Michael Niaounakis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Michael Niaounakis has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Evagelia Kontou
Mechanics Department, School of Applied Mathematical and Physical Sciences, National Technical University of Athens, Athens, Greece
5 shared publications C.P. Halvadakis
Mytilene, January 2004
3 shared publicationsE. Kontou
3 shared publicationsPanayiotis Georgiopoulos
Department of Applied Mathematical and Physical Sciences Section of Mechanics National Technical University of Athens GR‐15773 Athens Greece
3 shared publicationsC. Christodoulides
National Technical University of Athens, Department of Physics, Zografou Campus, 15780 Athens, Greece
2 shared publicationsG. Spathis
Department of Theoretical and Applied Mechanics, National Technical University of Athens, 5 Heroes of Polytechniou Ave., 15773 Athens, Greece
2 shared publications
Latest Publications
- 6 November 2013
- Published by Wiley in Polymer Composites
- Vol. 35 (6) , 1140-1149
Thermomechanical properties and rheological behavior of biodegradable composites
The effect of type and content of fillers on the thermal, mechanical, and rheological behavior of the commercial biodegradable polyester product, Ecovio® (BASF) is analytically studied. Ecovio® is basically a blend of poly(butylene adipate‐terephthalate) (PBAT) copolyester (Ecoflex®, BASF) and polylactide (PLA). Two different types of fillers (nanosilica particles and micro‐sized wood‐flour), at various weight fractions were used for this purpose. The role of these fillers on the thermomechanical performance of Ecovio® was investigated in terms of several experimental techniques including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), creep, tensile testing, and single cantilever bending. The rheological behavior has been systematically analyzed, providing additional evidence about the dispersion quality and the interfacial effects between nanofillers and matrix. One of the findings of this work is that the presence of PBAT in the blend (PLA/PBAT) enhances the compatibility of the polymer matrix with both fillers and their dispersion quality. POLYM. COMPOS., 35:1140–1149, 2014. © 2013 Society of Plastics Engineers
- 6 November 2013
- Published by Wiley in Polymer Composites
- Vol. 35 (6) , 1140-1149
Thermomechanical properties and rheological behavior of biodegradable composites
The effect of type and content of fillers on the thermal, mechanical, and rheological behavior of the commercial biodegradable polyester product, Ecovio® (BASF) is analytically studied. Ecovio® is basically a blend of poly(butylene adipate‐terephthalate) (PBAT) copolyester (Ecoflex®, BASF) and polylactide (PLA). Two different types of fillers (nanosilica particles and micro‐sized wood‐flour), at various weight fractions were used for this purpose. The role of these fillers on the thermomechanical performance of Ecovio® was investigated in terms of several experimental techniques including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), creep, tensile testing, and single cantilever bending. The rheological behavior has been systematically analyzed, providing additional evidence about the dispersion quality and the interfacial effects between nanofillers and matrix. One of the findings of this work is that the presence of PBAT in the blend (PLA/PBAT) enhances the compatibility of the polymer matrix with both fillers and their dispersion quality. POLYM. COMPOS., 35:1140–1149, 2014. © 2013 Society of Plastics Engineers
- 29 December 2011
- Published by Wiley in Polymer Composites
- Vol. 33 (2) , 282-294
The role of nanofillers on the degradation behavior of polylactic acid
This study examines the effect of type and content of various nanofillers on the aging behavior of polylactic acid (PLA)/nanocomposites compared with that of pristine PLA, under specific environmental conditions, namely 80% relative humidity, 40°C temperature, and exposure time up to 6 months. Two different types of nanosized fillers (silica and montmorillonite, MMT) at three different weight fractions as well their mixtures were used for this purpose. The role of the various nanofillers on the aging of pristine PLA and its nanocomposites was investigated in terms of several experimental techniques including Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), and tensile testing. All studied samples, except those of PLA/MMT/Si nanocomposites, exhibited the same trend in properties during aging. In particular, no significant changes are noted after 1 month of aging. The materials after 3 months of aging experienced a dramatic lowering of the stress–strain curve, whereas at 6 months a reverse effect was observed. Comparing the effect of nanofiller types on the degradation, one could conclude that PLA/MMT nanocomposites exhibit a more homogeneous degradation effect, having a higher impact on yield stress in comparison with silica. In contrast, silica has a greater effect in Young's modulus and strain at break, compared with MMT. The peculiar behavior of the PLA/MMT/Si nanocomposites during aging is explained by the hindering action of the mixture of the two nanofillers on the molecular reordering of the PLA chains in the amorphous region. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers
- 29 December 2011
- Published by Wiley in Polymer Composites
- Vol. 33 (2) , 282-294
The role of nanofillers on the degradation behavior of polylactic acid
This study examines the effect of type and content of various nanofillers on the aging behavior of polylactic acid (PLA)/nanocomposites compared with that of pristine PLA, under specific environmental conditions, namely 80% relative humidity, 40°C temperature, and exposure time up to 6 months. Two different types of nanosized fillers (silica and montmorillonite, MMT) at three different weight fractions as well their mixtures were used for this purpose. The role of the various nanofillers on the aging of pristine PLA and its nanocomposites was investigated in terms of several experimental techniques including Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), and tensile testing. All studied samples, except those of PLA/MMT/Si nanocomposites, exhibited the same trend in properties during aging. In particular, no significant changes are noted after 1 month of aging. The materials after 3 months of aging experienced a dramatic lowering of the stress–strain curve, whereas at 6 months a reverse effect was observed. Comparing the effect of nanofiller types on the degradation, one could conclude that PLA/MMT nanocomposites exhibit a more homogeneous degradation effect, having a higher impact on yield stress in comparison with silica. In contrast, silica has a greater effect in Young's modulus and strain at break, compared with MMT. The peculiar behavior of the PLA/MMT/Si nanocomposites during aging is explained by the hindering action of the mixture of the two nanofillers on the molecular reordering of the PLA chains in the amorphous region. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers
- 12 October 2011
- Published by Wiley in Oxford Journal of Archaeology
- Vol. 30 (4) , 411-425
OLIVE‐MILL WASTEWATER IN ANTIQUITY. ENVIRONMENTAL EFFECTS AND APPLICATIONS
- 12 October 2011
- Published by Wiley in Oxford Journal of Archaeology
- Vol. 30 (4) , 411-425
OLIVE‐MILL WASTEWATER IN ANTIQUITY. ENVIRONMENTAL EFFECTS AND APPLICATIONS
- 26 May 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 122 (3) , 1519-1529
Comparative study of PLA nanocomposites reinforced with clay and silica nanofillers and their mixtures
This study compares the effects of two different types of nanosized fillers (silica and montmorillonite) at three different weight fractions as well their mixtures on the thermomechanical properties of polylactide (PLA). The role of aggregation and interphase was investigated in terms of several experimental techniques, including scanning electron microscopy, wide‐angle X‐ray scattering (WAXS), thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis (DMA), and tensile measurements. The experimental results clearly suggest that silica and montmorillonite have different reinforcing and toughening effects on PLA, while the combination of the two different nanofillers has a detrimental effect on the tensile properties of the material. Four micromechanics models describing the Young's modulus of the nanocomposites were used to study the different matrix–nanofiller interactions. The best fit of the experimental results was obtained with a model that assumes the presence of an interphase surrounding each nanoparticle. The increase of the nanofiller content above a certain amount was not accompanied by a corresponding increase of the interphase, because the total nanofiller surface area was counterbalanced by the creation of aggregates. It is postulated that the aggregation effect acts antagonistically to the interphase effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011
- 26 May 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 122 (3) , 1519-1529
Comparative study of PLA nanocomposites reinforced with clay and silica nanofillers and their mixtures
This study compares the effects of two different types of nanosized fillers (silica and montmorillonite) at three different weight fractions as well their mixtures on the thermomechanical properties of polylactide (PLA). The role of aggregation and interphase was investigated in terms of several experimental techniques, including scanning electron microscopy, wide‐angle X‐ray scattering (WAXS), thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis (DMA), and tensile measurements. The experimental results clearly suggest that silica and montmorillonite have different reinforcing and toughening effects on PLA, while the combination of the two different nanofillers has a detrimental effect on the tensile properties of the material. Four micromechanics models describing the Young's modulus of the nanocomposites were used to study the different matrix–nanofiller interactions. The best fit of the experimental results was obtained with a model that assumes the presence of an interphase surrounding each nanoparticle. The increase of the nanofiller content above a certain amount was not accompanied by a corresponding increase of the interphase, because the total nanofiller surface area was counterbalanced by the creation of aggregates. It is postulated that the aggregation effect acts antagonistically to the interphase effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011
- 27 July 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 119 (1) , 472-481
Effects of aging on the thermomechanical properties of poly(lactic acid)
In this study, we examined the role of environmental parameters and physical structure in the aging process of poly(lactic acid) (PLA). The role of heating history on the aging behavior of the material was also investigated. PLA samples with a D‐content of 4.25% were exposed to a relative humidity of 80% at three different temperatures, 20, 40, and 50°C (below the glass‐transition temperature of the material), at various aging periods of 30, 60, 80, 100, and 130 days. Selected samples were subjected to two consecutive heating runs. The stability of PLA was monitored by a number of techniques, including size exclusion chromatography, differential scanning calorimetry, dynamic mechanical analysis, and tensile measurements. The initial thermal processing (150°C) of the material resulted in an overall molecular weight reduction. A substantial lowering of properties was observed for PLA samples aged at 20°C for 30 days. No further loss of properties was observed for samples aged up to 40°C for several time intervals. A major portion (80–90%) of the induced changes in the tensile properties could be reversed after drying. At 50°C and 100 days of aging, a sharp decrease in the overall properties was noticed. The results seem to confirm the earlier finding that PLA degradation driven by hydrolysis needs a higher temperature (>50°C) in combination with ample time to take place. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011
- 27 July 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 119 (1) , 472-481
Effects of aging on the thermomechanical properties of poly(lactic acid)
In this study, we examined the role of environmental parameters and physical structure in the aging process of poly(lactic acid) (PLA). The role of heating history on the aging behavior of the material was also investigated. PLA samples with a D‐content of 4.25% were exposed to a relative humidity of 80% at three different temperatures, 20, 40, and 50°C (below the glass‐transition temperature of the material), at various aging periods of 30, 60, 80, 100, and 130 days. Selected samples were subjected to two consecutive heating runs. The stability of PLA was monitored by a number of techniques, including size exclusion chromatography, differential scanning calorimetry, dynamic mechanical analysis, and tensile measurements. The initial thermal processing (150°C) of the material resulted in an overall molecular weight reduction. A substantial lowering of properties was observed for PLA samples aged at 20°C for 30 days. No further loss of properties was observed for samples aged up to 40°C for several time intervals. A major portion (80–90%) of the induced changes in the tensile properties could be reversed after drying. At 50°C and 100 days of aging, a sharp decrease in the overall properties was noticed. The results seem to confirm the earlier finding that PLA degradation driven by hydrolysis needs a higher temperature (>50°C) in combination with ample time to take place. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011