Gustavo Tontini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gustavo Tontini has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Guilherme Dalla Lana Semione
Deutsches Elektronen-Synchrotron DESY
6 shared publications V. Drago
5 shared publicationsValderes Drago
4 shared publicationsC. Binder
3 shared publications- Suelen Barg
Department of Materials, The University of Manchester, Manchester, M13 9PL, UNITED KINGDOM OF GREAT BRITAIN AND NORTHERN IRELAND
3 shared publications V.A.V. Schmachtenberg
3 shared publications
Latest Publications
- Open Access
- 23 February 2021
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (20) , 205601
Ice-templated hybrid graphene oxide—graphene nanoplatelet lamellar architectures: tuning mechanical and electrical properties
The traditional freeze-casting route for processing graphene-based aerogels is generally restricted to aqueously dispersed flakes of graphene oxide (GO) and post-processing reduction treatments, which brings restrictions to the aerogels electrical properties. In this work, we report a versatile aqueous processing route that uses the ability of GO todisperse graphene nanoplatelets (GNP) to produce rGO-GNP lamellar aerogels via unidirectional freeze-casting. In order to optimise the properties of the aerogel, GO-GNP dispersions were partially reduced by L-ascorbic acid prior to freeze-casting to tune the carbon and oxygen (C/O) ratio. The aerogels were then heat treated after casting to fully reduce the GO. The chemical reduction time was found to control the microstructure of the resulting aeorgels and thus to tune their electrical and mechanical properties. An rGO-GNP lamellar aerogel with density of 20.8 ± 0.8 mg cm−3 reducing using a reduction of 60 min achieved an electrical conductivity of 42.3 S m−1. On the other hand, an optimal reduction time of 35 min led to an aerogel with compressive modulus of 0.51 ±0.06 MPa at a density of 23.2 ± 0.7 mg cm−3, revealing a compromise between the tuning of electrical and mechanical properties. We show the present processing route can also be easily applied to produce lamellar aerogels on other graphene-based materials such as electrochemically exfoliated graphene.
- 23 February 2021
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (20) , 205601
Open AccessIce-templated hybrid graphene oxide—graphene nanoplatelet lamellar architectures: tuning mechanical and electrical properties
The traditional freeze-casting route for processing graphene-based aerogels is generally restricted to aqueously dispersed flakes of graphene oxide (GO) and post-processing reduction treatments, which brings restrictions to the aerogels electrical properties. In this work, we report a versatile aqueous processing route that uses the ability of GO todisperse graphene nanoplatelets (GNP) to produce rGO-GNP lamellar aerogels via unidirectional freeze-casting. In order to optimise the properties of the aerogel, GO-GNP dispersions were partially reduced by L-ascorbic acid prior to freeze-casting to tune the carbon and oxygen (C/O) ratio. The aerogels were then heat treated after casting to fully reduce the GO. The chemical reduction time was found to control the microstructure of the resulting aeorgels and thus to tune their electrical and mechanical properties. An rGO-GNP lamellar aerogel with density of 20.8 ± 0.8 mg cm−3 reducing using a reduction of 60 min achieved an electrical conductivity of 42.3 S m−1. On the other hand, an optimal reduction time of 35 min led to an aerogel with compressive modulus of 0.51 ±0.06 MPa at a density of 23.2 ± 0.7 mg cm−3, revealing a compromise between the tuning of electrical and mechanical properties. We show the present processing route can also be easily applied to produce lamellar aerogels on other graphene-based materials such as electrochemically exfoliated graphene.
- Open Access
- 13 July 2020
- Published by Wiley in Energy & Environmental Materials
- Vol. 3 (3) , 380-388
Freeze‐assisted Tape Casting of Vertically Aligned MXene Films for High Rate Performance Supercapacitors
Conventional electrode preparation techniques of supercapacitors such as tape casting or vacuum filtration often lead to the restacking or agglomeration of two‐dimensional (2D) materials. As a result, tortuous paths are created for the electrolyte ions and their adsorption onto the surfaces of the active materials can be prevented. Consequently, maintaining high rate performance while increasing the thickness of electrodes has been a challenge. Herein, a facile freeze‐assisted tape‐casting (FaTC) method is reported for the scalable fabrication of flexible MXene (Ti3C2Tx) supercapacitor electrode films of up to 700 μm thickness, exhibiting homogeneous ice‐template microstructure composed of vertically aligned MXene walls within lamellar pores. The efficient ion transport created by the internal morphology allows for fast electrochemical charge–discharge cycles and near thickness‐independent performance at up to 3000 mV s−1 for films of up to 300 μm in thickness. By increasing the scan rate from 20 to 10,000 mV s−1, Ti3C2Tx films of 150 μm in thickness sustain 50% of its specific capacitance (222.9 F g−1). When the film thickness is doubled to 300 μm, its capacitance is still retained by 60 % (at 213.3 F g−1) when the scan rate is increased from 20 to 3000 mV s−1, with a capacitance retention above 97.7% for over 14,000 cycles at 10 A g−1. They also showed a remarkably high gravimetric and areal power density of 150 kW kg−1 at 1000 A g−1 and 667 mW cm−2 at 4444 mA cm−2, respectively. FaTC has the potential to provide industry with a viable way to fabricate electrodes formed from 2D materials on a large scale, while providing promising performance for use in a wide range of applications, such as flexible electronics and wearable energy storage devices.
- 13 July 2020
- Published by Wiley in Energy & Environmental Materials
- Vol. 3 (3) , 380-388
Open AccessFreeze‐assisted Tape Casting of Vertically Aligned MXene Films for High Rate Performance Supercapacitors
Conventional electrode preparation techniques of supercapacitors such as tape casting or vacuum filtration often lead to the restacking or agglomeration of two‐dimensional (2D) materials. As a result, tortuous paths are created for the electrolyte ions and their adsorption onto the surfaces of the active materials can be prevented. Consequently, maintaining high rate performance while increasing the thickness of electrodes has been a challenge. Herein, a facile freeze‐assisted tape‐casting (FaTC) method is reported for the scalable fabrication of flexible MXene (Ti3C2Tx) supercapacitor electrode films of up to 700 μm thickness, exhibiting homogeneous ice‐template microstructure composed of vertically aligned MXene walls within lamellar pores. The efficient ion transport created by the internal morphology allows for fast electrochemical charge–discharge cycles and near thickness‐independent performance at up to 3000 mV s−1 for films of up to 300 μm in thickness. By increasing the scan rate from 20 to 10,000 mV s−1, Ti3C2Tx films of 150 μm in thickness sustain 50% of its specific capacitance (222.9 F g−1). When the film thickness is doubled to 300 μm, its capacitance is still retained by 60 % (at 213.3 F g−1) when the scan rate is increased from 20 to 3000 mV s−1, with a capacitance retention above 97.7% for over 14,000 cycles at 10 A g−1. They also showed a remarkably high gravimetric and areal power density of 150 kW kg−1 at 1000 A g−1 and 667 mW cm−2 at 4444 mA cm−2, respectively. FaTC has the potential to provide industry with a viable way to fabricate electrodes formed from 2D materials on a large scale, while providing promising performance for use in a wide range of applications, such as flexible electronics and wearable energy storage devices.
- Open Access
- 17 March 2020
- Published by IOP Publishing in Journal of Physics: Materials
- Vol. 3 (2) , 022001
MXene-based 3D porous macrostructures for electrochemical energy storage
- 17 March 2020
- Published by IOP Publishing in Journal of Physics: Materials
- Vol. 3 (2) , 022001
Open AccessMXene-based 3D porous macrostructures for electrochemical energy storage
- 1 December 2019
- Published by Elsevier in Ceramics International
- Vol. 45 (17) , 22344-22350
Structural and magnetic properties of Pd doped h-NiS nanoparticles prepared via seeding method
- 1 December 2019
- Published by Elsevier in Ceramics International
- Vol. 45 (17) , 22344-22350
Structural and magnetic properties of Pd doped h-NiS nanoparticles prepared via seeding method
- 1 October 2019
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 487
Study of soft magnetic composites of iron coated with nanoparticles dispersion in liquid glass
- 1 October 2019
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 487
Study of soft magnetic composites of iron coated with nanoparticles dispersion in liquid glass
- 1 November 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 768, 896-902
Nanostructured nickel sulfides synthesized by modified polyol method exhibiting blocking/freezing temperature
- 1 November 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 768, 896-902
Nanostructured nickel sulfides synthesized by modified polyol method exhibiting blocking/freezing temperature
- Open Access
- 1 January 2017
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 6 (1) , 33-39
Laser composite surfacing of A681 steel with WC+Cr+Co for improved wear resistance
- 1 January 2017
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 6 (1) , 33-39
Open AccessLaser composite surfacing of A681 steel with WC+Cr+Co for improved wear resistance
- 12 September 2016
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 68 (6) , 658-664
Synthesis of nanostructured flower-like MoS2 and its friction properties as additive in lubricating oils
Purpose: This paper aims to synthesize nanostructured flower-like molybdenum disulphide (MoS2) particles and evaluate their suitability to act as additives for lubricants. Design/methodology/approach: A hydrothermal method without any surfactant successfully produced 250 nm mean diameter Nanostructured flower-like MoS2 particles. The resulting product was then solvothermally treated with absolute ethanol producing lipophilic powder particles which after being dispersed in two different lubricants were tribologicaly characterized by using a pin-on-disk tribometer geometry with reciprocal movement under immersion. Findings: The influence on the stability and the coefficient of friction of the nano-oils is shown to be strongly dependent on their molecular structure. After 1 h of tribological testing, a ramified polyolester oil with 1 Wt.% of MoS2 nanoflowers did not show decrease in its average coefficient of friction, while an additive naphthenic oil with the same concentration of nanoparticles showed a decrease of 86 per cent. Originality/value: In this paper, nanostructured flower-like MoS2 synthesized by the hydrothermal method was dispersed in lubricating oils to study its stability and tribological properties. To ensure good stability of the nano-oils, the particles were solvothermally treated with absolute ethanol to dehydrate and lipophilize them. A ramified polyolester-based nano-oil with 1 Wt.% of MoS2 nanoflowers showed no decrease in its steady state coefficient of friction, while a naphthenic-based nano-oil with the same concentration of nanoparticles presented a remarkable 86 per cent reduction.
- 12 September 2016
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 68 (6) , 658-664
Synthesis of nanostructured flower-like MoS2 and its friction properties as additive in lubricating oils
Purpose: This paper aims to synthesize nanostructured flower-like molybdenum disulphide (MoS2) particles and evaluate their suitability to act as additives for lubricants. Design/methodology/approach: A hydrothermal method without any surfactant successfully produced 250 nm mean diameter Nanostructured flower-like MoS2 particles. The resulting product was then solvothermally treated with absolute ethanol producing lipophilic powder particles which after being dispersed in two different lubricants were tribologicaly characterized by using a pin-on-disk tribometer geometry with reciprocal movement under immersion. Findings: The influence on the stability and the coefficient of friction of the nano-oils is shown to be strongly dependent on their molecular structure. After 1 h of tribological testing, a ramified polyolester oil with 1 Wt.% of MoS2 nanoflowers did not show decrease in its average coefficient of friction, while an additive naphthenic oil with the same concentration of nanoparticles showed a decrease of 86 per cent. Originality/value: In this paper, nanostructured flower-like MoS2 synthesized by the hydrothermal method was dispersed in lubricating oils to study its stability and tribological properties. To ensure good stability of the nano-oils, the particles were solvothermally treated with absolute ethanol to dehydrate and lipophilize them. A ramified polyolester-based nano-oil with 1 Wt.% of MoS2 nanoflowers showed no decrease in its steady state coefficient of friction, while a naphthenic-based nano-oil with the same concentration of nanoparticles presented a remarkable 86 per cent reduction.
- 1 June 2016
- Published by Elsevier in Ceramics International
- Vol. 42 (8) , 10127-10131
Seed-induced synthesis of h-NiS single-crystalline hexagonal nanoparticles
- 1 June 2016
- Published by Elsevier in Ceramics International
- Vol. 42 (8) , 10127-10131
Seed-induced synthesis of h-NiS single-crystalline hexagonal nanoparticles