aircraft suffer from. The paper has been intended to present an innovative measuring-and-recording system to collect information on service loads that arise in structural components of the Su-22UM3K aircraft. Research work into loads in some selected structural components of the Su-22UM3K has been carried out with the KAM-500 measuring system applied. Modular design has been used to develop the system. This, in turn, allows of changes in the system’s configuration, according to what a measuring task requires. The flight testing of loads has covered items of tasks included in the flying training program for the Su- 22UM3K to collect/deliver data on an actual service profile and to determine representative strain-gauge measuring channels to be utilized in further aircraft’s service.
- Open Access
- 1 December 2014
- Published by Walter de Gruyter GmbH in Journal of Konbin
- Vol. 30 (1) , 31-46
A Method For Determination And Standardization Of Performance Parameters For Aircrafts With Electric Drives
The study outlines the technique for flight tests carried out for a plane powered by an electric drive and the method for standardization of performance parameters applicable to evaluation of test results. Due to the relatively new type of drive, which is an electric motor, the literature references provide no descriptions of such issues. Therefore the solutions presented in the paper are the own contribution of the research team from Air Force Institute of Technology (ITWL).
- 1 December 2014
- Published by Walter de Gruyter GmbH in Journal of Konbin
- Vol. 30 (1) , 31-46
Open AccessA Method For Determination And Standardization Of Performance Parameters For Aircrafts With Electric Drives
The study outlines the technique for flight tests carried out for a plane powered by an electric drive and the method for standardization of performance parameters applicable to evaluation of test results. Due to the relatively new type of drive, which is an electric motor, the literature references provide no descriptions of such issues. Therefore the solutions presented in the paper are the own contribution of the research team from Air Force Institute of Technology (ITWL).
- 1 January 2014
- Published by Index Copernicus in Journal of KONES. Powertrain and Transport
- Vol. 21 (4) , 203-210
SELECTED CHARACTERISTICS OF THE ELECTRIC PROPULSION SYSTEM OF AIRCRAFT AS FOUND OUT FROM THE GROUND-BASED LABORATORY TESTS
- 1 January 2014
- Published by Index Copernicus in Journal of KONES. Powertrain and Transport
- Vol. 21 (4) , 203-210
SELECTED CHARACTERISTICS OF THE ELECTRIC PROPULSION SYSTEM OF AIRCRAFT AS FOUND OUT FROM THE GROUND-BASED LABORATORY TESTS